2003 NISSAN X-TRAIL engine

CO-44
[YD22DDTi]
THERMOSTAT AND WATER PIPING

THERMOSTAT AND WATER PIPINGPFP:21200
Removal and InstallationEBS00BK9
WARNING:
Do not remove radiator cap when engine is hot. Serious burns could occur from high pressure engine
coolant escaping from radiator.
REMOVAL
1. Remove engine undercover.
2. Drain engine coolant. Refer to CO-31, "
DRAINING ENGINE COOLANT" .
CAUTION:
Perform when engine is cold.
3. Remove radiator hose (lower) from water inlet side. Refer to CO-34, "
RADIATOR" .
4. Remove water inlet and thermostat.
5. Remove thermostat housing.
1. Heater return pipe 2. Gasket 3. Thermostat housing
4. Thermostat 5. Rubber ring 6. Water inlet
7. Water inlet pipe 8. Radiator hose (lower)
PBIC2018E

THERMOSTAT AND WATER PIPING
CO-45
[YD22DDTi]
C
D
E
F
G
H
I
J
K
L
MA
CO

INSPECTION AFTER REMOVAL
Thermostat

Place a string so that it is caught in the valves of the thermostat.
Immerse fully in a container filled with water. Heat while stirring.

The valve opening temperature is the temperature at which the
valve opens and falls from the thread.

Continue heating. Check the full-open lift amount.

After checking the full-open lift amount, lower the water temper-
ature and check the valve closing temperature.
Standard values

If out of the standard, replace thermostat.
INSTALLATION
Note the following, and install in the reverse order of removal.

Install the thermostat with the whole circumference of each
flange part fit securely inside the rubber ring.

Install the thermostat with the jiggle valve facing upwards.
INSPECTION AFTER INSTALLATION

Check for leaks of engine coolant using the radiator cap tester adapter (special service tool:
EG17650301) and the radiator cap tester (commercial service tool). Refer to CO-31, "
CHECKING RADIA-
TOR SYSTEM FOR LEAKS" .

Start and warm up engine. Visually check if there is no leaks of engine coolant.
SLC252B
Item Thermostat
Valve opening temperature 80 - 84°C (176 - 183° F)
Full-open lift amount More than 10 mm/ 95°C (0.39 in/ 203 °F)
Valve closing temperature More than 77°C (171°F)
JLC300B

CO-46
[YD22DDTi]
SERVICE DATA AND SPECIFICATIONS (SDS)

SERVICE DATA AND SPECIFICATIONS (SDS)PFP:00030
Standard and LimitEBS00CU0
CAPACITY
Unit: (lmp qt)
THERMOSTAT
RADIATOR
Unit: kPa (bar, kg/cm2 , psi)
Tightening TorqueEBS00BKE
Unit: N·m (kg-m, ft-lb)
Unit: N·m (kg-m, in-lb)*
Engine coolant capacity (With reservoir tank at MAX level) Approx 9.5 (8-3/8)
Reservoir tank0.6 (1/2)
Valve opening temperature 80 - 84°C (176 - 183°F)
Full open lift amount More than 10 mm/ 95°C (0.39 in/203°F)
Valve closing temperature More than 77°C (171°F)
Cap relief pressureStandard 78 - 98 (0.78 - 0.98, 0.8 - 1.0, 11 - 14)
Limit 59 (0.59, 0.6, 9)
Leakage test pressure 157 (1.57, 1.6, 23)
Air relief plug6.9 - 7.8 (0.7 - 0.8, 61 - 69)*
Radiator mounting bracket
Cooling fan assembly
Cooling fan (left and right)
Cooling fan motors4.2 (0.42, 37)*
4.2 (0.42, 37)*
3.43 (0.35, 30)*
4.41 (0.45, 39)*
Water pump
Water pump pulley
Water inlet
Thermostat housing
Water inlet pipe
Heater return pipe26.5 (2.7, 20)
8.5 (0.86, 75)*
25 (2.6, 18)
25 (2.6, 18)
25 (2.6, 18)
25 (2.6, 18)

