2003 NISSAN ALMERA N16 reset

YEL827D
1. Press “INFO” switch to display vehicle information display.
2. Indication can be changed by in the following order by push-
ing multifunction switch.
Range
Journey distance
Journey time
Average fuel economy
Average vehicle speed
Board computer Display
Range (km or MILES) Displays range to empty with a range of 000.0 to 999.9.
Journey distance (km or MILES) Displays journey distance with a range of 000.0 to 9999
Journey time Displays journey time with a range of 0000:00:00 to 9999:59:59.
Average fuel consumption (/100 km or
MPG)Displays fuel consumption with a range of 00.0 to 999.
Average vehicle speed (km/h or MPH) Displays average vehicle speed with a range of 000 to 999.
RangeNJEL0555S0401The elapsed time indication provides driver with an estimation
of the distance that can be driven before refuelling.The range
is conducted by fuel tank level sensor unit (fuel remaining),
ECM pulse signal (fuel consumption) and vehicle speed signal.
Indication will be renewed every 30 seconds.
When fuel remaining is less than approx. 7.8(6-7/8 Imp qt),
indication will blink as a warning. If the fuel remaining less than
approx. 6.8(6 Imp qt), “– –.–” will be indicated. In this case,
the mode will change to the RANGE mode automatically even
though the display is showing a different item. (See NOTE.)
The range mode includes a low range warning feature: when
the fuel level is low, the range mode is automatically selected
and the digits blink in order to draw the driver′s attention. Press
the “INFO” switch if you wish to return to the mode that was
selected before the warning occurred. The range mark will
remain blinking until next refuelling. When the fuel level drops
even lower, the range display will change to “– – – –”.
Journey DistanceNJEL0555S0402Journey distance indication is conducted by vehicle speed sig-
nal.
If journey distance is reset, journey time will be reset at the
same time.
When pushing “INFO” switch more than approximately 1
second, driving distance will be reset.
Journey TimeNJEL0555S0403Journey time indication is conducted by integration of ignition
ON time.
If journey time is reset, journey distance will be reset at the
same time.
Average Fuel ConsumptionNJEL0555S0404Average fuel consumption indication is conducted by ECM
pulse signal and vehicle speed signal after system is reset.
Indication will be renewed every 30 seconds.
VFD DISPLAY
System Description (Cont’d)
EL-216

When pushing “INFO” switch more than approximately 1
second, average fuel economy will be reset.
If average fuel consumption is reset, average vehicle speed
will be reset at the same time.
After reset operation, the display shows “– –. –” until the
vehicle is driven 500 m (1,600 ft) or 30 seconds has passed.
Average Vehicle SpeedNJEL0555S0405Average vehicle speed indication is conducted by running dis-
tance and running time.
Indication will be renewed every 30 seconds.
When pushing “INFO” switch more than approximately 1
second, average speed will be reset.
If average vehicle speed is reset, average fuel consumption
will be reset at the same time.
After reset operation, the displays shows “– –.–” for 30 sec-
onds.
HOW TO CHANGE/RESET INDICATIONNJEL0555S05Indication can be changed by in following order by pushing “INFO”
switch less than approximately 1 second.
RANGE,JOURNEY DISTANCE,JOURNEY TIME,AVER-
AGE FUEL CONSUMPTION,AVERAGE VEHICLE SPEED
Continuous pushing the “INFO” switch (more than 3 second)
can reset the indication of journey distance (trip), journey time
(hour meter), average fuel consumption and average vehicle
speed.
NOTE:
After the display changes automatically, the indication can be
changed to the last mode by pushing the switch. In this case, the
cursor will blink as a warning.
Component Parts and Harness Connector and
Harness Connector Location
NJEL0556For details, refer to “ELECTRICAL UNIT LOCATION” (EL-543) and
“HARNESS LAYOUT” (EL-550).
GI
MA
EM
LC
EC
FE
CL
MT
AT
AX
SU
BR
ST
RS
BT
HA
SC
IDX
VFD DISPLAY
System Description (Cont’d)
EL-217

MKIB0144E
Drive InformationNJEL0571S05011. Select “Drive”.
2. Elapsed time, driving distance and average speed are dis-
played as drive information. When pushing “ENTER”, elapsed
time, driving distance and average speed are all reset.
MKIB0145E
Fuel Economy InformationNJEL0571S05021. Select “Fuel Economy”.
2. Average Fuel Economy, Distance to Empty, Fuel Economy are
displayed as Fuel Economy information.
SKIA0772E
3. Select “Fuel Economy Record”. The average fuel consumption
history will be displayed in graph along with the average for the
previous Reset – to – Reset period.
MKIB0146E
Maintenance InformationNJEL0571S05031. Select “Maintenance”.
2. Engine Oil, Oil Filter, Custom 1 and Custom 2 are displayed as
maintenance information.
WARNING INDICATIONSNJEL0571S06When combination meter receives warning signal from some con-
trol units or sensors, then combination meter warning lamp is illu-
minated.
Then combination meter sends warning signal to display unit warn-
ing indications on the screen.
LCD DISPLAY
System Description (Cont’d)
EL-240

