2003 FORD MUSTANG battery

B1408 Driver Power Window Up
Circuit Short to Battery GEM REFER to
Section 501 - 11 .
B1410 Driver Power Window Motor
Circuit Failure GEM REFER to
Section 501 - 11 .
B1426 Lamp Safety Belt Circuit
Short to Battery GEM REFER to
Section 413 - 01 .
B1428 Lamp Safety Belt Circuit
Failure GEM REFER to
Section 413 - 01 .
B1431 Wiper Brake/Run Relay
Circuit Failure GEM REFER to
Section 501 - 16 .
B1432 Wiper Brake/Run Relay
Circuit Short to Battery GEM REFER to
Section 501 - 16 .
B1434 Wiper Hi/Low Speed Relay
Coil Circuit Failure GEM REFER to
Section 501 - 16 .
B1436 Wiper Hi/Low Speed Relay
Coil Circuit Short to Battery GEM REFER to
Section 501 - 16 .
B1438 Wiper Mode Select Switch
Circuit Failure GEM REFER to
Section 501 - 16 .
B1441 Wiper Mode Select Switch
Circuit Short to Ground GEM REFER to
Section 501 - 16 .
B1446 Wiper Park Sense Circuit
Failure GEM REFER to
Section 501 - 16 .
B1448 Wiper Park Sense Circuit
Short to Battery GEM REFER to
Section 501 - 16 .
B1450 Wiper Wash/Delay Switch
Circuit Failure GEM REFER to
Section 501 - 16 .
B1453 Wiper Wash/Delay Switch
Circuit Short to Ground GEM REFER to
Section 501 - 16 .
B1458 Wiper Washer Pump Motor
Relay Circuit Failure GEM REFER to
Section 501 - 16 .
B1460 Wiper Washer Pump Motor
Relay Coil Circuit Short to Battery GEM REFER to
Section 501 - 16 .
B1462 Safety Belt Switch Circuit
Failure GEM REFER to
Section 413 - 09 .
B1466 Wiper Hi/Low Speed Not
Switching GEM REFER to
Section 501 - 16 .
B1473 Wiper Low Speed Circuit
Motor Failure GEM REFER to
Section 501 - 16 .
B1476 Wiper High Speed Circuit
Motor Failure GEM REFER to
Section 501 - 16 .
B1551 Decklid Release Circuit
Failure GEM REFER to
Section 501 - 14B .
B1553 Decklid Release Circuit
Short to Battery GEM REFER to
Section 501 - 14B .
B1555 Ignition Run/Start Circuit
Failure GEM REFER to
Section 211 - 05 .
B1687 Lamp Dome Input Circuit
Short to Battery GEM REFER to
Section 417 - 02 .
B2486 LF Side Repeater Lamp GEM REFER to
Section 417 - 01 . Klj . 4 ba
162003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

Symptom Chart
Pinpoint Tests
CAUTION: Before removing and installing the GEM or its connectors, disconnect the Output Circuit Failure
B2488 RF Side Repeater Lamp
Output Circuit Failure GEM REFER to
Section 417 - 01 .
C1189 Brake Fluid Level Sensor
Input Short Circuit to Ground GEM REFER to
Section 413 - 01 .
C1223 Lamp Brake Warning
Output Circuit Failure GEM REFER to
Section 413 - 01 .
C1225 Lamp Brake Warning
Output Circuit Short to
Battery GEM REFER to
Section 413 - 01 .
Symptom Chart Condition
Possible Sources Action
z No communication with the generic
electronic module z
CJB Fuse 39
(5A)
z GEM.
z Circuitry. z
GO to
Pinpoint Test A .
z The courtesy lamps are inoperative zCJB Fuse 7
(20A).
z Door ajar switch
(es).
z Courtesy lamp
assemblies.
z Circuitry.
z GEM.
z Ignition Switch.
z Headlamp
Switch. z
GO to
Pinpoint Test B .
z The demand lighting is inoperative zCJB Fuse 7
(20A).
z Circuitry.
z GEM.
z Door ajar switch
(es).
z Demand lamp
assemblies.
z Ignition Switch.
z Headlamp
Switch. z
GO to
Pinpoint Test C .
z The illuminated entry is inoperative
when using the remote transmitter z
Remote
transmitter.
z GEM. z
GO to
Pinpoint Test D .
z The battery saver does not
deactivate after timeout z
Circuitry.
z GEM. z
GO to
Pinpoint Test E . Klj . 5 ba
162003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

