2003 NISSAN TEANA Unified meter and

LT-126
FRONT FOG LAMP

FRONT FOG LAMPPFP:26150
Component Parts and Harness Connector LocationBKS001OP
System DescriptionBKS001OQ

BCM (Body Control Module) controls front fog lamp operation.

IPDM E/R (Intelligent Power Distribution Module Engine Room) operates front fog lamp according to CAN
communication signals from BCM.

Unified meter and A/C amp. operates front fog lamp indicator according to CAN communication signals.
OUTLINE
Power is supplied at all times

to ignition relay (located in IPDM E/R), from battery direct,

through 15A fuse (No. 88, located in IPDM E/R)

to front fog lamp relay (located in IPDM E/R),

through 15A fuse (No. 71, located in IPDM E/R)

to CPU (central processing unit) located in IPDM E/R,

through 15A fuse (No. 78, located in IPDM E/R)

to CPU located in IPDM E/R,

through 50A fusible link (letter M, located in fuse and fusible link block)

to BCM terminal 55,

through 15A fuse [No. 17, located in fuse block (J/B)]

to BCM terminal 42 and

to combination meter terminal 7.
PKID0046E

FRONT FOG LAMP
LT-127
C
D
E
F
G
H
I
J
L
MA
B
LT

When the ignition switch is in ON or START position, power is supplied

to ignition relay (located in IPDM E/R),

through 10A fuse [No. 1, located in fuse block (J/B)]

to BCM terminal 38,

through 10A fuse [No. 14, located in fuse block (J/B)]

to combination meter terminal 8.
When the ignition switch is in ACC or ON position, power is supplied

through 10A fuse [No. 6, located in fuse block (J/B)]

to BCM terminal 11.
Ground is supplied

to BCM terminal 52 and

to combination meter terminals 10, 11 and 12

through grounds M71 and M72,

to IPDM E/R terminals 38 and 60

through grounds E1 and E31.
FRONT FOG LAMP OPERATION
When the lighting switch is in front fog lamp ON position and also in 1ST or 2ND position or AUTO position
(headlamp is ON), BCM detects FR FOG (ON) and the HEAD LAMP1, 2 (ON) or the AUTO LIGHT (ON) by
BCM combination switch reading function. And then, BCM sends front fog lamp request signal (ON) through
CAN communication.
When receiving front fog lamp request signal (ON), IPDM E/R turns ON front fog lamp relay in IPDM E/R. And
then, front fog lamp go ON. IPDM E/R supplies power

through IPDM E/R terminal 36

to front fog lamp RH terminal 1,

through IPDM E/R terminal 37

to front fog lamp LH terminal 1.
Ground is supplied

to front fog lamp RH and LH terminals 2

through grounds E1 and E31.
With power and ground supplied, the front fog lamp illuminates.
Unified meter and A/C amp. receives front fog lamp request signal (ON) through CAN communication, and
make front fog indicator go ON in combination meter.
COMBINATION SWITCH READING FUNCTION
Refer to BCS-3, "COMBINATION SWITCH READING FUNCTION" .
EXTERIOR LAMP BATTERY SAVER CONTROL
Refer to LT- 1 9 7 , "EXTERIOR LAMP BATTERY SAVER CONTROL" .
CAN Communication System DescriptionBKS001OR
CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent error detection ability. Many elec-
tronic control units are equipped onto a vehicle, and each control unit shares information and links with other
control units during operation (not independent). In CAN communication, control units are connected with 2
communication lines (CAN H line, CAN L line) allowing a high rate of information transmission with less wiring.
Each control unit transmits/receives data but selectively reads required data only.
CAN Communication UnitBKS001OS
Refer to LAN-49, "CAN System Specification Chart" .

LT-138
FRONT FOG LAMP

Front Fog Lamp Indicator Lamp Does Not IlluminateBKS001P3
1. CHECK UNIFIED METER AND A/C AMP.
1. Select “METER A/C AMP” on CONSULT-II, and perform self-
diagnosis for “METER A/C AMP”.
2. Check if malfunction is indicated.
Is malfunction indicated?
YES >> Repair or Replace malfunctioning parts.
NO >> GO TO 2.
2. CHECK COMBINATION METER INPUT SIGNAL
1. Select “METER A/C AMP” on CONSULT-II.
2. Select “DATA MONITOR” on “SELECT DIAG MODE” screen.
Make sure that “FR FOG IND” turns ON-OFF according to light-
ing switch operation.
OK or NG
OK >> Replace combination meter. Refer to DI-25, "Removal
and Installation of Combination Meter" .
NG >> Replace unified meter and A/C amp. Refer to DI-34,
"Removal and Installation of Unified Meter and A/C
Amp." .
PKIA6866E
When lighting switch is in the
front fog lamp ON position: FR FOG IND ON
PKID0089E

LT-142
REAR FOG LAMP

REAR FOG LAMPPFP:26550
Component Parts and Harness Connector LocationBKS001P8
System DescriptionBKS001P9

BCM (Body Control Module) controls rear fog lamp operation.

