2003 FORD MUSTANG belt

z
Stage 3: Tighten an additional 60 degrees.
29. Install the belt idler pulleys.
30. Lubricate the engine front cover and the front oil seal inner lip with clean engine oil.
31. Using the special tool, install the front oil seal.
32. Install the coolant pump pulley and bolts. Klj . 12 ba
252003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

57. Install the accessory drive belt.
58. Install the radio interference capacitors.
59. Install the ignition coils and bolts.
60. Position the throttle body and install the bolts, tightening in the sequence shown. Klj . 20 ba
252003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

b
P=Primary, S=Secondary, E=Exhaust
c Time necessary for plunger to leak down 1.6 mm of travel with 222 N force and leak down fluid in
tappet.
Torque Specifications Description Nm lb-
ft lb-
in A/C compressor bolts 25 18 —
A/C peanut fittings 8 — 71
A/C muffler nut 25 18 —
Accelerator bracket bolts 10 — 89
Battery tray bolts 11 8 —
Belt idler support bracket assembly fasteners 25 18 —
Camshaft sprocket bolt 115 85 —
Coolant bypass tube studs 25 18 —
Coolant bypass tube bolts 25 18 —
Coolant hose and tube assembly bolt 25 18 —
Cooling fan motor and shroud bolts 10 — 89
Connecting rod bolt
a — — —
Engine front cover bolt a a a
Drive belt tensioner bolts 25 18 —
Cylinder head bolt
a — — —
Idler pulley bracket 25 18 —
Power steering pump bolts 25 18 —
Power steering hose fitting 65 48 —
Power steering hose bracket bolt 10 — 89
Pulley to crankshaft bolt
a — — —
EGR valve to intake manifold
a — — —
Engine coolant degas bottle bolts 10 — 89
Exhaust manifold studs 25 18 —
Generator bolts 25 18 —
Generator support bracket bolts 25 18 —
Hood prop bolt 10 — 89
Hood mounting nuts 12 9 —
Heater water inlet tube 10 — 89
Heater water outlet tube 24 18 —
Lower intake manifold-
to-cylinder head bolt a — — —
Main bearing cap bolt
a — — —
Oil filter adapter bolt 25 18 —
Oil bypass filter to adapter 50 37 —
Oil pump screen cover and tube-
to-oil pump bolt 10 — 89
Oil pan-to-
cylinder block bolt a — — — Klj . 4 ba
62003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

a
Refer to the procedure. Oil pan-to-
engine front cover bolts a — — —
Oil pump-
to-cylinder block bolt 10 — 89
Radio ignition interference capacitor bolts 25 18 —
Oil pump screen and pickup tube-
to-main bearing cap stud spacer bolt 25 18 —
Water pump pulley bolts 25 18 —
Throttle body spacer nuts 25 18 —
Vacuum accessory bracket fasteners 10 — 89
Valve cover bolt 10 — 89
Wiring harness support bracket 25 18 —
Water pump-
to-cylinder block bolt 25 18 —
EGR valve to exhaust manifold tube nuts 40 30 —
Power steering pump to engine 25 18 —
Power steering hose bracket nut 25 18 —
Power steering reservoir bracket fasteners 10 — 89
Supercharger degas bottle bolts 10 — 89
Camshaft cap cluster to cylinder head 10 — 89
Timing chain tensioner bolts—
primary 25 18 —
Timing chain tensioner bolts—
secondary 10 — 89
Ignition coil cover bolts 10 — 89
Generator mounting bracket retainers 10 — 89
Oil level indicator tube retainer 10 — 89
Primary timing chain guide-
to-engine bolts 10 — 89
Oil pump screen and pickup tube spacer to main bearing stud 25 18 —
Belt idler pulley bolt 25 18 —
Subframe brace nuts 41 30 — Klj . 5 ba
62003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