EC-1
ENGINE CONTROL SYSTEM
B ENGINE
CONTENTS
C
D
E
F
G
H
I
J
K
L
M
SECTION EC
A
EC

ENGINE CONTROL SYSTEM
QR (WITH EURO-OBD)
INDEX FOR DTC ...................................................... 19
Alphabetical Index .................................................. 19
DTC No. Index ....................................................... 21
PRECAUTIONS ........................................................ 24
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” ................................................................ 24
On Board Diagnostic (OBD) System of Engine and
A/T .......................................................................... 24
Precaution .............................................................. 24
Wiring Diagrams and Trouble Diagnosis ................ 27
PREPARATION ......................................................... 28
Special Service Tools ............................................. 28
Commercial Service Tools ...................................... 29
ENGINE CONTROL SYSTEM .................................. 30
System Diagram ..................................................... 30
Vacuum Hose Drawing ........................................... 32
System Chart ......................................................... 34
Multiport Fuel Injection (MFI) System .................... 34
Electronic Ignition (EI) System ............................... 37
Air Conditioning Cut Control ................................... 37
Fuel Cut Control (at No Load and High Engine
Speed) .................................................................... 38
CAN Communication Unit ...................................... 38
BASIC SERVICE PROCEDURE .............................. 44
Idle Speed and Ignition Timing Check .................... 44
Accelerator Pedal Released Position Learning ...... 45
Throttle Valve Closed Position Learning ................ 46
Idle Air Volume Learning ........................................ 46
Fuel Pressure Check .............................................. 48
ON BOARD DIAGNOSTIC (OBD) SYSTEM ............ 51
Introduction ............................................................ 51
Two Trip Detection Logic ........................................ 51
Emission-related Diagnostic Information ................ 52
NATS (Nissan Anti-theft System) ........................... 64
Malfunction Indicator (MI) ....................................... 64
OBD System Operation Chart ................................ 67
TROUBLE DIAGNOSIS ............................................ 73
Trouble Diagnosis Introduction ............................... 73DTC Inspection Priority Chart ................................. 76
Fail-safe Chart ........................................................ 77
Basic Inspection ..................................................... 79
Symptom Matrix Chart ............................................ 84
Engine Control Component Parts Location ............ 88
Circuit Diagram ....................................................... 93
ECM Harness Connector Terminal Layout ............. 95
ECM Terminals and Reference Value ..................... 95
CONSULT-II Function ...........................................102
Generic Scan Tool (GST) Function .......................112
CONSULT-II Reference Value in Data Monitor Mode
.114
Major Sensor Reference Graph in Data Monitor
Mode .....................................................................116
TROUBLE DIAGNOSIS - SPECIFICATION VALUE .119
Description ............................................................119
Testing Condition ..................................................119
Inspection Procedure ............................................119
Diagnostic Procedure ...........................................120
TROUBLE DIAGNOSIS FOR INTERMITTENT INCI-
DENT .......................................................................123
Description ............................................................123
Diagnostic Procedure ...........................................123
POWER SUPPLY AND GROUND CIRCUIT ...........124
Wiring Diagram .....................................................124
Diagnostic Procedure ...........................................125
Component Inspection ..........................................131
Ground Inspection ................................................131
DTC U1000, U1001 CAN COMMUNICATION LINE .132
Description ............................................................132
On Board Diagnosis Logic ....................................132
DTC Confirmation Procedure ...............................132
Wiring Diagram .....................................................133
Diagnostic Procedure ...........................................134
DTC P0011 IVT CONTROL .....................................135
Description ............................................................135
CONSULT-II Reference Value in Data Monitor Mode
.135
On Board Diagnosis Logic ....................................136

