2003 NISSAN TEANA Oil

SRS-36
DRIVER AIR BAG MODULE

CAUTION:

Always work from the side of driver air bag module.

Always place driver air bag module with pad side facing
upward.

Do not insert any foreign objects (screwdriver, etc.) into
driver air bag module.

Do not disassemble driver air bag module.

Do not use old bolts after removal; replace with new bolts.

Do not expose the driver air bag module to temperatures
exceeding 90°C (194°F).

Replace driver air bag module if it has been dropped or sus-
tained an impact.

Do not allow oil, grease or water to come in contact with the
driver air bag module.
INSTALLATION
1. Connect harness connector to air bag module.
CAUTION:
Fix air bag harness on the hook for harness fixing.
2. Install the air bag module with new TORX bolts (T30).
NOTE:
Align air bag module side hole with steering wheel side hole, and then tighten special bolts when installing
air bag module. Thread is damaged and installation is incorrect if both holes are not aligned.
3. Install side lids.
4. Connect both battery cables.
5. Check SRS air bag warning lamp to make sure that the system works normally after finishing work.
6. If SRS air bag warning lamp indicates a DTC exists, reset with self-diagnosis and erase the memory using
CONSULT-II.
7. After the work is completed, perform self-diagnosis to make sure that no malfunction is detected. Refer to
SRS-16, "
SRS Operation Check" .
PHIA0594E
SBF814E
PHIA0595E

FRONT PASSENGER AIR BAG MODULE
SRS-39
C
D
E
F
G
I
J
K
L
MA
B
SRS

FRONT PASSENGER AIR BAG MODULEPFP:K8515
Removal and InstallationBHS0004G
REMOVAL
CAUTION:

Before servicing SRS, turn the ignition switch off, disconnect both battery cables and wait at least
3 minutes.

Always work from the side of or under front passenger air bag module.
1. Remove instrument passenger lower panel. Refer to IP-14, "
(K) Instrument Passenger Lower Panel" .
2. Disconnect front passenger air bag module connector.
3. Remove the front passenger air bag module fixing bolts.
4. Pull out and remove air bag module to instrument panel bottom so that no impact is given on passenger
air bag module.
CAUTION:

Always place front passenger air bag module with caution
label side facing upward.

Do not insert any foreign objects (screwdriver, etc.) into
front passenger air bag module.

Do not disassemble front passenger air bag module.

Do not use old bolts after removal; replace with new bolts.

Replace front passenger air bag module if it has been
dropped or sustained an impact.

Do not expose the front passenger air bag module to tem-
peratures exceeding 90°C (194°F).

Do not allow oil, grease or water to come in contact with the
front passenger air bag module.

After front passenger air bag module inflates, the instru-
ment panel assembly should be replaced.
INSTALLATION
Install in the reverse order of removal.
CAUTION:

Always work from the side of or under front passenger air bag module.

After the work is completed, perform self-diagnosis to make sure no malfunction is detected.
Refer to SRS-16, "
SRS Operation Check" .
PHIA0601E
PHIA0602E
SBF814E

SRS-40
FRONT SIDE AIR BAG MODULE

FRONT SIDE AIR BAG MODULEPFP:K8EH0
Removal and InstallationBHS0004H
REMOVAL
CAUTION:

Removal of front side air bag module should only be done to allow deployment of front side air
bag module prior to disposal of seatback only. Only complete seatback assemblies can be
replaced. Refer to SE-103, "
Removal and Installation" .

Before servicing SRS, turn ignition switch OFF, disconnect both battery cables and wait at least 3
minutes.

Always work from the rear of the front side air bag module.
1. Remove front seat. Refer to SE-103, "
Removal and Installation" .
2. Remove inner cloth covering side air bag module.
3. Remove seatback trim and pad. Refer to SE-103, "
Removal and Installation" .
4. Remove harness fixing clip. Then, remove side air bag module harness connector from seat cushion.
5. Remove front side air bag module assembly fixing special nuts,
then remove front side air bag module assembly.
CAUTION:

Always place the front side air bag module standing with
the stud bolt side facing down.

Do not insert any foreign objects (screwdrivers) into front
side air bag module.

Do not disassemble front side air bag module.

Replace front seatback assembly (side air bag module) if it
has been dropped or sustained an impact.

Do not expose front seatback assembly (side air bag mod-
ule) to temperatures exceeding 90°C (194°F).

Do not allow oil, grease or water to come in contact with the
front side air bag module.

After front side air bag module inflates, front seatback
assembly must be replaced. Nut: 7.4 N·m (0.75 kg-m, 65 in-lb)
PHIA0603E
PHIA0604E
SBF814E

SIDE CURTAIN AIR BAG MODULE
SRS-43
C
D
E
F
G
I
J
K
L
MA
B
SRS


Replace side curtain air bag module if it has been dropped
or sustained an impact.

Do not expose the air bag module to temperatures exceed-
ing 90°C (194°F).

Do not allow oil, grease or water to come in contact with the
side curtain air bag module.
INSTALLATION
Install in the reverse order of removal.
CAUTION:

Always work from the side of the side curtain air bag module.

After replacement of side curtain air bag module, perform self-diagnosis to make sure that no mal-
function is detected. Refer to SRS-16, "
SRS Operation Check" .
SBF814E