2003 NISSAN TEANA clock

HEADLAMP - XENON TYPE -
LT-37
C
D
E
F
G
H
I
J
L
MA
B
LT

Disassembly and AssemblyBKS001NI
DISASSEMBLY
1. Turn plastic cap counterclockwise and unlock it.
2. Turn xenon bulb socket counterclockwise, and unlock it.
3. Unlock retaining spring, and remove xenon bulb (high/low).
4. Remove HID control unit screws.
5. Disconnect connectors and ground screw from the HID control unit.
6. Remove xenon bulb socket from headlamp housing assembly.
7. Disconnect bending lamp bulb socket.
8. Unlock retaining spring and remove bending lamp bulb.
9. Turn parking lamp bulb socket counterclockwise and unlock it.
10. Remove parking lamp bulb from its socket.
11. Turn front turn signal lamp bulb socket counterclockwise and unlock it.
12. Remove front turn signal lamp bulb from its socket.
ASSEMBLY
Note the following, and assembly is the reverse order of disassembly.
CAUTION:

When HID control unit is removed, reinstall it securely and avoid any looseness.

After installing bulb, be sure to install plastic cap and bulb socket securely to insure watertight-
ness.
1. Retaining spring 2. Parking lamp bulb 3. Parking lamp bulb socket
4. Bending lamp bulb 5. Seal packing 6. Bending lamp bulb socket
7. Plastic cap 8. Front turn signal lamp bulb 9. Front turn signal lamp bulb socket
10. Plastic cap 11. Seal packing 12. Xenon bulb socket (high/low)
13. Xenon bulb (high/low) 14. Ground screw 15. Seal packing
16. HID control unit 17. HID control unit mounting screw 18. Headlamp housing assembly
:N·m (kg-m, in-lb)
: Always replace after every disassembly.
PKIC9270J
HID control unit mounting screw : 3.2 N·m (0.32 kg-m, 28 in-lb)

LT-62
HEADLAMP - HALOGEN TYPE -

Bulb ReplacementBKS001O2
HEADLAMP (UPPER) HIGH BEAM
1. Turn lighting switch OFF.
2. Remove washer tank inlet when replacing bulb RH. Refer to WW-38, "
Removal and Installation of Washer
Ta n k" .
Remove air cleaner case when replacing bulb LH. Refer to EM-17, "
Removal and Installation" (models
with QR engine), or EM-131, "
Removal and Installation" (models with VQ engine).
3. Turn plastic cap counterclockwise and unlock it.
4. Remove the socket connected to the bulb.
5. Unlock retaining spring and remove bulb from headlamp.
HEADLAMP (LOWER) LOW BEAM
1. Turn lighting switch OFF.
2. Remove washer tank inlet when replacing bulb RH. Refer to WW-38, "
Removal and Installation of Washer
Ta n k" .
Remove air cleaner case when replacing bulb LH. Refer to EM-17, "
Removal and Installation" (models
with QR engine), or EM-131, "
Removal and Installation" (models with VQ engine).
3. Turn plastic cap counterclockwise and unlock it.
4. Remove the socket connected to the bulb.
5. Unlock retaining spring and remove bulb from headlamp.
PARKING LAMP
1. Turn lighting switch OFF.
2. Remove fender protector (front). Refer to EI-23, "
Removal and Installation" .
3. Turn bulb socket counterclockwise and unlock it.
4. Remove bulb from its socket.
FRONT TURN SIGNAL LAMP
1. Turn lighting switch OFF.
2. Remove fender protector (front). Refer to EI-23, "
Removal and Installation" .
3. Turn bulb socket counterclockwise and unlock it.
4. Remove bulb from its socket.
CAUTION:
After installing bulb, be sure to install plastic cap and bulb socket securely to ensure watertight-
ness.
Removal and InstallationBKS001O3
Refer to LT- 3 6 , "Removal and Installation" .
NOTE:
After installation, perform aiming adjustment. Refer to LT- 6 0 , "
Aiming Adjustment" . Headlamp (upper) high beam : 12V - 55W (H7)
Headlamp (lower) low beam : 12V - 55W (H11)
Parking lamp : 12V - 5W
Front turn signal lamp : 12V - 21W (amber)