Warning indicatorsWarning lamps in
instrument panelWarning detection and cancel conditions Cases of malfunction
DOOR OPEN DoorDetection conditionVehicle is running [approx. 5
km/h (3 MPH) or faster] and door
ajar of any of the doors is
detected.Doorisopen
Cancel conditionVehicle is stopped and all the
doors lock.
ABS ABSDetection conditionWarning lamp ON signal is
detected when engine is running.
ABS control system mal-
function
Cancel conditionWarning lamp OFF signal is
detected.
ESP ELECTRONIC
CONTROL SYSTEMESPDetection conditionWarning lamp ON signal is
detected when engine is running.
ESP system malfunction
Cancel conditionWarning lamp OFF signal is
detected.
CVT ELECTRONIC
CONTROL SYSTEMCVTDetection conditionWarning lamp ON signal is
detected after ignition switch is
turned ON.
TCM system malfunction
Cancel conditionWarning lamp OFF signal is
detected.
CRUISE CONTROL
SYSTEMCRUISEDetection conditionWarning lamp ON signal is
detected after ignition switch is
turned ON.
ICC system malfunction
Cancel conditionWarning lamp OFF signal is
detected.
Precautions for Display Unit ReplacementNJEL0572Record the following memorized contents before replacing the control unit.

Preset frequency
Area for indicating station, selection of overlapped stations

Program status

Volume balance memory set values
Equalizer memory set values

Brightness of light when ON/OFF
Dimming switching
Display color switching
Replace the display unit after disconnecting both battery cables.
Component Parts and Harness Connector and
Harness Connector Location
NJEL0573For details, refer to “ELECTRICAL UNIT LOCATION” (EL-543) and “HARNESS LAYOUT” (EL-550).
LCD DISPLAY
System Description (Cont’d)
EL-242

Description=NJEL0485The TCU is applied for YD engine models without common rail and K9K engine models.
The TCU has the following functions.
INTERIOR LAMP TIMERNJEL0485S01The interior lamp timer is controlled by the TCU.
For further information, refer to “INTERIOR ROOM LAMP” (EL-80).
IGNITION KEY WARNING CHIME AND LIGHT WARNING CHIMENJEL0485S02The ignition key and light warning chime are controlled by the TCU.
For further information, refer to “WARNING CHIME” (EL-136).
REAR WINDOW DEFOGGER TIMERNJEL0485S03The rear window defogger and door mirror defogger system are controlled bythe TCU.
For further information, refer to “REAR WINDOW DEFOGGER” (EL-174).
POWER DOOR LOCK (SUPER LOCK)NJEL0485S04The power door lock (super lock) is controlled by the TCU.
For further information, refer to “POWER DOOR LOCK — Super Lock —” (EL-301).
MULTI-REMOTE CONTROL SYSTEMNJEL0485S05The multi-remote control system is controlled by the TCU.
For further information, refer to “MULTI-REMOTE CONTROL SYSTEM” (EL-352).
FUNCTIONNJEL0485S06The TCU has the following control function.
Item Details of control
Direction indicatorsSwitches the director indicators (Left, Right or All) when the combination
switch or hazard switch is operated.
Light warning chimeSounds warning chime when driver’s door is opened with light switch in the
1st or 2nd position and ignition switch “OFF”.
Ignition key warning chineSounds warning chime when driver’s door is opened with key in ignition and
the driver door lock knob (unlock sensor) is moved from the “unlock” posi-
tion to the “lock” position.
Rear window defogger timerTurn off rear window defogger and door mirror heater, if equipped, about 15
minutes after the rear window defogger switch is turned “ON”.
Battery saverShuts off interior lamp in 30 minutes if any door is left open when ignition
switch is “OFF”. The battery saver will reset if ignition switch is cycled or any
door is opened or closed.
Interior lamp timerKeep interior lamp illuminated for about 30 seconds when:
driver’s door is unlocked,
the ignition is switched off,
driver’s door is opened and then closed.
The timer is cancelled, and interior lamp turns off when:
driver’s door is locked, or
ignition switch is turned “ON”.
Power door lock Centrally locks and unlocks the vehicle
Super lock Activates and de-activates the super lock system.
GI
MA
EM
LC
EC
FE
CL
MT
AT
AX
SU
BR
ST
RS
BT
HA
SC
IDX
TIME CONTROL UNIT
Description
EL-381

SKIA1400E
GUIDE VOLUME SETTINGNJEL0592S21DescriptionNJEL0592S2101Following voice guidance setting can be changed.
Activation/Deactivation SettingNJEL0592S2102The voice prompt can be turned on/off by pressing the “Guid-
ance Volume” button.
Voice Volume SettingNJEL0592S2103Volume of the voice can be controlled by bending the joystick
to left/right.
NATS NAVI LINKNJEL0592S22DescriptionNJEL0592S2201The link with the NATS IMMU implies that the AV and NAVI control
unit can basically only be operated if connected to the matching
NATS IMMU to which the AV and NAVI control unit was initially fit-
ted on the production line.
The Navigation system does not operate because it is judged that
the code collation with NATS IMMU is illegal when the control unit
of other cars is installed.
Precautions for AV and NAVI Control Unit
Replacement
NJEL0593When replacing the AV and NAVI control unit, eject the map
DVD-ROM before disconnecting the battery.
The AV and NAVI control unit has the following information
stored in its memory. Record the memory contents before
replacing the control unit, and input them in the new unit as
necessary.

