2003 SSANGYONG MUSSO oil

M161 ENGINE ELECTRICAL 1E2-11
Inspection & Maintenance (for E2.3 MSE)
1. Measure the primary resistance between the cable terminals1 and 15 after removing the ignition cable wiring connector
(1 and 15) with ignition switch OFF. Notice Replace the ignition coil if out of the specified resistance.
T1/2 : between No.71 and No.69
Notice Check the ignition cable and the ECU if out of the
specified value.
3. Measure the secondary cable resistance between the ignition coil 5a and 5b using a multimeter.
2. Measure the primary voltage(T1/1) between the ECU
terminals No.72 and No.69 during the engine cranking (starter motor activated).
Specified Value 6 - 8.5 K
Specified Value0.9 - 1.6
Specified Value 200 - 350 V

OM600 ENGINE ELECTRICAL 1E3-3
1. Preheating time - control relay.Control relay functions as followings :
Switching of preheating current.
Indication of preheating finish.
Control of preheating sequence.
Indication of fault.
2. Coolant temperature sensor. Coolant temperature sensor senses coolant ’s temperature
and signals it to the preheating relay continuously.
3. Glow plug The glow plug parts are housing with M12 ´ 1.25 thread
and heating pin in housing. It is connected in a parallel circuit
with the specified voltage of 11.5V. The heating element has a heating coil and a control coil and they are connected in series.
1. Control Coil 2. Heater Coil
4. Current and temperature of glow plug Current of glow plug While the preheating system operates, current of about
30A flows in each glow plug and temperature of heating coil rises very fast.
Due to the rise of temperature, the resistance of control
coil increases therefore the current is controlled to
about 8~15A and that protects the glow plug from over-
heating.
Temperature of glow plug The temperature of the glow plug reaches up to 900 °C
after about 9 seconds and up to 1,050 °C after 30
seconds.

M162 ENGINE CONTROLS 1F1-7
41 44455657 58 59606264 65 66677172 73 74757677 78 79808182 83 86 8789
0001 02 0304 05 08091011 17 1819 20 21 2324 25 26272930 31 34 3540
Failure
code Description
Coolant temperature sensor open Coolant temperature sensor shortCoolant temperature sensor signal failureIntake temperature sensor openIntake temperature sensor short Intake temperature sensor signal failure Low battery voltageHFM sensor signal failureHFM sensor signal failure(Low)HFM sensor signal failure(High) Crankshaft position sensor signal failure (no engine revolution signal)Crankshaft position sensor signal failure(rpm > max. value)No.1 cylinder recognition failure Crankshaft position sensor signal failure (gab recognition failure)
Transmission coding failureCAN communication failure : ASR-
Transponder signal failure CAN communication failure : TCU(A/T only)CAN communication failure : TOD(E32 only)-- CAN communication failure : communication initialization failureFuel pump relay short(PWR)Fuel pump relay open/short(GND)Purge valve short
Fa
ilure
code Description
Purge valve open/short Condenser fan(HI) relay short(PWR)Condenser fan(HI) relay short(GND)No.1 knock sensor signal failureNo.2 knock sensor signal failure No.1 cylinder synchronization failure --Cluster S/W defectaveNo ignition voltage output(No.1 ignition coil) No ignition voltage output(No.2 ignition coil) No ignition voltage output(No.3 ignition coil)Crankshaft position sensor adaptation failureStart signal recognition failureNo.1 injector short(PWR) No.1 injector open/short(GND) No.2 injector short(PWR)No.2 injector open/short(GND)No.3 injector short(PWR)No.3 injector open/short(GND) No.4 injector short(PWR) No.4 injector open/short(GND)High oxygen sensor voltageLow oxygen sensor amplifying voltageOxygen sensor operating failure Not excessive lean indication in oxygen sensor(during coasting)Oxygen sensor heater short(PWR)Oxygen sensor heater open/short(GND)Low oxygen sensor voltage
SELF DIAGNOSIS FAILURE CODE

M162 ENGINE CONTROLS 1F1-21
Failurecode ItemChecking method
 Ignition:ON
Test stepRequirementSpecified
value Possible cause
10 12 11 - 14V



ECU:power
supply - terminal 30(TM.30)
2.2 


Power
supply:
- terminal 87(TM.87) 
Ignition:ON 
Power supply cable
 OVPR
IGNITION SYSTEM TEST
08, 
1.1
 1.2
1.1 
Ignition:ON
10 2 11 - 14V



Ground
cable:- Battery ground
 Ground cable
 Ground condition
(figure 1)
Diagnosis
socket
69 2
Diagnosis socket
1.2 
Ignition:ON
11 2 11 - 14V



Power
supply: - terminal 30(TM.30)
 Power supply cable
 Fuse No.8
Diagnosis socket
2.0 
Ignition:ON
51 1 11 -14V



ECU:power
supply - terminal 87(TM.87)
08, 
2.1
 2.2
2.1 
Ignition:ON 11 - 14V



Ground
cable - Electronic ground 
Ground cable
52
Diagnosis socket
11 1
Diagnosis
socket
 Ignition:OFF
11 - 14V
< 1V
3.0 
Ignition:ON
69 71 11 - 14 V



Ignition
coil(T1/1) - No.2,5 Cylinder64, 
Cable
 Ignition coil(T1/1)
 Fuse No.17
 Engine:in cranking > 10 V

1F1-22 M162 ENGINE CONTROLS
Failurecode ItemChecking method
Te s t
stepRequirementSpecified value Possible cause