EC-4 CONSULT-II Reference Value in Data Monitor Mode
.302
On Board Diagnosis Logic ....................................302
DTC Confirmation Procedure ...............................302
Wiring Diagram .....................................................304
Diagnostic Procedure ...........................................307
Component Inspection ..........................................309
DTC P1128 THROTTLE CONTROL MOTOR .........310
Component Description ........................................310
On Board Diagnosis Logic ....................................310
DTC Confirmation Procedure ...............................310
Wiring Diagram .....................................................311
Diagnostic Procedure ...........................................315
Component Inspection ..........................................316
Removal and Installation ......................................317
DTC P1143 HO2S1 .................................................318
Component Description ........................................318
CONSULT-II Reference Value in Data Monitor Mode
.318
On Board Diagnosis Logic ....................................318
DTC Confirmation Procedure ...............................319
Overall Function Check ........................................319
Diagnostic Procedure ...........................................320
Component Inspection ..........................................322
Removal and Installation ......................................323
DTC P1144 HO2S1 .................................................324
Component Description ........................................324
CONSULT-II Reference Value in Data Monitor Mode
.324
On Board Diagnosis Logic ....................................324
DTC Confirmation Procedure ...............................325
Overall Function Check ........................................325
Diagnostic Procedure ...........................................326
Component Inspection ..........................................328
Removal and Installation ......................................329
DTC P1146 HO2S2 .................................................330
Component Description ........................................330
CONSULT-II Reference Value in Data Monitor Mode
.330
On Board Diagnosis Logic ....................................330
DTC Confirmation Procedure ...............................331
Overall Function Check ........................................332
Wiring Diagram .....................................................333
Diagnostic Procedure ...........................................334
Component Inspection ..........................................336
Removal and Installation ......................................337
DTC P1147 HO2S2 .................................................338
Component Description ........................................338
CONSULT-II Reference Value in Data Monitor Mode
.338
On Board Diagnosis Logic ....................................338
DTC Confirmation Procedure ...............................339
Overall Function Check ........................................340
Wiring Diagram .....................................................341
Diagnostic Procedure ...........................................342
Component Inspection ..........................................344
Removal and Installation ......................................345
DTC P1211 TCS CONTROL UNIT ..........................346
Description ............................................................346On Board Diagnosis Logic ....................................346
DTC Confirmation Procedure ................................346
Diagnostic Procedure ............................................346
DTC P1212 TCS COMMUNICATION LINE .............347
Description ............................................................347
On Board Diagnosis Logic ....................................347
DTC Confirmation Procedure ................................347
Diagnostic Procedure ............................................347
DTC P1217 ENGINE OVER TEMPERATURE ........348
System Description ...............................................348
CONSULT-II Reference Value in Data Monitor Mode
.349
On Board Diagnosis Logic ....................................349
Overall Function Check .........................................349
Wiring Diagram .....................................................352
Diagnostic Procedure ............................................355
Main 12 Causes of Overheating ...........................362
Component Inspection ..........................................363
DTC P1225 TP SENSOR ........................................364
Component Description ........................................364
On Board Diagnosis Logic ....................................364
DTC Confirmation Procedure ................................364
Diagnostic Procedure ............................................365
Removal and Installation .......................................365
DTC P1226 TP SENSOR ........................................366
Component Description ........................................366
On Board Diagnosis Logic ....................................366
DTC Confirmation Procedure ................................366
Diagnostic Procedure ............................................367
Removal and Installation .......................................367
DTC P1229 SENSOR POWER SUPPLY ................368
On Board Diagnosis Logic ....................................368
DTC Confirmation Procedure ................................368
Wiring Diagram .....................................................369
Diagnostic Procedure ............................................370
DTC P1706 PNP SWITCH .......................................373
Component Description ........................................373
CONSULT-II Reference Value in Data Monitor Mode
.373
On Board Diagnosis Logic ....................................373
DTC Confirmation Procedure ................................373
Overall Function Check .........................................373
Wiring Diagram .....................................................375
Diagnostic Procedure ............................................376
DTC P1720 VSS ......................................................378
Description ............................................................378
CONSULT-II Reference Value in Data Monitor Mode
.378
On Board Diagnosis Logic ....................................378
DTC Confirmation Procedure ................................378
Diagnostic Procedure ............................................379
DTC P1805 BRAKE SWITCH .................................380
Description ............................................................380
CONSULT-II Reference Value in Data Monitor Mode
.380
On Board Diagnosis Logic ....................................380
FAIL-SAFE MODE ................................................380
DTC Confirmation Procedure ................................380
Wiring Diagram .....................................................381

