2003 SSANGYONG MUSSO wheel torque

STEERING WHEEL AND COLUMN 6E-3
Removal & Installation Procedure
1. Remove the horn pad from the steering wheel anddisconnect the connectors .
2. Place an alignment marks on the column shaft end and fixing nut and then remove the fixing nut. Installation Notice
3. Remove the steering wheel.
4. Remove the combination switch upper cover .
Tightening Torque 50 - 80 Nm
5. Release the crash pad panel. Notice Remove the hood release wire and the other switch connectors.

6E-4 STEERING WHEEL AND COLUMN
6. Disconnect each connectors.
7. Remove the vacuum hose from the ignition switch(Dieselonly) .
9. Remove the lower shaft by removing the bolt of the steering column shaft. Installation Notice
Tightening Torque 9 - 14 Nm
8. Remove the combination switch assembly.
10. Remove the dash panel mounting bolts. Installation Notice
Tightening Torque 30 - 40 Nm

STEERING WHEEL AND COLUMN 6E-5
Tightening Torque 30 - 40 Nm
11. Remove the steering column upper mounting bolt and pull
out steering column assembly. Installation Notice
12. Installation is reverse order of the removal.

8B-18 SUPPLEMENTAL RESTRAINT SYSTEM(SRS)
MAINTENANCE AND REPAIR ON-VEHICLE SERVICE AIR BAG MODULE Removal & Installation Procedure
1. Remove the steering wheel rid (LH,RH) with a screwdriver.Installation Notice Each position mark (LH,RH) is stamped on the inner surface of the rids.
Tightening Torque 7 - 11 Nm
3. Disconnect the connectors and remove the air bag module.
4. Installation should follow the removal procedure in thereverse order.
2. Unscrew the bolts from both sides.
Installation Notice

8. ECM(E32, HFM) .......................................................................................................................... 5-64
1) INJECTOR, OVPR, IGNITION COIL, FUEL PUMP CIRCUIT(W/ IMMOBILIZER) ........................................... 5-64
2) INJECTOR, OVPR, IGNITION COIL, FUEL PUMP CIRCUIT(W/O IMMOBILIZER) ........................................ 5-66
3) SENSOR (CKP, CMP, KNOCK, MAF), CCP SOLENOID, CAM SHAFT ACTUATOR CIRCUIT ....................... 5-68
4) THROTTLE MOTOR & SENSOR, SENSOR (IAT, ECT, HEATED O 2), VSS, CIRCUIT (UNLEAD) ................. 5-70
5) THROTTLE MOTOR & SENSOR, SENSOR (IAT, ECT), CO POTENTIO METER, VSS CIRCUIT(LEAD) ..... 5-72
9. DLC CIRCUIT ................................................................................................................. ............. 5-74
10. TCM(GSL, BTRE) .............................................................................................................. ......... 5-76
1) POWER SUPPLY, GROUND, INDICATION LAMP CIRCUIT ............................................................................. 5- 76
2) KICK DOWN SWITCH, SELECT LEVER POSITION SENSOR, TRANSMISSION CIRCUIT ........................ 5-78
11. TCM(DSL, BTRE) .............................................................................................................. ......... 5-80
1) POWER SUPPLY, GROUND, INDICATION LAMP, SENSOR (TR, ENGINE SPEED) CIRCUIT .................... 5-80
2) KICK DOWN SWITCH, SELECT LEVER POSITION SENSOR, TRANSMISSION CIRCUIT ........................ 5-82
12. KICK DOWN RELAY, 'B' SWITCH CIRCUIT (MB A/T) ........................................................... 5-84
13. TCCU-PART TIME .............................................................................................................. ........ 5-86
1) POWER SUPPLY, GROUND, INDICATION LAMP, PNP RELAY, CLUTCH SWITCH CIRCUIT ..................... 5-86
2) 4WD SWITCH, T/C SPEED SENSOR, T/C MOTOR CIRCUIT ........................................................................ 5-88
14. TCCU-FULL TIME .............................................................................................................. ........ 5-90
1) POWER SUPPLY, GROUND, INDICATION LAMP, NEUTRAL RELAY, CLUTCH CIRCUIT ............................ 5-90
2) 4WD SWITCH, T/C SPEED SENSOR, T/C MOTOR CIRCUIT ........................................................................ 5-92
15. TOD(TORQUE ON DEMAND)-E32,MSE .................................................................................. 5-94 1) POWER SUPPLY, GROUND, WARNING LAMP, 4WD SWITCH, T/C MOTOR CIRCUIT .............................. 5-94
2) T/C SPEED SENSOR, PNP RELAY, CLUTCH SWITCH, CAN CIRCUIT .......................................................... 5-96
16. ECS ......................................................................................................................... ..................... 5-98
1) POWER SUPPLY, GROUND, SENSOR(WHEEL'G, VERTICAL, LATERAL) CIRCUIT ................................... 5-98
2) ECS SWITCH, DAMPER CIRCUIT ...................................................................................................................... 5-100