2003 NISSAN TEANA Power

TERMINOLOGY
GI-47
C
D
E
F
G
H
I
J
K
L
MB
GI

Nonvolatile random access memory NVRAM ***
On board diagnostic system OBD system Self-diagnosis
Open loop OL Open loop
Oxidation catalyst OC Catalyst
Oxidation catalytic converter system OC system ***
Oxygen sensor O2S Exhaust gas sensor
Park position switch *** Park switch
Park/neutral position switch PNP switchPark/neutral switch
Inhibitor switch
Neutral position switch
Periodic trap oxidizer system PTOX system ***
Positive crankcase ventilation PCV Positive crankcase ventilation
Positive crankcase ventilation valve PCV valve PCV valve
Powertrain control module PCM ***
Programmable read only memory PROM ***
Pulsed secondary air injection control sole-
noid valvePAIRC solenoid valve AIV control solenoid valve
Pulsed secondary air injection system PAIR system Air induction valve (AIV) control
Pulsed secondary air injection valve PAIR valve Air induction valve
Random access memory RAM ***
Read only memory ROM ***
Scan tool ST ***
Secondary air injection pump AIR pump ***
Secondary air injection system AIR system ***
Sequential multiport fuel injection system SFI system Sequential fuel injection
Service reminder indicator SRI ***
Simultaneous multiport fuel injection sys-
tem*** Simultaneous fuel injection
Smoke puff limiter system SPL system ***
Supercharger SC ***
Supercharger bypass SCB ***
System readiness test SRT ***
Thermal vacuum valve TVV Thermal vacuum valve
Three way catalyst TWC Catalyst
Three way catalytic converter system TWC system ***
Three way + oxidation catalyst TWC + OC Catalyst
Three way + oxidation catalytic converter
systemTWC + OC system ***
Throttle body TBThrottle chamber
SPI body
Throttle body fuel injection system TBI system Fuel injection control
Throttle position TP Throttle position
Throttle position sensor TPS Throttle sensor
Throttle position switch TP switch Throttle switch
Torque converter clutch solenoid valve TCC solenoid valveLock-up cancel solenoid
Lock-up solenoid NEW TERMNEW ACRONYM /
ABBREVIATIONOLD TERM

