2003 NISSAN TEANA lights

ACTIVE AFS
LT-75
C
D
E
F
G
H
I
J
L
MA
B
LT

ACTIVE AFSPFP:253C0
Component Parts and Harness Connector LocationBKS002BW
System DescriptionBKS002BX
AFS (ADAPTIVE FRONT-LIGHTING SYSTEM)

Bending lamp (exclusive lamp for AFS) turn ON/OFF depending on the steering wheel angle and the vehi-
cle speed, when the headlamp LOW/HIGH lights, and the shift position is at any ranges except P.

Bending lamp supplies efficient light distribution for turning intersection and driving on the curves.

When turning to the left (right), bending lamp left (right) turn ON/OFF while driving forward or backward.
PKID0044E

ACTIVE AFS
LT-89
C
D
E
F
G
H
I
J
L
MA
B
LT

4. CHECK BENDING LAMP SIGNAL
1. Turn lighting switch to 2ND position and select lever to the other than P range.
2. The “BEND LAMP LH” and “BEND LAMP RH” with “DATA MON-
ITOR” screen, change OFF to ON when steering wheel is turned
to the left or right. And change ON to OFF when steering wheel
is returned to the straight.
Lighting operation
Lights out operation
OK or NG
OK >> GO TO 5.
NG >> Replace AFS control unit. Refer to LT- 9 4 , "
Removal and Installation of AFS Control Unit" .
5. CHECK BENDING LAMP
1. Select “ADAPTIVE LIGHT” on CONSULT-II. Select “ACTIVE
TEST” on “SELECT DIAG MODE” screen.
2. Select “LOW BEAM TEST RIGHT” or “LOW BEAM TEST LEFT”
on “SELECT TEST ITEM” screen.
3. Touch “ON” and “OFF” screen.
4. Make sure of bending lamp operation.
OK or NG
OK >> INSPECTION END. If bending lamp is not turned ON/OFF under the operating condition, replace
AFS control unit.
NG >> Refer to LT- 9 0 , "
Bending Lamps Do Not Illuminate (Both Side)" , LT- 9 1 , "Bending Lamp Does Not
Illuminate (One Side)" or LT- 9 2 , "Bending Lamp Does Not turn OFF" .
PKIB8782E
TEST ITEM Turn to the right Turn to the left
STR ANGLE SIG Less than –90°More than 90°
BEND LAMP LH ON OFF
BEND LAMP RH OFF ON
TEST ITEM Return to the straight Return to the straight
STR ANGLE SIG More than -15°Less than 15°
BEND LAMP LH OFF OFF
BEND LAMP RH OFF OFF
CONSULT-II display Operation Operation status

LOW BEAM TEST RIGHT

LOW BEAM TEST LEFTON ON
OFF OFFPKIB8784E

MA-4
DESCRIPTION

DESCRIPTIONPFP:00000
Pre-Delivery Inspection ItemsBLS0005D
Shown below are Pre-delivery Inspection Items required for the new vehicle. It is recommended that
necessary items other than those listed here be added, paying due regard to the conditions in each
country.
Perform applicable items on each model. Consult text of this section for specifications.
UNDER HOOD — engine off
Radiator coolant level and coolant hose connections for leaks
Battery fluid level, specific gravity and conditions of battery terminals
Drive belts tension
Fuel lines and connections for leaks
Engine oil level and oil leaks
Brake reservoir fluid level and fluid lines for leaks
Windshield and rear window washer and headlamp cleaner reservoir fluid level
Power steering reservoir fluid level and hose connections for leaks
ON INSIDE AND OUTSIDE
Remove front spring/strut spacer (If applicable)
Operation of all instruments, gauges, lights and accessories
Operation of horn(s), wiper and washer
Steering lock for operation
Check air conditioner for gas leaks
Front and rear seats, and seat belts for operation
All moldings, trims and fittings for fit and alignment
All windows for operation and alignment
Hood, trunk lid, door panels for fit and alignment
Latches, keys and locks for operation
Weatherstrips for adhesion and fit
Headlamp aiming
Tighten wheel nuts (Inc. inner nuts if applicable)
Tire pressure (Inc. spare tire)
Check front wheels for toe-in
Install clock/voltmeter/room lamp fuse (If applicable)
Install deodorizing filter to air conditioner (If applicable)
Remove wiper blade protectors (If applicable)
UNDER BODY
Transfer and differential gear oil level
Brake and fuel lines and oil/fluid reservoirs for leaks
Tighten bolts and nuts of steering linkage and gear box, suspension, propeller shafts and drive shafts
Tighten rear body bolts and nuts (Models with wooden bed only)
ROAD TEST
Clutch operation
Parking brake operation
Service brake operation
Automatic transmission/transaxle shift timing and kickdown
Steering control and returnables
Engine performance

TROUBLE DIAGNOSIS
SRS-29
C
D
E
F
G
I
J
K
L
MA
B
SRS

Trouble Diagnosis without CONSULT-IIBHS0004B
DIAGNOSTIC PROCEDURE 6
Inspecting SRS Malfunctioning Parts by Using “AIR BAG” Warning Lamp — Diagnosis Mode
NOTE:
SRS will not enter Diagnosis mode if no malfunction is detected in User mode.
1. Turn ignition switch ON.
2. After “AIR BAG” warning lamp lights for 7 seconds, turn ignition switch OFF within 1 second.
3. Wait more than 3 seconds.
4. Repeat the steps 1 to 3 two times.
5. Turn ignition switch ON.
SRS is now in Diagnosis mode.
“AIR BAG” warning lamp operates in Diagnosis mode as follows:
WARNING LAMP FLASH CODE CHART
PHIA0532E
PHIA0185E
SHIA0028E