HEADLAMP - HALOGEN TYPE -
LT-63
C
D
E
F
G
H
I
J
L
MA
B
LT

Disassembly and AssemblyBKS001O4
DISASSEMBLY
1. Turn plastic cap counterclockwise and unlock it.
2. Disconnect bulb socket (low).
3. Unlock retaining spring and remove bulb (low).
4. Disconnect bulb socket (high).
5. Unlock retaining spring and remove bulb (high).
6. Turn parking lamp bulb socket counterclockwise and unlock it.
7. Remove parking lamp bulb from its socket.
8. Turn front turn signal lamp bulb socket counterclockwise and unlock it.
9. Remove front turn signal lamp bulb from its socket.
ASSEMBLY
Note the following, and assembly is the reverse order of disassembly.
CAUTION:

After installing bulb, be sure to install plastic cap and bulb socket securely to insure watertight-
ness.
1. Retaining spring 2. Parking lamp bulb 3. Parking lamp bulb socket
4. Bulb (high) 5. Seal packing 6. Bulb socket (high)
7. Plastic cap 8. Front turn signal lamp bulb 9. Front turn signal lamp bulb socket
10. Plastic cap 11. Seal packing 12. Bulb socket (low)
13. Bulb (low) 14. Headlamp housing assembly
PKIC9269J

FRONT FOG LAMP
LT-141
C
D
E
F
G
H
I
J
L
MA
B
LT

Bulb ReplacementBKS001P6
1. Turn lighting switch OFF.
2. Turn off the fender protector (front) to obtain work space between the fender protector and fender.
3. Disconnect front fog lamp connector.
4. Turn front for lamp bulb counterclockwise and unlock it.
CAUTION:

Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
Never touch bulb by hand while it is lit or right after being turned off. Burning may result.

Never leave bulb out of front fog lamp reflector for a long time because dust, moisture smoke, etc.
May affect the performance of front fog lamp. When replacing bulb, be sure to replace it with new
one.
Removal and InstallationBKS001P7
REMOVAL
1. Turn over the fender protector (front) and undercover to obtain work space between the fender protector
and fender.
2. Disconnect front fog lamp connector.
3. Remove nuts (3), pawl (2) and front fog lamp (1) from front bumper.
INSTALLATION
Installation is the reverse order of removal.Front fog lamp : 12V - 35W (H8)
PKIC9218J
1. Front fog lamp 2. Pawl 3. Front fog lamp mounting nut
:N·m (kg-m, in-lb)
PKIC9219J
Front fog lamp mounting nuts : 5.1 N·m (0.52 kg-m, 45 in-lb)

TURN SIGNAL AND HAZARD WARNING LAMPS
LT-175
C
D
E
F
G
H
I
J
L
MA
B
LT

Bulb ReplacementBKS001PZ
SIDE TURN SIGNAL LAMP
1. Remove side turn signal lamp. Refer to LT- 1 7 5 , "Removal and Installation" .
2. Turn bulb socket counterclockwise and unlock it.
3. Remove bulb.
FRONT TURN SIGNAL LAMP
Refer to LT- 3 5 , "Bulb Replacement" .
REAR TURN SIGNAL LAMP
Refer to LT- 2 1 6 , "Bulb Replacement" .
Removal and InstallationBKS001Q2
SIDE TURN SIGNAL LAMP
Removal
1. While pressing side turn signal lamp to direction A (vehicle
front), pull it to direction B and then remove it.
2. Disconnect side turn signal lamp connector.
NOTE:
Support side turn signal lamp harness with tape so that it won't
fall into the front fender.
CAUTION:
Install the side turn signal lamp housing with the bead fac-
ing up.
Installation
Installation is the reverse order of removal.
FRONT TURN SIGNAL LAMP
Refer to LT- 3 6 , "Removal and Installation" .
REAR TURN SIGNAL LAMP
Refer to LT- 2 1 6 , "Removal and Installation" . Side turn signal lamp : 12V - 5W
PKIA0015E
SKIA7249E