GW-1
GLASSES, WINDOW SYSTEM & MIRRORS
I BODY
CONTENTS
C
D
E
F
G
H
J
K
L
M
SECTION GW
A
B
GW

GLASSES, WINDOW SYSTEM & MIRRORS
PRECAUTIONS .......................................................... 3
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” .................................................................. 3
Handling for Adhesive and Primer ........................... 3
PREPARATION ........................................................... 4
Commercial Service Tools ........................................ 4
SQUEAK AND RATTLE TROUBLE DIAGNOSES ..... 5
Work Flow ................................................................ 5
CUSTOMER INTERVIEW ..................................... 5
DUPLICATE THE NOISE AND TEST DRIVE ....... 6
CHECK RELATED SERVICE BULLETINS ........... 6
LOCATE THE NOISE AND IDENTIFY THE
ROOT CAUSE ...................................................... 6
REPAIR THE CAUSE ........................................... 6
CONFIRM THE REPAIR ....................................... 7
Generic Squeak and Rattle Troubleshooting ........... 7
INSTRUMENT PANEL .......................................... 7
CENTER CONSOLE ............................................. 7
DOORS ................................................................. 7
TRUNK .................................................................. 8
SUNROOF/HEADLINING ..................................... 8
SEATS ................................................................... 8
UNDERHOOD ....................................................... 8
Diagnostic Worksheet .............................................. 9
WINDSHIELD GLASS ...............................................11
Removal and Installation ......................................... 11
REMOVAL ............................................................ 11
INSTALLATION ................................................... 12
SIDE WINDOW GLASS ............................................ 13
Removal and Installation ........................................ 13
REMOVAL ........................................................... 13
INSTALLATION ................................................... 14
REAR WINDOW GLASS AND MOLDING ............... 15
Removal and Installation ........................................ 15
REMOVAL ........................................................... 15
INSTALLATION ................................................... 16
POWER WINDOW SYSTEM .................................... 17
Component Parts and Harness Connector Location ... 17
System Description ................................................ 17MANUAL OPERATION ........................................ 18
POWER WINDOW LOCK ................................... 20
TIMER FUNCTION .............................................. 20
ANTI-PINCH SYSTEM ........................................ 21
Schematic ............................................................... 22
Wiring Diagram — WINDOW — ............................. 23
Terminal and Reference Value for BCM ................. 27
Terminal and Reference Value for Power Window
Main Switch ............................................................ 27
Work Flow ............................................................... 28
Trouble Diagnosis Symptom Chart ......................... 29
Check BCM Power Supply and Ground Circuit ...... 30
Check Power Window Main Switch Power Supply
and Ground Circuit ................................................. 30
Check Front Power Window Motor (Driver Side) Cir-
cuit .......................................................................... 32
Check Front Power Window Motor (Passenger
Side) Circuit ............................................................ 33
Check Rear Power Window Motor RH Circuit ........ 35
Check Rear Power Window Motor LH Circuit ......... 37
Check Limit Switch Circuit (Driver Side) ................. 40
Check Encoder Circuit (Driver Side) ....................... 42
Check Door Switch ................................................. 44
Check Power Window Lock Switch ........................ 45
FRONT DOOR GLASS AND REGULATOR ............. 46
Removal and Installation ........................................ 46
DOOR GLASS ..................................................... 46
REGULATOR ASSEMBLY .................................. 47
Disassembly and Assembly .................................... 48
REGULATOR ASSEMBLY .................................. 48
Inspection after Installation ..................................... 49
SETTING OF LIMIT SWITCH (DRIVER SIDE) ... 49
FITTING INSPECTION ....................................... 49
REAR DOOR GLASS AND REGULATOR ............... 50
Removal and Installation ........................................ 50
DOOR GLASS ..................................................... 50
REGULATOR ASSEMBLY .................................. 52
Inspection after Installation ..................................... 53
FITTING INSPECTION ....................................... 53
REAR WINDOW DEFOGGER .................................. 54

GW-2 Component Parts and Harness Connector Location ... 54
System Description ................................................. 54
CAN Communication System Description .............. 56
CAN Communication Unit ....................................... 56
Schematic ............................................................... 57
Wiring Diagram — DEF — ..................................... 58
Terminal and Reference Value for BCM ................. 62
Terminal and Reference Value for IPDM E/R ......... 62
Work Flow ............................................................... 62
CONSULT-II Function (BCM) .................................. 63
CONSULT-II Start procedure .................................. 63
CONSULT-II Application Items ............................... 63
DATA MONITOR .................................................. 63
ACTIVE TEST ..................................................... 63
Trouble Diagnoses Symptom Chart ........................ 63
Check BCM Power Supply and Ground Circuit ...... 64
Check Rear Window Defogger Switch Circuit ........ 65
Check Rear Window Defogger Power Supply Cir-
cuit .......................................................................... 66
Check Rear Window Defogger Circuit .................... 67
Check Door Mirror Defogger Power Supply Circuit ... 68
Check Driver Side Door Mirror Defogger Circuit ..... 70Check Passenger Side Door Mirror Defogger Circuit
... 71
Check Filament ....................................................... 72
Filament Repair ....................................................... 72
REPAIR EQUIPMENT ......................................... 72
REPAIRING PROCEDURE ................................. 73
DOOR MIRROR ......................................................... 74
Precautions to Handle Retractable Power Door Mir-
rors .......................................................................... 74
Door Mirror .............................................................. 75
WIRING DIAGRAM — MIRROR — .................... 75
Removal and Installation ......................................... 77
REMOVAL ............................................................ 77
INSTALLATION .................................................... 77
Disassembly and Assembly .................................... 78
DISASSEMBLY .................................................... 78
ASSEMBLY .......................................................... 79
INSIDE MIRROR ....................................................... 80
Removal and Installation ......................................... 80
REMOVAL ............................................................ 80
INSTALLATION .................................................... 80

WINDSHIELD GLASS
GW-11
C
D
E
F
G
H
J
K
L
MA
B
GW

WINDSHIELD GLASSPFP:72712
Removal and InstallationBIS000Z2
REMOVAL
1. Remove the front pillar garnish. Refer to EI-38, "BODY SIDE TRIM" .
2. Partially remove the headlining (front edge). Refer to EI-54, "
HEADLINING" .
3. Remove the front wiper arms. Refer to WW-34, "
Removal and Installation of Front Wiper Arms, Adjust-
ment of Wiper Arms Stop Location" .
4. Remove the cowl top cover. Refer to EI-21, "
COWL TOP" .
5. Remove roof side molding. Refer to EI-25, "
ROOF SIDE MOLDING" .
6. Apply protective tape around the windshield glass to protect the painted surface from damage.
After removing windshield upper molding, remove glass using piano wire or power cutting tool and an inflat-
able pump bag.
PIIB1021E
1. Dam rubber 2. Windshield upper molding 3. Roof side molding
4. Fastener (RH/LH) 5. Windshield glass 6. Spacer
7. Roof 8. Panel 9. Adhesive
10. Front pillar outer panel 11. Cowl top cover (RH/LH) 12. Cowl box side

GW-12
WINDSHIELD GLASS


If a windshield glass is to be reused, mark the body and the glass with mating marks.
WARNING:
When cutting the glass from the vehicle, always wear safety glasses and heavy gloves to help prevent
glass splinters from entering your eyes or cutting your hands.
CAUTION:

When a windshield glass is to be reused, do not use a cutting knife or power cutting tool.

Be careful not to scratch the glass when removing.

Do not set or stand the glass on its edge. Small chips may develop into cracks.
7. Remove the windshield glass, using suction lifter.
INSTALLATION

Use a genuine Nissan Urethane Adhesive Kit if available or equivalent and follow the instructions fur-
nished with it.

While the urethane adhesive is curing, open a door window. This will prevent the glass from being forced
out by passenger room air pressure when a door is closed.

The molding must be installed securely so that it is in position and leaves no gap.

Inform the customer that the vehicle should remain stationary until the urethane adhesive has completely
cured (preferably 24 hours). Curing time varies with temperature and humidity.
WARNING:

Keep heat and open flames away as primers and adhesive are flammable.

The materials contained in the kit are harmful if swallowed, and may irritate skin and eyes. Avoid
contact with the skin and eyes.

Use in an open, well ventilated location. Avoid breathing the vapors. They can be harmful if
inhaled. If affected by vapor inhalation, immediately move to an area with fresh air.

Driving the vehicle before the urethane adhesive has completely cured may affect the perfor-
mance of the windshield in case of an accident.
CAUTION:

Do not use an adhesive which is past its usable term. Shelf life of this product is limited to six
months after the date of manufacture. Carefully adhere to the expiration or manufacture date
printed on the box.

Keep primers and adhesive in a cool, dry place. Ideally, they should be stored in a refrigerator.

Do not leave primers or adhesive cartridge unattended with their caps open or off.

The vehicle should not be driven for at least 24 hours or until the urethane adhesive has com-
pletely cured. Curing time varies depending on temperature and humidities. The curing time will
increase under lower temperatures and lower humidities.
Repairing Water Leaks
Leaks can be repaired without removing and reinstalling glass.
If water is leaking between the urethane adhesive material and body or glass, determine the extent of leakage.
This can be done by applying water to the windshield area while pushing glass outward.
To stop the leak, apply primer (if necessary) and then urethane adhesive to the leak point.
PIIA0186E

SIDE WINDOW GLASS
GW-13
C
D
E
F
G
H
J
K
L
MA
B
GW

SIDE WINDOW GLASSPFP:83300
Removal and InstallationBIS000Z5
REMOVAL
1. Remove the rear seat cushion and the rear seatback. Refer to SE-112, "REAR SEAT" .
2. Remove the rear seatback finisher and the rear pillar finisher. Refer to EI-38, "
BODY SIDE TRIM" .
3. Apply protective tape around the side window glass to protect the painted surface from damage.
NOTE:
If a side window glass is to be reused, mark the body and the glass with mating marks.
4. Remove the side window glass using piano wire or power cutting tool and inflatable pump bag.
WARNING:
When cutting the glass from the vehicle, always wear safety glasses and heavy gloves to help prevent
glass splinters from entering your eyes or cutting your hands.
CAUTION:

When a side window is to be reused, do not use a cutting knife or power cutting tool.