Unified meter and A/C amp. operates rear fog lamp indicator according to CAN communication signals
from BCM.
OUTLINE
Power is also supplied at all times

through 50A fusible link (letter M, located in fuse and fusible link block)

to BCM terminal 55,

through 15A fuse [No. 17, located in fuse block (J/B)]

to BCM terminal 42 and

to combination meter terminal 7.
When the ignition switch is in ON or START position, power is supplied

through 10A fuse [No. 1, located in fuse block (J/B)]

to BCM terminal 38,

through 10A fuse [No. 14, located in fuse block (J/B)]

to combination meter terminal 8.
When the ignition switch is in ACC or ON position, power is supplied

through 10A fuse [No. 6, located in fuse block (J/B)]

to BCM terminal 11.
PKID0047E

REAR FOG LAMP
LT-143
C
D
E
F
G
H
I
J
L
MA
B
LT

Ground is supplied

to BCM terminal 52 and

to combination meter terminals 10, 11 and 12

through grounds M71and M72.
REAR FOG LAMP OPERATION
When the lighting switch is in rear fog lamp ON position and also in 1ST or 2ND position or AUTO position
(headlamp is ON), BCM detects RR FOG (ON) and the HEAD LAMP1, 2 (ON) or the AUTO LIGHT (ON) by
BCM combination switch reading function. And then, BCM sends rear fog lamp request signal (ON) through
CAN communication.
When receiving rear fog lamp request signal (ON), BCM supplies power

through BCM terminal 67

to rear fog lamp terminal 1.
Ground is supplied

to rear fog lamp terminal 2

through grounds B16 and B17.
With power and ground supplied, the rear fog lamp illuminates.
Unified meter and A/C amp. receives rear fog lamp request signal (ON) through CAN communication, and
make rear fog lamp indicator go ON in combination meter.
COMBINATION SWITCH READING FUNCTION
Refer to BCS-3, "COMBINATION SWITCH READING FUNCTION" .
EXTERIOR LAMP BATTERY SAVER CONTROL
Refer to LT- 1 9 7 , "EXTERIOR LAMP BATTERY SAVER CONTROL" .
CAN Communication System DescriptionBKS001PA
CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent error detection ability. Many elec-
tronic control units are equipped onto a vehicle, and each control unit shares information and links with other
control units during operation (not independent). In CAN communication, control units are connected with 2
communication lines (CAN H line, CAN L line) allowing a high rate of information transmission with less wiring.
Each control unit transmits/receives data but selectively reads required data only.
CAN Communication UnitBKS001PB
Refer to LAN-49, "CAN System Specification Chart" .

LT-150
REAR FOG LAMP

5. CHECK CIRCUIT BETWEEN REAR FOG LAMP AND GROUND
1. Turn ignition switch OFF.
2. Check continuity between rear fog lamp harness connector and
ground.
OK or NG
OK >> Check rear fog lamp bulb.
NG >> Repair harness or connector.
Rear Fog Lamp Indicator Lamp Does Not IlluminateBKS001PI
1. CHECK UNIFIED METER AND A/C AMP.
1. Select “METER A/C AMP” on CONSULT-II, and perform self-
diagnosis for “METER A/C AMP”.
2. Check if malfunction is indicated.
Is malfunction indicated?
YES >> Repair or Replace malfunctioning parts.
NO >> GO TO 2.
2. CHECK COMBINATION METER INPUT SIGNAL
1. Select “METER A/C AMP” on CONSULT-II.
2. Select “DATA MONITOR” on “SELECT DIAG MODE” screen.
Make sure that “RR FOG IND” turns ON-OFF according to light-
ing switch operation.
OK or NG
OK >> Replace combination meter. DI-25, "Disassembly and
Assembly of Combination Meter" .
NG >> Replace unified meter and A/C amp. Refer to DI-34,
"Removal and Installation of Unified Meter and A/C
Amp." .
Rear fog lamp connector Terminal
GroundContinuity
B30 2 Yes
PKID0092E
PKIA6866E
When lighting switch is in the
rear fog lamp ON position: RR FOG IND ON
PKID0093E

LT-152
TURN SIGNAL AND HAZARD WARNING LAMPS

TURN SIGNAL AND HAZARD WARNING LAMPSPFP:26120
Component Parts and Harness Connector LocationBKS001PM
System DescriptionBKS001PN

BCM (Body Control Module) controls turn signal lamp (RH and LH) and hazard warning lamp operation.

Unified meter and A/C amp. operates turn (RH and LH) indicator according to CAN communication sig-
nals from BCM.
OUTLINE
Power is supplied at all times

through 50A fusible link (letter M, located in fuse and fusible link block)

to BCM terminal 55,

through 15A fuse [No. 17, located in fuse block (J/B)]

to BCM terminal 42 and

to combination meter terminal 7.
With the ignition switch in the ON or START position, power is supplied

through 10A fuse [No. 1, located in fuse block (J/B)]

to BCM terminal 38,

through 10A fuse [No. 14, located in fuse block (J/B)]

to combination meter terminal 8.
With the ignition switch in the ACC or ON position, power is supplied

through 10A fuse [No. 6, located in fuse block (J/B)]

to BCM terminal 11.
PKIB0249E

TURN SIGNAL AND HAZARD WARNING LAMPS
LT-153
C
D
E
F
G
H
I
J
L
MA
B
LT

Ground is supplied

to BCM terminal 52 and

to combination meter terminals 10, 11 and 12

through grounds M71 and M72.
TURN SIGNAL OPERATION
Turn Signal Lamp RH
When the turn signal switch is in RH position with the ignition switch in ON position, BCM detects the TURN
RH (ON) by BCM combination switch reading function. BCM outputs the flasher output signal (right) to turn
signal lamp RH intermittently. And then, turn signal lamp RH start flashing operation. BCM sends turn indicator
signal (RH) through CAN communication. BCM supplies power

through BCM terminal 46

to front combination lamp RH terminal 8

to side turn signal lamp RH terminal 1 and

to rear combination lamp RH terminal 1.
Ground is supplied

to front combination lamp RH terminal 4 and

to side turn signal lamp RH terminal 2

through grounds E1 and E31,

to rear combination lamp RH terminal 2

through grounds M71 and M72 (with rear view camera)

through grounds B16 and B17 (without rear view camera).
Unified meter and A/C amp. receives the turn indicator signal (RH) through CAN communication, then makes
turn RH indicator start flashing operation interlocked with the buzzer sounds in combination meter.
With power and ground supplied, BCM controls the blinking of the turn signal lamp RH.
Turn Signal Lamp LH
When the turn signal switch is in LH position with the ignition switch in ON position, BCM detects the TURN LH
(ON) by BCM combination switch reading function. BCM outputs the flasher output signal (left) to turn signal
lamp LH intermittently. And then, turn signal lamp LH start flashing operation. BCM sends turn indicator signal
(LH) through CAN communication. BCM supplies power

through BCM terminal 45

to front combination lamp LH terminal 8

to side turn signal lamp LH terminal 1 and

to rear combination lamp LH terminal 1.
Ground is supplied

to front combination lamp LH terminal 4 and

to side turn signal lamp LH terminal 2

through grounds E1 and E31,

to rear combination lamp LH terminal 2

through grounds M71 and M72 (with rear view camera)

through grounds B16 and B17 (without rear view camera).
Unified meter and A/C amp. receives the turn indicator signal (LH) through CAN communication, then makes
turn LH indicator start flashing operation interlocked with the buzzer sounds in combination meter.
With power and ground supplied, BCM controls the blinking of the turn signal lamp LH.
HAZARD LAMP OPERATION
When the hazard switch is in ON position, BCM detects the hazard switch signal ON. BCM outputs the flasher
output signal (right) and flasher output signal (left) to turn signal lamp (RH and LH) intermittently. And then turn
signal lamp (RH and LH) start flashing operation. And BCM sends turn indicator signal (RH and LH) through
CAN communication. Hazard switch supplies ground

to BCM terminal 29

through hazard switch terminal 2,

to hazard switch terminal 1