2003 MITSUBISHI SHOGUN park assist

Operation of the automatic trans-
mission INVECS II Sport Mode 5A/T
EI04D-Ch
CAUTION
(1) Before selecting a gear with the
engine running and the vehicle
stationary, fully depress the
brake pedal to prevent the
vehicle from creeping.
The vehicle will begin to move
as soon as the gear is engaged,
especially when the engine
speed is high, at fast idle or with
the air conditioning operating,
the brakes should only be
released when you are ready to
drive away.
(2) Depress the brake pedal with the
right foot at all times.
Using the left foot could cause
driver movement delay in case
of an emergency.
(3) To prevent sudden accelera-
tion, never race the engine when
shifting from the“P”(PARK) or
“N”(NEUTRAL).
CAUTION
(4) Operating the accelerator pedal
while the other foot is resting on
the brake pedal will affect brak-
ing efficiency and may cause
premature wear of brake pads.
Do not race the engine with
brake pedal pressed.
This can damage the transmis-
sion.Passing acceleration
EI04F-P
To gain extra acceleration in“D”(DRIVE)
position (when passing another vehicle)
push the accelerator to the floor. The auto-
matic transmission will automatically down-
shift.
NOTE
In sports mode, downshifts do not take
place when the accelerator is depressed all
the way to the floor.
Uphill/downhill driving
EI04O-Ia
DRIVING UPHILL
The transmission may not upshift to a
higher gear if the computer determines the
current speed cannot be maintained once
a higher gear is engaged.
For smoother vehicle performance, if you
release the throttle while climbing a steep
grade, the transmission may not upshift.
This is normal, as the computer is tempo-
rarily preventing shifting. After reaching the
top of the hill, normal gear shift function will
resume.
DRIVING DOWNHILL
When travelling down steep grades, the
computer may automatically select a lower
gear. This function assists engine brak-
ing efforts, reducing the need for using the
brakes.
Starting and driving
5-22Div:
Out put date:

Braking
EI23AAGa
All the parts of the brake system are criti-
cal to safety. Have the vehicle serviced by an
authorized MITSUBISHI dealer at regular
intervals according to the service booklet.Brake system(1) The service brake is divided into two
brake circuits so that when one brake
circuit fails, the other is available to stop
the vehicle. If this occurs, however, the
brake pedal must be depressed fur-
ther than usual; stop driving as soon as
possible and have the brake system
repaired at the nearest authorized
MITSUBISHI dealer.
(2) The brake boosting force is lost after
the brake pedal is depressed once or
twice while the engine is off. If this
occurs, the brake will require greater
force than usual. This is especially
important when the vehicle is being
towed.
Vehicles equipped with anti-lock brake
system
The brake system uses brake fluid pres-
surized by the pump to power-assist the
brake. If the brake system fails during driv-
ing, the brake warning lamp comes on and
buzzer sounds continuously. In this case,
the brake may not work properly.If this buzzer should continue to sound,
park your vehicle in a safe place and con-
tact your nearest authorized MITSUB-
ISHI dealer.
Please refer to“Brake warning lamp”on
page 4-7.
CAUTION
Bring the vehicle to halt in a safe
location by applying the brakes gen-
tly. Applying the brakes rapidly or
driving at high speed may make the
vehicle unstable.
NOTE
(1) Depressing the brake pedal repeat-
edly may turn on the brake warning
lamp, ABS warning lamp and brake
warning buzzer. It is normal if the lamp
goes out and the buzzer stops sound-
ing after a few seconds.
(2) In certain cases immediately after the
engine has been started or when the
brake pedal is depressed repeatedly, a
noise generated by operation of brake
devices may be heard coming from the
engine compartment. This type of noise
is normal and is no need for concern.
In fact, it indicates that the correspond-
ing devices are operating normal.
Warning lampThe brake warning lamp lets you know if
your brake system is working properly.
Read“Brake warning lamp”on page 4-7.When brakes are wetCheck the brake system while driving at a
low speed immediately after starting, espe-
cially when the brakes are wet, to con-
firm they work normally.
A film of water can form on the brake discs
and prevent normal functioning after driv-
ing in heavy rain or through large puddles,
or after the vehicle is washed. If this occurs,
dry the brakes out by driving slowly while
lightly depressing the brake pedal.When driving downhillIt is important to take advantage of the
engine braking by shifting to a lower gear
while driving on steep downhill roads in
order to prevent the brakes from overheat-
ing.
Starting and driving
5-44Div:
Out put date:

N28A172A
E LHD* RHD*E: 3200 models
*: Optional equipment
WARNING
(1) Be sure to observe the connect-
ing sequence of➀→➁→➂→➃.
(2) Make sure that the connection➃
is made to the appointed posi-
tion (shown in the illustration). If
the connection is made directly
to the negative side of the bat-
tery, the inflammable gases gen-
erated from the battery might
catch fire and explode.
(3)
When connecting the jumper
cable, do not connect the posi-
tive (+) cable to the negative (-)
terminal. Otherwise sparks may
cause explosion of the battery.
CAUTION
(1) Take care not to get the jumper
cable caught in the cooling fan
or other rotating part in the
engine compartment.
(2) Use the proper cables suitable
for the battery size.
Otherwise heat damage to the
cables could result.
(3) Check the jumper cables for
damage and corrosion before
use.
6. Start the engine in the vehicle which has
the booster battery, let the engine idle a
few minutes, then start the engine in the
vehicle with the discharged battery.
CAUTION
Keep running the engine of the
vehicle giving assistance.
7. After the engine is started, disconnect
the cables in the reverse order.
WARNING
(1) Charging the battery while it is
installed in the vehicle might
cause the battery to catch fire
and explode. Or damage to the
vehicle could result. If it has to
be charged in that condition for
unavoidable reasons, discon-
nect the vehicle side negative (-)
terminal connected to the bat-
tery.
(2) Keep sparks, cigarettes and
flames away from the battery
because the battery may pro-
duce an explosion.
(3) Use adequate ventilation when
charging or using the battery in
an enclosed space.
(4) Remove all the caps before
charging the battery.
(5) Electrolyte is corrosive diluted
sulphuric acid.
If electrolyte (battery acid)
comes into contact with your
hands, eyes, clothes or the
painted surface of your vehicle,
it should be thoroughly flushed
with water. If electrolyte gets in
your eyes, flush them with water
immediately and thoroughly, and
get prompt medical attention.
For emergencies
8-27
Div:
Out put date:

Other specifications
EP01IOE
Item 2500 models 3200 models 3500 models
Fuel systemCombustion typeIn-direct injection Direct Injection Gasoline Direct Injection
Fuel injection
pumpElectronically controlled Electric motor type
Clutch Dry single disc clutch with diaphragm spring, hydraulic action
Steering system Rack & pinion type, power assisted
SuspensionFront Independent type, double wishbone, coil spring
Rear Independent type, multi-link, coil spring
Service brakesType Hydraulic, front and rear split double circuit system with power assistance, anti-lock brake*
Front Ventilated disc brakes
Rear Drum in ventilated disc brakes
Parking brakes Parking brake acts mechanically on rear wheels
*: Optional equipment
Specifications
10-11
Div:
Out put date: