2003 SSANGYONG MUSSO oil

7D-2 FATC-HAVC
Application
Size (WxHxT) Capacity
Type Description
650x339.2x22.0 11,000 Kcal/h
Parallel Flow
Condenser
Application
Material CapacityDesiccant Description
Aluminum 250cc
XH-9 or equivalent 35g
Receiver Drier
Application
Motor Type Motor Size Description
Magnetic
70 x
145
Blower Unit
Application
Replacement Description
Every 10,000 km (replace earlier if air pollution is heavy)
Air Filter
Application
Model
Type
Displacement (cc/rev.) Pulley Oil Description
FK-II(DKV 14C) Vane rotary 140.5
143.0
ZXL 200 PG (PAG Oil)
Compressor
Application
Heater Core Type Heating CapacityHeater Core Size (LxWxT) Description
2 - ROW
4,600 Kcal/h (AT 300CMH)
219.5 X 151.8 X 52
Heater Unit
Application
Type High (OFF)Low (ON) Description
Direct
OFF : 27±2Kgf/cm 2
, DIFF : 6±2Kgf/cm 2
OFF : 1.8±2Kgf/cm 2
, ON : 1.9±0.3Kgf/cm 2
Pressure Switch

9A-20 BODY WIRING SYSTEM
GASOLINE ENGINE (MSE)1 ECU Main Wiring Connector
2 ECU Main Wiring Connector
3 Crankshaft Position Sensor
4 Oil Pressure Switch
5 Knock Sensor 2
6 Hot-Film Air Mass Sensor
7 Injector 6
8 Injector 5
9 Injector 4
10 Injector 3
11 Injector 2
12 Injector 1
13 Camshaft Adjustment Magnet 14 Ignition Coil 3
15 Ignition Coil 2
16 Ignition Coil 1
17 Temperature Sensor (Gauge)
18 Double Sensor
19 Camshaft Position Sensor
20 Knock Sensor 1
21 Throttle Regulating Unit
22 Resonance Flap
23 Main Wiring Connector
2 4 ECU
25 ECU Engine Wiring Connector
26 ECU Engine Wiring Connector

BODY WIRING SYSTEM 9A-21
GASOLINE ENGINE (HFM)1 ECU
2 Main Wiring Connector
3 Crankshaft Position Sensor
4 Knock Sensor
5 Hot-Film Air Mass Sensor
6 Aspiration Sensor
7 Throttle Regulating Unit
8 Knock Sensor
9 Camshaft Position Sensor
10 Ignition Coil 3
11 Ignition Coil 2
12 Ignition Coil 1 13 Injector 6
14 Injector 5
15 Injector 4
16 Injector 3
17 Injector 2
18 Injector 1
19 Camshaft Adjustment Magnet
20 Resonance Flap
21 Temperature Sensor (Gauge)
22 Double Sensor
23 Ground

BODY WIRING SYSTEM 9A-23
MANUAL TRANSMISSION1 Main Wiring Connector ......................Diesel E/G
2 Main Wiring Connector ..................Gasoline E/G
3 Main Wiring Connector .........................Gasoline
(E32, E23) E/G
4 Back Up Switch 5 Oil Pressure Switch
6 Start Motor Solenoid
7 Micro Switch
8 Speed Sensor (Turbo Diesel Engine Only)

9A-24 BODY WIRING SYSTEM
AUTOMATIC TRANSMISSION (BENZ)1 Main Wiring Connector
2 Start Lock Switch
3 Automatic Transmission Change Over Valve
4 Transmission Overload Protection Switch ...........................Gasoline E/G 5 Oil Pressure Switch
6 Start Solenoid
7 Micro Switch
....................................... Diesel E/G
8 Speed Sensor .......................... T urbo Diesel E/G

BODY WIRING SYSTEM 9A-25
AUTOMATIC TRANSMISSION (BTRA)1 Main Wiring Connector
2 Main Wiring Connector
3 Transmission
4 Transmission Lever
5 Oil Pressure Switch ............................Diesel E/G6 Start Motor Solenoid
7 Throttle Position Sensor
....................Diesel E/G
8 Speed Sensor .......................... T urbo Diesel E/G
9 Inhibitor Switch

INSTRUMENTATION/DRIVER INFORMATION 9E-3
COMBINATION METER
COMPONENT LOCATOR
1. Speedometer
2. Odometer
3. Trip odometer
4. Tachometer
5. Coolant temperature gauge
6. Fuel gauge
7. Low fuel level warning light
8. Turn signal indicator (left)
9. Turn signal indicator (right)
10. Outside rearview mirror & tailgate heating switch
11. Reset button
12. Auto shift indicator*
13. Door open warning light
14. TCS indicator (equipped with ABD)*
21. ABS warning light* 22. EBD warning light*
23. ECS / SPORT warning light*
24. 4 - wheel warning light*
25. 4 - wheel high indicator
26. 4 - wheel low indicator
27. WINTER indicator
28. POWER indicator
29. High beam indicator
15. Alternator warning light
16. Engine oil pressure warning light
17. Brake system warning light
18. Glow indicator light (For Diesel engine)
19. Airbag warning light*
20. Seat belt reminder

GLASS AND MIRRORS 9L-5
Installation of Windshield
1. Cleaning of windshield mounting flange. Do not reuse a gauze over 20 times.
Saturate the gauze in solvent (lsoprophyl alcohol).
Keep the cleaned surface to be cleaned.
Apply body primer to the cleaned and dry body flange.
If body flange is oiled or contaminated, primer can not be applied.
Duration : 3 minutes - 8 hours (reapply after 8 hours).
If primer is applied to the body, clean off immediatelywith solvent (ethyl alcohol and ethyl acetate, 50 : 50 in volume).
Do not apply primers which is over its duration.
Be careful not to contaminate other parts.
2. Installation of windshield spacer.
Insert the spacer completely.
After inserting, there should be no clearance on the body.
- To the direction of the side spacer.
- To the direction of the lower spacer.
3. Cleaning of windshield glass. Clean the windshield glass keeping 15mm from the edge of glass.
Do not reuse a gauze over 20 times.
Saturate the gauze in solvent (lsoprophyl alcohol).
Do not touch the cleaned glass surface.
Apply glass primer to the cleaned and dry glass.
If glass is oiled or contaminated, primer can not be applied.