2003 SSANGYONG MUSSO air condition

1B1-50 M162 ENGINE MECHANICALInstallation Notice
Make sure the crankshaft bearing cap properly seated in place in the crankcase side. When perfectly installed,the projected part (arrow) locates in the left side (intakemanifold side).
Assemble so that the projected part of the cap andcrankcase face the same direction.
Removal & Installation Procedure
1. Unscrew the connecting rod bearing cap bolt and remove
the bearing cap. Installation Notice
2. Unscrew the crankshaft bearing cap bolts and separate the upper and lower bearing shells and thrust washers. Installation Notice
Remove the bearing cap from front (pulley side) to rear.
Make sure that the upper and lower bearing shells do not change each other and coat with engine oil.
The oil grooves (arrows) in the thrust washers must faceoutward and insert the thrust bearing into the bearingcap.
There are five kinds of thrust washers by thickness. Selectthe proper washer when repaired.
3. Remove the crankshaft.
4. Installation should follow the removal procedure in the reverse order.
5. After completion of the installation, check for the rotating condition of the crankshaft.
Make sure that the upper and lower bearing shells do
not change each other.
Coat the bearing shell with engine oil.
Install the bearing cap according to the consecutive
number.
Part No. : 601 030 00 622.15 mm
Part No. : 601 030 01 62 2.20 mm
Part No. : 601 030 02 62 2.25 mm
Part No. : 601 030 03 62 2.30 mm
Part No. : 601 030 04 62 2.40 mm
Tightening Torque 40 Nm + 90 °
Tightening Torque 55 Nm + 90°

M161 ENGINE MECHANICAL 1B2-17
CRANKCASE VENTILATION SYSTEM Operation at Idling and Mid-Load
1 HFM Sensor
2 Cylinder Head Cover
3 Oil Spearation Chamber (Full-Load or OverMid-Load)
4 Intake Air Duct (Cross Pipe)
5 Vent Line (Full-Load or Over Mid-Load)
6 Throttle Valve
7 Restrictor, Diameter 1.1mm (Mid-Load at Idling)
8 Intake Manifold
9 Vent Line (Mid-Load at Idling)
10 Air Conditioner Bracket 11 Oil Separation Chamber (Mid-Load at Idling)
12 Crank Chamber
13 Oil Return Pipe
14 Oil Pan
15 Timing Gear Case Cover
16 Crankcase
17 Chain Housing
A Fresh Air
C Blow-by Gas
D Vent Connection

1B2-18 M161 ENGINE MECHANICAL Operation at Idling and Mid-Load
The throttle valve(6) is closed or very partially opened, and the vacuum pressure in intake manifold is high. The blow-by gas and the fresh air that is additionally supplied through the vent connection(D) in the crankcase in partialload gets supplied to the combustion chamber from the crank
chamber(12) through the oil separation chamber(11), air- conditioner bracket(10), vent line(9), and restrictor(7)mounted to the cylinder head. The circulated engine oil returns to the oil pan through the oil return pipe(13) at the bottom of oil separation
chamber(11). The fresh air gets supplied to the crank chamber(12) through the HFM sensor(1), intake air duct(4), vent line(5), oil separation chamber(3), chain housing(17), and the timing gear case cover(15). The additional supply of the fresh air is needed to prevent from forming the residues of the engine oil.

M161 ENGINE MECHANICAL 1B2-19
Operation When Full-Load at Partial Load
1 HFM Sensor
2 Cylinder Head Cover
3 Oil Spearation Chamber (Full-Load or OverMid-Load)
4 Intake Air Duct (Cross Pipe)
5 Vent Line (Full-Load or Over Mid-Load)
6 Throttle Valve
7 Restrictor, Diameter 1.1mm (Mid-Load at Idling)
8 Intake Manifold
9 Vent Line (Mid-Load at Idling)
10 Air Conditioner Bracket 11 Oil Separation Chamber (Mid-Load at Idling)
12 Crank Chamber
13 Oil Return Pipe
14 Oil Pan
15 Timing Gear Case Cover
16 Crankcase
17 Chain Housing
A Fresh Air
C Blow-by Gas
D Vent Connection

M161 ENGINE MECHANICAL 1B2-57
Installation Notice
Make sure the crankshaft bearing cap properly seated
in place in the crankcase side. When perfectly installed, the projected part (arrow) locates in the leftside (intake manifold side).
Assemble so that the projected part of the cap and
crankcase face the same direction.
Removal & Installation Procedure
1. Unscrew the connecting rod bearing cap bolt and remove
the bearing cap. Installation Notice
2. Unscrew the crankshaft bearing cap bolts and separate the upper and lower bearing shells and thrust washers. Installation Notice
Remove the bearing cap from front (pulley side) to
rear.
Make sure that the upper and lower bearing shells do
not change each other and coat with engine oil.
The oil grooves (arrows) in the thrust washers must
face outward and insert the thrust bearing into the bearing cap.
There are five kinds of thrust washers by thickness.
Select the proper washer when repaired.
3. Remove the crankshaft.
4. Installation should follow the removal procedure in the reverse order.
5. After completion of the installation, check for the rotating condition of the crankshaft.
Make sure that the upper and lower bearing shells do
not change each other.
Coat the bearing shell with engine oil.
Install the bearing cap according to the consecutive
number.
Part No. : 601 030 00 622.15 mm
Part No. : 601 030 01 62 2.20 mm
Part No. : 601 030 02 62 2.25 mm
Part No. : 601 030 03 62 2.30 mm
Part No. : 601 030 04 62 2.40 mm
Tightening Torque 40 Nm + 90 °
Tightening Torque 55 Nm + 90°

OM600 ENGINE MECHANICAL 1B3-15
15. Remove the air-conditioner lines from the compressor.Notice Evacuate the refrigerant before removal.
12. Remove the hose(air cleaner to turbocharger) with blowby hose.
13. Disconnect the air cleaner intake hose and remove the air cleaner cover and element.
14. Disconnect the coolant hose from the water inlet.

1B3-22 OM600 ENGINE MECHANICALWith Air Conditioner
Removal & Installation Procedure
1. Remove the nut.
2. Push the tensioning lever in direction of arrow with a rod
(F12 ´ 180mm) and pull out the bolt to the rear.
3. Push back the tensioning lever (arrow direction) to release the spring tension and remove the belt.
4. Install the poly V-belt beginning at the tensioning pulley (7). 7 Tensioning Pulley
8 Crankshaft
9 Alternator
10 Coolant Pump 11 Guide Pulley
12 Power Steering Pump
13 Aircon. Compressor
Lengthe of Belt
Length (L)
Without Air Conditioner 2,100 mm 2,040 mm

1B3-26 OM600 ENGINE MECHANICAL
POLY V-BELT ALIGNMENT & INSPECTION Without Air Conditioner
With Air Conditioner