6.1 


Crankshaft
position sensor:- Resistance 
Ignition:OFF
- Disconnect the coupling "NO.2"from ECU 
Cable
 Crankshaft position
sensor

6.0 
Engine:in cranking
99 100 Measure the
signal (refer to figure 6)



Crankshaft
positionsensor:- Signal
17, 18,20,67, 
6.1
 Increament failure in
driven plate
> 5 V -
99 100
99 100
1050 - 1400

7.0 
Engine:in cranking
104 106 
7.1
 Cable
 Camshaft position
sensor
Measure the
signal(refer to figure 7)



Camshaft
position sensor:- Signal
4.0 
Ignition:ON
69 72 11 -14 V



Ignition
coil(T1/2) - No.3,4 Cylinder65, 
Cable
 Ignition coil(T1/2)
 Fuse No.17
 Engine:in cranking > 10 V

Engine:in idling
- Voltage (alternating) 
Engine:in cranking
 Engine: in idling > 2.5 V -
19, 58,

5.0 
Ignition:ON
69 70 11 -14 V



Ignition
coil(T1/3) - No.1,6 Cylinder66, 
Cable
 Ignition coil(T1/3)
 Fuse No.17
 Engine:in cranking > 10 V
17, 18,20,67, Voltage value
is increased
when engine rpm is
increased

M162 ENGINE CONTROLS 1F1-23
Failurecode ItemChecking method
Te s t stepRequirementSpecified
value Possible cause
106 11 The value will
be changed in 1.2 - 1.7 V
- Voltage
(alternating)
0.9 - 1.6
71 11
71 72

Engine:in cranking
7.1 
Ignition:ON
- Remove the connector from the Camshaft positionsensor betweenNo.1 terminal andNo.3 terminal.
13
11 -14 V



Camshaft
positionsensor(E23 only)- Power supply
 Cable
 OVPR



Ignition
coil(T1/1) - primary coil voltage(No.2 and 5 cylinder) 
Engine:in cranking
(starter operating)- Measuring range: 400 V
- Time range: 100 %(using engine tester)
 Ignition:OFF 200 - 350 VCamshaft position
sensor
64, 8.0
8.1
8.1 


Connecting
resistance of ignition coilbetween T1/1 and T1/2 
Cable
 Ignition coil T1/1
 Ignition coil T1/2
72 11



Ignition
coil(T1/2) - primary coil voltage(No.3 and 4cylinder) 
Engine:in cranking
(starter operating)- Measuring range: 400 V
- Time range: 100 %(using engine tester) 200 - 350 V
65, 9.0
9.1
0.9 - 1.6
72 71
 Ignition:OFF 9.1 


Connecting
resistance of ignition coilbetween T1/2 and T1/1 
Cable
 Ignition coil T1/1
 Ignition coil T1/2
The
resistance of
ignition coil at 20°C is
approached 0.6
The
resistance of
ignition coil at 20°C is
approached 0.6

1F1-24 M162 ENGINE CONTROLS
Failurecode ItemChecking method
Test
stepRequirementSpecified
value Possible cause
8 - 20 KV



Ignition coil
(T1/1, T1/2, T1/3)
- Secondary ignition voltage
> 10 M
117 118
 Engine:in cranking - Select the ignition
coil in order of T1/1,T1/2
- Measuring range: 20KV
- Time range:100 %
 Ignition:OFF
- Disconnect the coupling "No.2" fromECU.
12.0 


Knock
sensor 1 - Resistance (cylinder No1, 2, 3) 
Connecting
condition
 Cable
 ECU

11.0
64,65,66, Engine tester

11.1
 Ignition plug
 ECU
 High tension cable
6 - 8.5 K



Ignition coil
(T1/1, T1/2, T1/3)
- Secondary coilresistance 
Remove the high
tension cable of T1/1, T1/2, T1/3.

11.1 Ignition coil
(T1/1, T1/2, T1/3) 
Ignition coil T1/1
 Ignition coil T1/2
 Ignition coil T1/3
TM.4a TM.4b
56,
11



Ignition
coil(T1/3) - primary coil voltage(No.1 and 6cylinder) 
Engine:in cranking
(starter operating)- Measuring range: 400 V
- Time range: 100 % 200 - 350 V
66, 10.0
10.1
0.9 - 1.6
70 72
 Ignition:OFF 10.1 


Connecting
resistance of ignition coilbetween T1/3 and T1/2 
Cable
 Ignition coil T1/3
 Ignition coil T1/2
> 10 M
114 115 Ignition:OFF
- Disconnect the coupling "No.2" from ECU. 13.0 


Knock
sensor 2 - Resistance (cylinder No.4, 5, 6) 
Connecting
condition
 Cable
 ECU
57,
The
resistance of
ignition coil at 20°C is
approached 0.6

M162 ENGINE CONTROLS 1F1-39
Engine Connector
Pin No.Abbreciation
Decription
61 62636465666768697071727374757677787980 EV5EV6EV1EV4EV2EV3
M+M-
TM.31
ZSC16 ZSA25ZSB34 NWS ----
MT
GND LT
Injector-cylinder 2Injector-cylinder 4Injector-cylinder 1Injector-cylinder 6Injector-cylinder 5Injector-cylinder 3E-GAS motor plusE-GAS motor minusPower ground TM.31Ignition coil cylinder 1+6Ignition coil cylinder 2+5Ignition coil cylinder 3+4Camshaft control----Engine coolant temperature
Temperature groundIntake air temperature