2003 SSANGYONG MUSSO length

GENERAL INFORMATION 0B-5
Application
Overall Length (mm) Overall Width (mm)Overall Height (mm)Wheel Base (mm)
Tread : Front (mm)Rear (mm)
VEHICLE DIMENSIONS AND WEIGHTS
Vehicle Dimensions
Application
Manual : Curb Weight (kg)
Gross Vehicle Weight (kg)
Automatic : Curb Weight (kg)
Gross Vehicle Weight (kg)
Passenger Capacity
Vehicle Weights
Application
4656 18641735263015101520
661LA1860 2520 1916 2520 5 662NA
19682520 1989 2520 5 662LA
18902520 2005 2520 5 2.0L DOHC
19372520
--
5 2.3L DOHC
18502520 1942 25205 3.2L DOHC
19302520 2025 25205

M162 ENGINE MECHANICAL 1B1-37
7. Remove the cylinder head bolts in numerical order.Installation Notice
8. Check the length of the cylinder head bolt. Installation Notice Box Wrench Insert 000 589 01 10 00
Replace the bolt if the measured length exceed the max. length.
Apply the oil to the thread surface of bolt.
9. Carefully remove the cylinder head and check the mating surface.
10. Installation should follow the removal procedure in the reverse order.
6. Remove the guide rail fixing pin from the cylinder head using
the sliding hammer (01) and the threaded pin (02).
Sliding Hammer 116 589 20 33 00Threaded Pin 116 589 02 34 00
Tightening Torque 1st step 55 Nm
2nd step 9 0
°
3rd step 9 0 °
Length (L)New 160 ± 0.8 mm
Max. 162 ± 0.7 mm

M162 ENGINE MECHANICAL 1B1-51
Inspection
1. If the length ‘L’ of the crankshaft bearing cap bolt exceeds
63.8mm, replace it.
2. Make sure the crankshaft bearing cap is properly seated on the cylinder block (arrows).
3. Measure and record the inner diameter of the crankshaftbearing. Notice
Measure at 2 points (1, 2).
Measure ‘A’,‘B’and ‘C’ as shown. If average value of ‘B’
and ‘C’is less than value ‘A’, then the average value of
‘B’ and ‘C’ is actual average value. If average value of
‘B’ and ‘C’ is more than value ‘A’is actual average value.
4. Measure and record the diameter of the crankshaft bearing journal. Notice
Record the mean value when measured at 3 points (A,
B, C).
Measure the inner diameter of bearing and the diameter
of journal and if it is out of the standard data, replace the bearing shell.

M162 ENGINE MECHANICAL 1B1-53
FLYWHEEL / DRIVEN PLATE Preceding Work : Removal of manual or automatic transmission
1 Flywheel Mounting Bolt (M10 x 22, 8 pieces)............................................... 1st step 45+5 Nm
2nd step +90 ° +10 °
2 Plate 3 Driven Plate (A/T)
4 Dowel Pin
Service Data Standard (Stretch Bolt)
Nominal Size
Stretch Side Diameter
Bolt Length
Tightening Torque
M x 1.5
8.5 - 0.2 mm 8.0 mm
21.8 - 22.2 mm-
When New
Min. Diameter When NewDd L
1st step 50 Nm, 2nd step 90 °

M162 ENGINE MECHANICAL 1B1-89
Inspection
1. Measure the basic bore of the connecting rod bearing.Notice If the basic bore exceeds the value of 51.614mm, replace the bearing or check the connecting rod.
2. Check connecting rod bolts.
3. Check the assembly mark(indication//or number:arrow) of the connecting rods and the bearing cap when installing. Notice
Make sure it doesn ’t exceed over 4g with other
connecting rods when replacing the connecting rods.
Check if the connecting rod and the bearing cap are
accurately seated on the groove when replacing the bearing.
Notice If the length exceeds max. length, replace it.
Length When New (L)
Max. Length (L)
Tightening Torque 51.7 - 52 mm
52.9 mm
1st step 40 + 5 Nm 2nd step 90 °+10 °

M161 ENGINE MECHANICAL 1B2-43
15. Check the length of the cylinder head bolt.Tightening Torque When New 100 mm Max. Length 105 mm
Notice Replace the bolt if the measured length exceed the max. length.
16. Installation should follow the removal procedure in the reverse order.

1B2-58 M161 ENGINE MECHANICAL Inspection
1. If the length ‘L’ of the crankshaft bearing cap bolt exceeds
63.8mm, replace it.
2. Make sure the crankshaft bearing cap is properly seated on the cylinder block (arrows).
3. Measure and record the inner diameter of the crankshaftbearing. Notice
Measure at 2 points (1, 2).
Measure ‘A’,‘B’and ‘C’ as shown. If average value of
‘B’ and ‘C’is less than value ‘A’, then the average value
of ‘B’ and ‘C’ is actual average value. If average value
of ‘B’ and ‘C’ is more than value ‘A’is actual average
value.
4. Measure and record the diameter of the crankshaft bearing journal. Notice
Record the mean value when measured at 3 points
(A, B, C).
Measure the inner diameter of bearing and the
diameter of journal and if it is out of the standard data, replace the bearing shell.

1B2-60 M161 ENGINE MECHANICAL
FLYWHEEL/DRIVEN PLATE Preceding Work : Removal of manual or automatic transmission
1 Flywheel Mounting Bolt(M10 x 22, 8 pieces) ................ 1st Step 45 Nm 2nd Step 90°+10 °
2 Plate 3 Driven Plate (A/T)
4 Dowel Pin
5 Flywheel (M/T)
Service Data Standard (Stretch Bolt)
Nominal Size
Stretch Side Diameter
Bolt Length
Tightening Torque
M x 1.5
8.5 - 0.2 mm 8.0 mm
21.8 - 22.2 mm-
When New
Min. Diameter When NewDd L
1st step 50 Nm, 2nd step 90 °