EC-5
C
D
E
F
G
H
I
J
K
L
M
ECA
Diagnostic Procedure ........................................... 382
Component Inspection ......................................... 384
DTC P2122, P2123 APP SENSOR ........................ 386
Component Description ........................................ 386
CONSULT-II Reference Value in Data Monitor Mode
. 386
On Board Diagnosis Logic ................................... 386
DTC Confirmation Procedure ............................... 387
Wiring Diagram .................................................... 388
Diagnostic Procedure ........................................... 390
Component Inspection ......................................... 392
Removal and Installation ...................................... 392
DTC P2127, P2128 APP SENSOR ........................ 393
Component Description ........................................ 393
CONSULT-II Reference Value in Data Monitor Mode
. 393
On Board Diagnosis Logic ................................... 393
DTC Confirmation Procedure ............................... 393
Wiring Diagram .................................................... 395
Diagnostic Procedure ........................................... 397
Component Inspection ......................................... 400
Removal and Installation ...................................... 400
DTC P2135 TP SENSOR ........................................ 401
Component Description ........................................ 401
CONSULT-II Reference Value in Data Monitor Mode
. 401
On Board Diagnosis Logic ................................... 401
DTC Confirmation Procedure ............................... 401
Wiring Diagram .................................................... 403
Diagnostic Procedure ........................................... 405
Component Inspection ......................................... 408
Removal and Installation ...................................... 408
DTC P2138 APP SENSOR ..................................... 409
Component Description ........................................ 409
CONSULT-II Reference Value in Data Monitor Mode
. 409
On Board Diagnosis Logic ................................... 409
DTC Confirmation Procedure ............................... 410
Wiring Diagram ..................................................... 411
Diagnostic Procedure ........................................... 413
Component Inspection ......................................... 416
Removal and Installation ...................................... 416
IGNITION SIGNAL .................................................. 417
Component Description ........................................ 417
Wiring Diagram .................................................... 418
Diagnostic Procedure ........................................... 421
Component Inspection ......................................... 426
Removal and Installation ...................................... 427
INJECTOR CIRCUIT ............................................... 428
Component Description ........................................ 428
CONSULT-II Reference Value in Data Monitor Mode
. 428
Wiring Diagram .................................................... 429
Diagnostic Procedure ........................................... 430
Component Inspection ......................................... 433
Removal and Installation ...................................... 433
VIAS ........................................................................ 434
Description ........................................................... 434
CONSULT-II Reference Value in Data Monitor Mode .435
Wiring Diagram .....................................................436
Diagnostic Procedure ...........................................438
Component Inspection ..........................................441
Removal and Installation ......................................442
FUEL PUMP CIRCUIT ............................................443
Description ............................................................443
CONSULT-II Reference Value in Data Monitor Mode
.443
Wiring Diagram .....................................................444
Diagnostic Procedure ...........................................447
Component Inspection ..........................................450
Removal and Installation ......................................450
REFRIGERANT PRESSURE SENSOR ..................451
Component Description ........................................451
Wiring Diagram .....................................................452
Diagnostic Procedure ...........................................453
Removal and Installation ......................................455
ELECTRICAL LOAD SIGNAL ................................456
CONSULT-II Reference Value in Data Monitor Mode
.456
Wiring Diagram .....................................................457
Diagnostic Procedure ...........................................464
MI & DATA LINK CONNECTORS ...........................469
Wiring Diagram .....................................................469
EVAPORATIVE EMISSION SYSTEM .....................473
Description ............................................................473
Component Inspection ..........................................476
POSITIVE CRANKCASE VENTILATION ...............478
Description ............................................................478
Component Inspection ..........................................478
SERVICE DATA AND SPECIFICATIONS (SDS) ....480
Fuel Pressure .......................................................480
Idle Speed and Ignition Timing .............................480
Calculated Load Value ..........................................480
Mass Air Flow Sensor ...........................................480
Intake Air Temperature Sensor .............................480
Engine Coolant Temperature Sensor ...................480
Heated Oxygen Sensor 1 Heater .........................480
Heated Oxygen sensor 2 Heater ..........................481
Crankshaft Position Sensor (POS) .......................481
Camshaft Position Sensor (PHASE) ....................481
Throttle Control Motor ...........................................481
Injector ..................................................................481
Fuel Pump ............................................................481
QR (WITHOUT EURO-OBD)
INDEX FOR DTC .....................................................482
Alphabetical Index ................................................482
DTC No. Index ......................................................484
PRECAUTIONS ......................................................486
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” ...............................................................486
On Board Diagnostic (OBD) System of Engine ....486
Precaution ............................................................486
Wiring Diagrams and Trouble Diagnosis ..............489