PARKING, LICENSE PLATE AND TAIL LAMPS
LT-215
C
D
E
F
G
H
I
J
L
MA
B
LT

Bulb ReplacementBKS001QX
LICENSE PLATE LAMP
1. Remove trunk lid finisher inner. Refer to EI-59, "REMOVAL AND
INSTALLATION FOR TRUNK LID FINISHER INNER" .
2. Turn bulb socket counterclockwise and unlock it.
3. Remove bulb from its socket.
PARKING LAMP
Refer toLT- 3 5 , "Bulb Replacement" .
TAIL LAMP
Refer to LT- 2 1 6 , "Bulb Replacement" .
Removal and InstallationBKS0040M
LICENSE PLATE LAMP
Removal
1. Remove trunk lid finisher. Refer to EI-33, "Removal and Installa-
tion" .
2. While pressing the license plate lamp to left side, pull right side
of it and remove.
3. Disconnect license plate lamp connector.
Installation
Installation is the reverse order of removal.
PARKING LAMP
Refer to LT- 3 6 , "Removal and Installation" .
TAIL LAMP
Refer to LT- 2 1 6 , "Removal and Installation" . License plate lamp : 12V - 5W
SKIA6350E
SKIA6349E

LT-216
REAR COMBINATION LAMP

REAR COMBINATION LAMPPFP:26554
Bulb ReplacementBKS001R0
REAR TURN SIGNAL LAMP BULB, BACK-UP LAMP BULB AND STOP/TAIL LAMP BULB
1. Open trunk, and then remove trunk wheel house finisher. Refer to EI-58, "Removal and Installation for
Trunk Room Trim" .
2. Turn tail lamp bulb socket (1), rear turn signal lamp bulb socket
(2), back-up lamp bulb socket (3) (right side) and rear fog lamp
bulb socket (3) (left side) counterclockwise and unlock it.
3. Remove tail lamp bulb (4), rear turn signal lamp bulb (5), back-
up lamp bulb (6) (right side) and rear fog lamp bulb (6) (left
side).
Removal and InstallationBKS001R1
REMOVAL
1. Open trunk, and then remove trunk wheel house finisher. Refer to EI-58, "Removal and Installation for
Trunk Room Trim" .
2. Disconnect rear combination lamp connector.
3. Remove rear combination lamp mounting nuts (A).
4. Pull the rear combination lamp (1) toward rear of the vehicle and
remove clip (B) and locating pin (C) from the vehicle.
5. Remove seal packing (2) from rear combination lamp (1).
INSTALLATION
Installation is the reverse order of removal.
CAUTION:
Seal packing cannot be reused.Tail lamp : 12V - 5W
Rear turn signal lamp : 12V - 21W
Back-up lamp (Right side) : 12V - 21W
Rear fog lamp (Left side) : 12V - 21W
Stop lamp : LED
SKIB8646J
PKIC9679J
Rear combination lamp mounting nut : 5.1 N·m (0.52 kg-m, 45 in-lb)

MA-4
DESCRIPTION

DESCRIPTIONPFP:00000
Pre-Delivery Inspection ItemsBLS0005D
Shown below are Pre-delivery Inspection Items required for the new vehicle. It is recommended that
necessary items other than those listed here be added, paying due regard to the conditions in each
country.
Perform applicable items on each model. Consult text of this section for specifications.
UNDER HOOD — engine off
Radiator coolant level and coolant hose connections for leaks
Battery fluid level, specific gravity and conditions of battery terminals
Drive belts tension
Fuel lines and connections for leaks
Engine oil level and oil leaks
Brake reservoir fluid level and fluid lines for leaks
Windshield and rear window washer and headlamp cleaner reservoir fluid level
Power steering reservoir fluid level and hose connections for leaks
ON INSIDE AND OUTSIDE
Remove front spring/strut spacer (If applicable)
Operation of all instruments, gauges, lights and accessories
Operation of horn(s), wiper and washer
Steering lock for operation
Check air conditioner for gas leaks
Front and rear seats, and seat belts for operation
All moldings, trims and fittings for fit and alignment
All windows for operation and alignment
Hood, trunk lid, door panels for fit and alignment
Latches, keys and locks for operation
Weatherstrips for adhesion and fit
Headlamp aiming
Tighten wheel nuts (Inc. inner nuts if applicable)
Tire pressure (Inc. spare tire)
Check front wheels for toe-in
Install clock/voltmeter/room lamp fuse (If applicable)
Install deodorizing filter to air conditioner (If applicable)
Remove wiper blade protectors (If applicable)
UNDER BODY
Transfer and differential gear oil level
Brake and fuel lines and oil/fluid reservoirs for leaks
Tighten bolts and nuts of steering linkage and gear box, suspension, propeller shafts and drive shafts
Tighten rear body bolts and nuts (Models with wooden bed only)
ROAD TEST
Clutch operation
Parking brake operation
Service brake operation
Automatic transmission/transaxle shift timing and kickdown
Steering control and returnables
Engine performance