2003 SSANGYONG MUSSO torque

FRONT SUSPENSION 2C-13
VERTICAL AND LATERAL SENSOR Removal & Installation Procedure
1. Disconnect vertical sensor and lateral sensor connectors.Notice When connecting the connectors, connector connection of the lateral sensor (2) should be in the right and connectorconnection of the vertical sensor (1) should face downward.
2. Unscrew bolts and remove vertical sensor and lateral sensor. Installation Notice
1 Body Vertical Acceleration Sensor(Vertical Sensor)
2 Body Lateral Acceleration Sensor (Lateral Sensor)
3. Installation should follow the removal procedure in the reverse order.
Tightening Torque 20 - 30 Nm

2D-6 REAR SUSPENSION Removal & Installation Procedure
Stabilizer bar
1. Remove the upper nut of the connecting link.
Installation Notice
2. Remove the stabilizer bar cap fixing bolts (arrow) andremove the stabilizer bar. Installation Notice
Tightening Torque 16 - 22 Nm
Distance Between the Nutend and the Screw end 10 - 13 mm
Tightening Torque 30 - 45 Nm
Lateral Rod
1. Remove the lateral rod fixing nut from the frame.
Notice Completely press the coil springs. Installation Notice
2. Remove the lateral rod fixing nut from the rear axle and remove the lateral rod. Installation Notice
Tightening Torque 150 - 180 Nm
Tightening Torque 150 - 180 Nm

REAR SUSPENSION 2D-7
Shock Absorber.
1. Remove the lower mounting nut.
Installation Notice
2. Remove the upper mounting nut and remove the shock absorber. Installation Notice
Tightening Torque 50 - 65 Nm
Upper Arm
1. Remove the upper arm fixing nut from the frame.
Installation Notice
2. Remove the upper arm fixing nut from the rear axle and remove the upper arm. Installation Notice
Tightening Torque 150 - 180 Nm
Tightening Torque 150 - 180 Nm
Lower arm
1. Remove the parking brake cable bracket.
Tightening Torque 30 - 45 Nm
Distance between the nut
end and the screw end 6 - 9 mm

2D-8 REAR SUSPENSION
2. Remove the lower arm fixing nut from the frame.Installation Notice
3. Remove the lower arm fixing nut from the rear axle andremove the lower arm. Installation Notice
Tightening Torque 150 - 180 Nm
Tightening Torque 150 - 180 Nm

TIRES AND WHEELS 2E-7
To correct unbalance, install equal weights 180 ° opposite
each other, one on the inside of the wheel and one on the outside, at the point of unbalance.
Balance Weight
6. Cautions for installation and removal. Clean the mounting surfaces of hub and wheel.
Do not apply grease or oil on the nuts and bolts (It will
cause looseness and poor tightening).
Using a jack, lift up the tire about 3cm from the ground.
Tighten nuts in a criss-cross pattern 2-3 times.10g
0.4oz
20g
0.7oz 30g
1.10oz 40g
1.40oz 50g
1.80oz 60g
2.1oz
Steel : 80 - 120Nm
Aluminium : 110 - 130NmTighten Torque

FRONT DRIVE AXLE 3A-7
Removal & Installation Procedure
1. Be careful not to change the valve when connecting thecheck valve and each hose.
2. Adjust the clearance between the retainer ring (5) and locking hub (7) using the shim(6).
Notice Shim thickness : 0.1, 0.2, 0.3, 0.5, 1.0 mm
Normal Max. 0.2 mm
3. Tighten the auto locking hub cap bolt to the specified torque and order.
Tightening Torque 50 - 60 Nm

FRONT DRIVE AXLE 3A-9
Removal & Installation Procedure
1. Remove the tire.Installation Notice
Steel Wheel
Aluminum Wheel
Tightening Torque80 - 120 Nm
110 - 130 Nm
2. Remove the autolocking hub vacuum hose.
3. With ABS Remove the wheel speed sensor from the steering knuckle. Installation Notice
4. Remove the mounting bolts and pull off the caliper assembly. Installation Notice
Tightening Torque 6 - 8 Nm
Hose Bolt
Mounting Bolt
Tightening Torque25 - 35 Nm
85 - 105 Nm
Notice Be careful not to damage the brake hose.

3A-10 FRONT DRIVE AXLE
5. With part time transfer case. 5-1.Remove the cover mounting bolts and pull off the cover. Installation Notice
5-2. Remove the snap ring of the drive shaft and pull off the
hub body. Notice
For assembly, adjust the clearance between the snap ring and hub not to exceed 0.2 mm (Shim thickness : 0.1, 0.2,0.3, 0.5, 1.0 mm).
Tightening Torque 50 - 60 Nm
6. With full time transfer case
6-1. Detach the hub cap with screw driver and remove the snap ring on drive shaft. Installation Notice
Tightening Torque 2 - 4 Nm
5-3. Remove the screws and pull off the locking hub washer.
Installation Notice Notice
For assembly, adjust the clearance between the snap ring and hub not to exceed 0.2 mm (Shim thickness : 0.1, 0.2, 0.3, 0.5, 1.0 mm).
Tightening Torque 15 Nm