EC-6 PREPARATION .......................................................490
Special Service Tools ...........................................490
Commercial Service Tools ....................................491
ENGINE CONTROL SYSTEM ................................492
System Diagram ...................................................492
Vacuum Hose Drawing .........................................494
System Chart ........................................................496
Multiport Fuel Injection (MFI) System ...................496
Electronic Ignition (EI) System .............................499
Air Conditioning Cut Control .................................499
Fuel Cut Control (at No Load and High Engine
Speed) ..................................................................500
CAN Communication Unit .....................................500
BASIC SERVICE PROCEDURE .............................506
Idle Speed and Ignition Timing Check ..................506
Accelerator Pedal Released Position Learning ....507
Throttle Valve Closed Position Learning ...............508
Idle Air Volume Learning ......................................508
Fuel Pressure Check ............................................510
ON BOARD DIAGNOSTIC (OBD) SYSTEM ..........513
Introduction ...........................................................513
Two Trip Detection Logic ......................................513
Emission-related Diagnostic Information ..............513
NATS (Nissan Anti-theft System) ..........................515
Malfunction Indicator (MI) .....................................516
TROUBLE DIAGNOSIS ..........................................520
Trouble Diagnosis Introduction .............................520
DTC Inspection Priority Chart ...............................523
Fail-safe Chart ......................................................524
Basic Inspection ...................................................526
Symptom Matrix Chart ..........................................532
Engine Control Component Parts Location ..........536
Circuit Diagram .....................................................541
ECM Harness Connector Terminal Layout ...........543
ECM Terminals and Reference Value ...................543
CONSULT-II Function ...........................................551
CONSULT-II Reference Value in Data Monitor Mode
.561
Major Sensor Reference Graph in Data Monitor
Mode .....................................................................563
TROUBLE DIAGNOSIS - SPECIFICATION VALUE .566
Description ............................................................566
Testing Condition ..................................................566
Inspection Procedure ............................................566
Diagnostic Procedure ...........................................567
TROUBLE DIAGNOSIS FOR INTERMITTENT INCI-
DENT .......................................................................570
Description ............................................................570
Diagnostic Procedure ...........................................570
POWER SUPPLY AND GROUND CIRCUIT ...........571
Wiring Diagram .....................................................571
Diagnostic Procedure ...........................................572
Component Inspection ..........................................578
Ground Inspection ................................................578
DTC U1000, U1001 CAN COMMUNICATION LINE .579
Description ............................................................579
On Board Diagnosis Logic ....................................579
DTC Confirmation Procedure ...............................579Wiring Diagram .....................................................580
Diagnostic Procedure ............................................581
DTC P0011 IVT CONTROL .....................................582
Description ............................................................582
CONSULT-II Reference Value in Data Monitor Mode
.582
On Board Diagnosis Logic ....................................583
DTC Confirmation Procedure ................................583
Overall Function Check .........................................585
Wiring Diagram .....................................................586
Diagnostic Procedure ............................................587
Component Inspection ..........................................589
Removal and Installation .......................................589
DTC P0102, P0103 MAF SENSOR .........................590
Component Description ........................................590
CONSULT-II Reference Value in Data Monitor Mode
.590
On Board Diagnosis Logic ....................................590
DTC Confirmation Procedure ................................590
Wiring Diagram .....................................................592
Diagnostic Procedure ............................................593
Component Inspection ..........................................596
Removal and Installation .......................................596
DTC P0117, P0118 ECT SENSOR ..........................597
Component Description ........................................597
On Board Diagnosis Logic ....................................597
DTC Confirmation Procedure ................................598
Wiring Diagram .....................................................599
Diagnostic Procedure ............................................600
Component Inspection ..........................................602
Removal and Installation .......................................602
DTC P0122, P0123 TP SENSOR ............................603
Component Description ........................................603
CONSULT-II Reference Value in Data Monitor Mode
.603
On Board Diagnosis Logic ....................................603
DTC Confirmation Procedure ................................603
Wiring Diagram .....................................................605
Diagnostic Procedure ............................................607
Component Inspection ..........................................610
Removal and Installation .......................................610
DTC P0132 HO2S1 .................................................611
Component Description ........................................611
CONSULT-II Reference Value in Data Monitor Mode
.611
On Board Diagnosis Logic ....................................611
DTC Confirmation Procedure ................................612
Wiring Diagram .....................................................613
Diagnostic Procedure ............................................614
Component Inspection ..........................................616
Removal and Installation .......................................617
DTC P0134 HO2S1 .................................................618
Component Description ........................................618
CONSULT-II Reference Value in Data Monitor Mode
.618
On Board Diagnosis Logic ....................................618
Overall Function Check .........................................619
Wiring Diagram .....................................................620
Diagnostic Procedure ...........................................

EC-7
C
D
E
F
G
H
I
J
K
L
M
ECA
Component Inspection ......................................... 622
Removal and Installation ...................................... 624
DTC P0222, P0223 TP SENSOR ........................... 625
Component Description ........................................ 625
CONSULT-II Reference Value in Data Monitor Mode
. 625
On Board Diagnosis Logic ................................... 625
DTC Confirmation Procedure ............................... 625
Wiring Diagram .................................................... 627
Diagnostic Procedure ........................................... 629
Component Inspection ......................................... 632
Removal and Installation ...................................... 632
DTC P0327, P0328 KS ........................................... 633
Component Description ........................................ 633
On Board Diagnosis Logic ................................... 633
DTC Confirmation Procedure ............................... 633
Wiring Diagram .................................................... 634
Diagnostic Procedure ........................................... 635
Component Inspection ......................................... 637
Removal and Installation ...................................... 637
DTC P0335 CKP SENSOR (POS) .......................... 638
Component Description ........................................ 638
CONSULT-II Reference Value in Data Monitor Mode
. 638
On Board Diagnosis Logic ................................... 638
DTC Confirmation Procedure ............................... 638
Wiring Diagram .................................................... 640
Diagnostic Procedure ........................................... 642
Component Inspection ......................................... 644
Removal and Installation ...................................... 645
DTC P0340 CMP SENSOR (PHASE) ..................... 646
Component Description ........................................ 646
On Board Diagnosis Logic ................................... 646
DTC Confirmation Procedure ............................... 646
Wiring Diagram .................................................... 648
Diagnostic Procedure ........................................... 649
Component Inspection ......................................... 653
Removal and Installation ...................................... 653
DTC P0500 VSS ..................................................... 654
Description ........................................................... 654
On Board Diagnosis Logic ................................... 654
DTC Confirmation Procedure ............................... 654
Overall Function Check ........................................ 655
Diagnostic Procedure ........................................... 655
DTC P0550 PSP SENSOR ..................................... 656
Component Description ........................................ 656
CONSULT-II Reference Value in Data Monitor Mode
. 656
On Board Diagnosis Logic ................................... 656
DTC Confirmation Procedure ............................... 656
Wiring Diagram .................................................... 657
Diagnostic Procedure ........................................... 658
Component Inspection ......................................... 660
Removal and Installation ...................................... 660
DTC P0605 ECM .................................................... 661
Component Description ........................................ 661
On Board Diagnosis Logic ................................... 661
DTC Confirmation Procedure ............................... 661
Diagnostic Procedure ........................................... 663DTC P1065 ECM POWER SUPPLY .......................664
Component Description ........................................664
On Board Diagnosis Logic ....................................664
DTC Confirmation Procedure ...............................664
Wiring Diagram .....................................................665
Diagnostic Procedure ...........................................666
DTC P1121 ELECTRIC THROTTLE CONTROL
ACTUATOR .............................................................668
Component Description ........................................668
On Board Diagnosis Logic ....................................668
DTC Confirmation Procedure ...............................668
Diagnostic Procedure ...........................................669
Removal and Installation ......................................670
DTC P1122 ELECTRIC THROTTLE CONTROL
FUNCTION ..............................................................671
Description ............................................................671
On Board Diagnosis Logic ....................................671
DTC Confirmation Procedure ...............................671
Wiring Diagram .....................................................673
Diagnostic Procedure ...........................................677
Component Inspection ..........................................680
Removal and Installation ......................................681
DTC P1124, P1126 THROTTLE CONTROL MOTOR
RELAY .....................................................................682
Component Description ........................................682
CONSULT-II Reference Value in Data Monitor Mode
.682
On Board Diagnosis Logic ....................................682
DTC Confirmation Procedure ...............................682
Wiring Diagram .....................................................684
Diagnostic Procedure ...........................................687
Component Inspection ..........................................689
DTC P1128 THROTTLE CONTROL MOTOR .........690
Component Description ........................................690
On Board Diagnosis Logic ....................................690
DTC Confirmation Procedure ...............................690
Wiring Diagram .....................................................691
Diagnostic Procedure ...........................................695
Component Inspection ..........................................696
Removal and Installation ......................................697
DTC P1211 TCS CONTROL UNIT ..........................698
Description ............................................................698
On Board Diagnosis Logic ....................................698
DTC Confirmation Procedure ...............................698
Diagnostic Procedure ...........................................698
DTC P1212 TCS COMMUNICATION LINE ............699
Description ............................................................699
On Board Diagnosis Logic ....................................699
DTC Confirmation Procedure ...............................699
Diagnostic Procedure ...........................................699
DTC P1217 ENGINE OVER TEMPERATURE ........700
System Description ...............................................700
CONSULT-II Reference Value in Data Monitor Mode
.700
On Board Diagnosis Logic ....................................701
Overall Function Check ........................................701
Wiring Diagram .....................................................704
Diagnostic Procedure ...........................................707