Be careful not to scratch the glass when removing.

Do not set or stand the glass on its edge. Small chips may develop into cracks.

Clips are molded to the side window glass.The clips could not replace to new ones if they are dam-
aged while removing side window glass.
PIIB1921E
1. Side window glass 2. Adhesive 3. Rear pillar finisher
4. Rear seatback finisher

REAR WINDOW GLASS AND MOLDING
GW-15
C
D
E
F
G
H
J
K
L
MA
B
GW

REAR WINDOW GLASS AND MOLDINGPFP:79712
Removal and InstallationBIS000Z6
REMOVAL
1. Partially remove the headlining (rear edge). Refer to EI-54, "HEADLINING" .
2. Remove the rear seat cushion and the rear seatback. Refer to SE-112, "
REAR SEAT" .
3. Remove the rear seatback finisher and the rear pillar finisher. Refer to EI-38, "
BODY SIDE TRIM" .
4. Remove the rear parcel shelf finisher. Refer to EI-43, "
REAR PARCEL SHELF FINISHER" .
5. Disconnect the harness connector.
6. Apply protective tape around the rear window glass to protect the painted surface from damage.

After removing moldings, remove glass using piano wire or power cutting tool and an inflatable pump bag.

If a rear window glass is to be reused, mark the body and the glass with mating marks.
1. Rear window glass 2. Spacer 3. Rear window molding
4. Dam rubber 5. Adhesive 6. Roof panel outer
7. Trunk lid outer panel
PIIB1022E

GW-16
REAR WINDOW GLASS AND MOLDING

WARNING:
When cutting the glass from the vehicle, always wear safety glasses and heavy gloves to help prevent
glass splinters from entering your eyes or cutting your hands.
CAUTION:

When a rear window glass is to be reused, do not use a cutting knife or power cutting tool.

Be careful not to scratch the glass when removing.

Do not set or stand the glass on its edge. Small chips may develop into cracks.
7. Remove the rear window glass, using suction lifter.
INSTALLATION

Use a genuine Nissan Urethane Adhesive Kit if available or equivalent and follow the instructions fur-
nished with it.

While the urethane adhesive is curing, open a door window. This will prevent the glass from being forced
out by passenger room air pressure when a door is closed.

The molding must be installed securely with the double-faced adhesive tape so that it is in position and
leaves no gap.

Inform the customer that the vehicle should remain stationary until the urethane adhesive has completely
cured (preferably 24 hours). Curing time varies with temperature and humidity.
WARNING:

Keep heat and open flames away as primers and adhesive are flammable.

The materials contained in the kit are harmful if swallowed, and may irritate skin and eyes. Avoid
contact with the skin and eyes.

Use in an open, well ventilated location. Avoid breathing the vapors. They can be harmful if
inhaled. If affected by vapor inhalation, immediately move to an area with fresh air.

Driving the vehicle before the urethane adhesive has completely cured may affect the perfor-
mance of the rear window glass in case of an accident.
CAUTION:

Do not use an adhesive which is past its usable term. Shelf life of this product is limited to six
months after the date of manufacture. Carefully adhere to the expiration or manufacture date
printed on the box.

Keep primers and adhesive in a cool, dry place. Ideally, they should be stored in a refrigerator.

Do not leave primers or adhesive cartridge unattended with their caps open or off.

The vehicle should not be driven for at least 24 hours or until the urethane adhesive has com-
pletely cured. Curing time varies depending on temperature and humidity. The curing time will
increase under lower temperature and lower humidity.
PIIB0415E