2003 SSANGYONG MUSSO oil

OM600 ENGINE COOLING 1D3-13
Removal & Installation Procedure
1. Drain coolant from the radiator.
2. Remove the coolant thermoswich connector from radiator.
3. Remove the each coolant hose.
4. Remove the auto T/M oil cooling hose and cooling line.Installation Notice
5. Loosen the radiator upper mounting bolt and remove the mounting stopper and insulator.
6. Remove the radiator.
7. Check the radiator pin for crack, leakage and bending and replace it if necessany.
8. Installation should follow the removal procedure in the reverse order.
Tightening Torque Hose : 29 - 40Nm

M162 ENGINE ELECTRICAL 1E1-7
1 Ignition Coil Cable Cover
2 Bolt (M6 X 60, 7 pieces)......................... 9-11 Nm
3 Spark Plug
SPARK PLUG Preceding Work : Removal of intake air ductT1/1
Ignition Coil : Cylinder 2 and 5
T1/2 Ignition Coil : Cylinder 3 and 4
T1/3 Ignition Coil : Cylinder 1 and 6

M162 ENGINE ELECTRICAL 1E1-9
IGNITION CABLE Preceding Work : Removal of intake air duct
1 Control Cable Connection
2 Ignition Cable
3 Spark Plug Connector
4 Coupling Plug5a, 5b Secondary Voltage Connection
E Iron Core
L1 Secondary Ignition Coil
L2 Primary Ignition Coil

1E1-10 M162 ENGINE ELECTRICAL Functions
1. Firing order : 1-5-3-6-2-4
2. The ignition cables are located on the cylinder head cover.Each ignition coil provides the high voltage to two spark
plugs simultaneously.
- T1/1 : cylinder 2 and 5
- T1/2 : cylinder 3 and 4
- T1/3 : cylinder 1 and 6
Removal & Installation Procedure
1. Disconnect the negative battery cable (1).
2. Remove the ignition cable connector from the ignition cable.
3. Disconnect the secondary spark plug connectors from the each spark plugs and remove the ignition cable. Installation Notice
3. The secondary output voltage (5a) is supplied to the No.2
cylinder spark plug through the spark plug connector. The secondary output voltage (5b) is supplied to the No.5 cylinderspark plug through the ignition cable. The guide pin (W)acts as a ground while the ignition cable is operated.
Make sure that the ignition cables are correctly routed.
Exactly install the ignition cable guide pin into the vehicle
to be grounded.
4. Installation should follow the removal procedure in the reverse order.
Tightening Torque 9 - 11 Nm

M162 ENGINE ELECTRICAL 1E1-11
Circuit Diagram
Inspection & Maintenance Procedure (for MSE)
1. While the ignition switch is in 'OFF' position, remove thewiring connectors (1 and 15) from ignition coil and measure the primary resistance between terminal No.1 and No.15.
2. During engine cranking, measure primary voltage (T1/1) between ECU terminal No. 71 and No. 69.
Notice If out of specified value, replace the ignition coil.
Specified Value
0.9 - 1.6 (20 °C)
Specified Value 200 - 350 V
Notice
Measure remaining cables.
- T1/2 : No. 72 and 69.
- T1/3 : No. 70 and 69.
If out of specified value, check ignition cable and ECU.
3. Using a multi-tester, measure the secondary coil resistance between 5a and 5b.
Specified Value 6 - 8.5 k

M161 ENGINE ELECTRICAL 1E2-7
SPARK PLUG Preceding Work : Removal of intake air duct
Tools Required
119 589 01 09 00 Spark Plug Wrence1 Screw (3 pieces)
.................................. 9 - 11 Nm
2 Adaptor (3 pieces)
3 Ignition Coil Cable Cover
4 Spark Plug Connector
5 Ignition Coil Connector 6 Bolts (M6 X 25, 4 pieces)
..................... 9 - 11 Nm
7 Ignition Coil (T1/1)
8 Coupling Plug
9 Spark Plug ......................................... 25 - 30 Nm
10 Ignition Coil (T1/2)

1E2-8 M161 ENGINE ELECTRICAL
Tightening Torque 9 - 11Nm
Replacement Procedure
1. Unscrew the three screws(1) and remove the ignition coil
cable cover Installation Notice
Tightening Torque
Clearance 25 - 30 Nm
0.8 + 0.1 mm
2. Disconnect the cable from ignition coil and spark plug.
4. Using the special tool, remove the spark plug . Installation Notice
Spark Plug Wrench 119 589 01 09 00
Notice
Tighten the spark plug with specified torque.
Install the ignition coil to number 2 and 4 cylinder, and
connect the cable to number 1, 4 and 2, 3 cylinder
- T1/1 : cylinder 1 and 4
- T1/2 : cylinder 2 and 3
3. Unscrew two bolts(M6 X 25) from each ignition coil and remove the ignition coil(arrow) . Installation Notice
Tightening Torque 9 - 11Nm

M161 ENGINE ELECTRICAL 1E2-9
IGNITION CABLE Preceding Work : Removal of intake air duct
1 Control Cable Connection
2 Ignition Cable
3 Spark Plug Connector
4 Coupling Plug5a, 5b Secondary Voltage Connection
E Iron Core
L1 Secondary Ignition Coil
L2 Primary Ignition Coil