z
The inner rotor is piloted on the crankshaft post and is driven through flats on the crankshaft.
z System pressure is limited by an integral, internally- vented relief valve which directs the
bypassed oil back to the inlet side of the oil pump.
z Oil pump displacement has been selected to provide adequate volume to ensure correct oil
pressure both at hot idle and maximum speed.
z The relief valve calibration protects the system from excessive pressure during high viscosity
conditions.
z The relief valve is designed to provide adequate connecting rod bearing lubrication under high-
temperature and high- speed conditions.
Cooling System
The engine cooling system includes the following:
zradiator
z water pump
z the electric cooling fan motor and fan blade, activated by the variable control module
z the degas bottle, which aids in maintaining the correct volume of engine coolant
z water thermostat
z upper radiator hose
z lower radiator hose
z heater water hoses
Drive Belt System
The 4.6L (4V) DOHC engine is equipped with a serpentine drive belt. To ensure maximum life, a
replacement drive belt should be of the same type as originally installed.
zThe accessories mounted on the front of the engine are belt- driven by the crankshaft.
z The serpentine drive belt is routed over each accessory pulley, driven by the crankshaft pulley
bolted to the crankshaft.
For service procedures, including tensioning, refer to Section 303 - 05 . Klj . 3 ba
162003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

Item Part Number Description
1 N605904 Bolt
2 N620480 Nut
3 6A946 Cover
4 17K814 Alternator bracket assembly
5 N811268 Bolts (2 req'd)
6 8620 Accessory drive belt
7 N606543 Bolt (4 req'd)
8 6L266 Timing chain tensioner Klj . 7 ba
162003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

9 6268 Timing chain (2 req'd)
10 6M256 Timing chain guide
11 6L266 Timing chain tensioner
12 6L253 Timing chain tensioner arm
13 6268 Timing chain (2 req'd)
14 N804958 Bolt (2 req'd)
15 6B274 Timing chain guide
16 N606527 Bolt
17 19D269 A/C compressor
18 N806184 Bolts (3 req'd)
19 6306 Crankshaft sprocket
20 6L253 Timing chain tensioner arm
21 12A227 Ignition pulse ring
22 6C086 Engine front cover
23 N806177 Bolts (8 req'd)
24 N806300 Studs (5 req'd)
25 6700 Crankshaft front seal
26 6316 Crankshaft pulley
27 N806165 Washer
28 W701512 Stud
29 8A528 Water pump pulley
30 N806282 Bolts (4 req'd)
31 N806177 Bolts (4 req'd)
32 8501 Water pump
33 N808102 Bolt
34 19A216 Belt idler pulley
35 N804178 Nut
36 N806300 Harness support bracket
37 N806300 Stud
38 N806155 Bolt
39 6C315 Crankshaft position sensor
40 N806155 Bolt
41 6B288 Camshaft position sensor
42 N808920 Bolts (3 req'd)
43 6C254 Crankshaft extension support pulley
44 10153 Lower support bracket
45 N605909 Bolts (2 req'd)
46 8620 Accessory drive belt
47 N811268 Bolt
48 8B603 Belt idler bracket support
49 N808198 Stud
50 Klj . 8 ba
162003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

IN-
VEHICLE REPAIR
Lower Intake Manifold
Removal and Installation 1. Drain the engine coolant. For additional information, refer to Section 303 - 03A in this section.
2. Drain the supercharger coolant. For additional information, refer to Section 303 - 03B .
3. Release the fuel system pressure. For additional information, refer to Section 310 - 00 .
4. Disconnect the radiator upper hose, radiator lower hose and the supercharger degas hose.
5. Remove the supercharger belt. For additional information, refer to Section 303 - 05 .
6. Disconnect the coolant hose.
SECTION 303-
01C: Engine — Cobra 4.6L (4V) 2003 Mustang Workshop Manual Material
Item Specification
Motorcraft Premium Engine
Coolant
VC
-4-A (in Oregon VC- 5, in
Canada CXC- 10) (green color) ESE-
M97B44-
A Motorcraft Premium Gold
Engine Coolant
VC
-7-A (in Oregon VC-7- B)
(yellow color) WSS-
M97B51-
A1 Klj . 1 ba
72003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...