Preset frequency
Area for indicating station, selection of overlapped sta-
tions

Program status

Volume balance memory set values
Equalizer memory set values

Brightness of light when ON/OFF
Dimming switching
Display color switching
NAVIGATION SYSTEM
System Description (Cont’d)
EL-440

Error itemPossible causes
Example of symptom
Action/symptom
GPS antenna
disconnectedMalfunctioning connection between GPS substrate in AV and
NAVI control unit and GPS antenna.Navigation location detection performance
has deteriorated.
(Location correction using GPS is not per-
formed.)
GPS receiving status remains gray. Perform the self-diagnosis.
When connection between AV and NAVI control unit and GPS
antenna is judged normal by self-diagnosis, the symptom may
be intermittent, caused by impact or vibration.
Low voltage
of GPSThe power voltage supplied to the GPS circuit board has
decreased.Navigation location detection performance
has deteriorated.
(Location correction using GPS is not per-
formed.)
GPS receiving status remains gray. Perform the self-diagnosis.
When connection between AV and NAVI control unit and GPS
antenna is judged normal by self-diagnosis, the symptom may
be intermittent, caused by impact or vibration.
DVD-ROM
Malfunction
DVD-ROM
Read error
DVD-ROM
Response
ErrorMalfunctioning AV and NAVI control unit -
Dedicated map DVD-ROM is in the system, but the data cannot
be read.
The map of a particular location cannot be
displayed.
Specific guidance information cannot be dis-
played.
Map display is slow.
Guidance information display is slow.
System has been affected by vibration. Is map DVD-ROM damaged, warped, or dirty?
– If damaged or warped, the map DVD-ROM is malfunctioning.
– If dirty, wipe the DVD-ROM clean with a soft cloth.
Perform the self-diagnosis.
When AV and NAVI control unit is judged normal by self-
diagnosis, the symptom is judged intermittent, caused by
vibration.
AUTO CLIMATE CONTROLNJEL0604S07“ATC Automatic Air Conditioner” ATC-42, “Self-diagnosis Func-
tion” for the details.
SKIA1621E
SERVICENJEL0604S08To set Service schedule, change Journey distance with joy-
stick. At the same time, the marker of journey distance will be
moved.
SKIA1622E
To reset to initial distance, select “Reset” and push “ENTER”.
When the indicator of “Service Information Display” is set
green, the color of the journey distance marker will be red. And
automatically Service information screen will be displayed
when journey distance is reached on service schedule.
NAVIGATION SYSTEM
Confirmation/Adjustment Mode (Cont’d)
EL-466

ROUTE SEARCHINGNJEL0633S05
Symptom Cause Remedy
No route is shown. No road to be searched is found around the
destination.Find wider road (orange road or wider)
nearby and reset the destination and pass-
ing points onto it. Take care of the traveling
direction when there are separate up and
down roads.
Starting point and the destination are too close. Set the destination at more distant point.
Conditional traffic regulation (day of the week/
time of the day) is set at the area around the
current position or the destination.Turn the time-regulating search conditions
OFF. Turn “Avoid regulation time” in the
search conditions OFF.
Indicated route is intermittent. In some areas, highways (gray routes) are not
used for the search Therefore, the route to the
current position or the passing points may be
intermittent.System is not malfunction.
When the vehicle has passed the
recommended route, it is deleted
from the screen.A recommended route is controlled by each
section. When the vehicle has passed the pass-
ing point 1, then the map data from the starting
point up to the passing point 1 will be deleted.
(The data may remain undeleted in some area.)System is not malfunction.
Detouring route is recommended. In some areas, highways (gray routes) arenot
used for the search. Therefore, detour route
may be recommended.Set the route closer to the basic route (gray
route).
A detour route may be shown when some traffic
regulation (one-way traffic, etc.) is set at the
area around the starting point or the destina-
tion.Slightly move the starting point or the
destination, or set the passing point on the
route of your choice.
In the area where highways (gray routes) are
used for the search, left turn has priority around
the current position and the destination (pass-
ing points). For this reason, the recommended
route may be detouring.System is not malfunction.
Landmarks on the map do not
match the actual ones.This can happen due to omission or error in the
map data.As a rule, an updated map DVD-ROM will
be released once a year. Wait until the lat-
est map has become available.
Recommended route is far from
the starting point, passing points,
and destination.Starting point, passing points, and destination
of the route guide were set far from the desired
points because route searching data around
these area were not stored.Reset the destination onto the road nearby.
If this road is one of the highways (gray
routes), an ordinary road nearby may be
displayed as the recommended route.
NAVIGATION SYSTEM
Example of Symptoms Judged Not Abnormal (Cont’d)
EL-502