battery. Failure to follow this caution will result in the GEM storing many erroneous DTCs and
may result in the GEM exhibiting erratic operation after installation.
CAUTION: Be careful when probing the central junction box (CJB), battery junction box
(BJB), or any connectors. Damage will result to the connector receptacle if the probe being
used is too large.
CAUTION: Electronic modules are sensitive to static electrical charges. If exposed to
these charges, damage may result.
NOTE: If continuous DTCs are recorded and the symptom is not present when carrying out the
pinpoint tests, an intermittent concern may be the cause. Always check for loose connections and
corroded terminals.
NOTE: Complete the entire pinpoint test related to the symptom before installing a new GEM.
PINPOINT TEST A: NO COMMUNICATION WITH THE GENERIC
ELECTRONIC MODULE Test Step Result / Action to Take
CAUTION: Use the correct probe adapter(s) when making measurements. Failure to
use the correct probe adapter(s) may damage the connector. A1 GENERIC ELECTRONIC MODULE (GEM) POWER SUPPLY
z
Key in OFF position.
z Disconnect: Generic Electronic Module (GEM) C201a.
z Disconnect: GEM C201b.
z Key in ON position.
z Using the following table, measure the voltage between the
GEM, harness side and ground.
z Are the voltages greater than 10 volts? Connector Pin Circuit
C201a 2 400 (LB/BK)
C201a 3 1006 (DG/WH)
C201b 1 1001 (WH/YE)
C201b 4 193 (YE/LG) Yes
GO to
A2 .
No
REPAIR the circuit(s) in
question. TEST the system
for normal operation. A2 CHECK THE GEM GROUND CIRCUIT 397 (BK/WH) FOR
OPEN z
Key in OFF position.
z Measure the reistance between the GEM C201b pin 2, circuit
397 (BK/WH), harness side and ground. Yes
GO to
A3 .
No
REPAIR the circuit(s) in
question. TEST the system
for normal operation. Klj . 6 ba
162003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

z
Monitor the GEM PID DECKLID, while opening and closing
the luggage compartment lid.
z Does the GEM PID DECKLID agree with the dome switch
position? Yes
GO to
B5 .
No
GO to B16 .
B5 CHECK THE COURTESY LAMP CIRCUITS
z
Close the luggage compartment lid and all doors are closed.
z Turn the dome and map lamp switches to the off position.
z Are the courtesy lamps illuminated? Yes
GO to
B12 .
No
GO to B6 .
B6 CHECK THE GEM CONTROL OF THE COURTESY LAMPS
z
Trigger the GEM active command COURTESYL ON and then
OFF.
z Do the courtesy lamps illuminate when the GEM active
command COURTESYL ON is triggered, and go out when
the GEM active command COURTESYL OFF is triggered? Yes
INSTALL a new GEM. For
additional information,
REFER to
Section 419 -
10 . REPEAT the self-
test.
CLEAR the DTCs.
No
GO to B7 .
B7 CHECK THE GEM FOR AN INTERNAL FAULT
z
Trigger the GEM active command COURTESYL ON, then
OFF.
z Can an audible click be heard coming from the GEM,
while triggering the active command COURTESYL ON? Yes
GO to
B8 .
No
INSTALL a new GEM. For
additional information,
REFER to Section 419 -
10 . REPEAT the self-
test.
CLEAR the DTCs. B8 CHECK CIRCUIT 1034 (BK/WH) FOR VOLTAGE
z
Disconnect the dome lamp C929 (coupe) or map lamp C978
(convertible)
z Trigger the GEM active command COURTESYL ON.
z Measure the voltage between dome/map lamp C929 (coupe)
Pin 3 or map lamp C978 (convertible) Pin 4, Circuit 1034
(BK/WH), harness side and ground.
z Is the voltage greater than 10 volts? Yes
GO to
B11 .
No
GO to B9 .
B9 CHECK CIRCUIT 1006 (DG/WH) FOR OPEN
NOTE:
Verify battery voltage at CJB Fuse 7 (20A) before
carrying out this test.
z Disconnect: GEM C201a.
z Measure the voltage between GEM C201a Pin 1, Circuit 1006
(DG/WH), harness side and ground. Yes
GO to
B10 .
No
REPAIR the circuit.
REPEAT the self- test.
CLEAR the DTCs. Klj . 8 ba
162003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

z
Is the voltage greater than 10 volts? B10 CHECK CIRCUIT 1034 (BK/WH) FOR OPEN
z
Disconnect: GEM C201c.
z Measure the resistance between GEM C201c Pin 3, Circuit
1034 (BK/WH), harness side and dome/map lamp C929
(coupe) Pin 3 or map lamp C978 (convertible) Pin 4, Circuit
1034 (BK/WH), harness side.
z Is the resistance less than 5 ohms? Yes
INSTALL a new GEM. For
additional information,
REFER to
Section 419 -
10 . REPEAT the self-
test.
CLEAR the DTCs.
No
REPAIR the circuit.
REPEAT the self- test.
CLEAR the DTCs. B11 CHECK CIRCUIT 1205 (BK) FOR OPEN
z
Measure the resistance between dome/map lamp C929
(coupe) Pin 2 or map lamp C978 (convertible) Pin 1, Circuit
1205 (BK), harness side and ground.
z Is the resistance less than 5 ohms? Yes
INSTALL a new
dome/map lamp
assembly. For additional
information, REFER to
Lamp Assembly
—
Map/Dome .
No
REPAIR the circuit.
REPEAT the self- test.
CLEAR the DTCs. B12 CHECK CIRCUIT 1034 (BK/WH) FOR SHORT TO BATTERY
z
Measure the voltage between GEM C201c Pin 3, Circuit 1034
(BK/WH), harness side and ground. Yes
REPAIR the circuit.
REPEAT the self-
test.
CLEAR the DTCs.
No
INSTALL a new GEM. For
additional information,
REFER to Section 419 -
10 . REPEAT the self-
test.
CLEAR the DTCs. Klj . 9 ba
162003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

z
Is the voltage greater than 10 volts? B13 CHECK THE COURTESY LAMP OPERATION —
MONITOR
THE GEM PID DOMESW z
Monitor the GEM PID DOMESW, while moving the interior
lamp switch from the OFF to the ON position.
z Does the GEM PID DOMESW value always indicate ON? Yes
GO to
B15 .
No
GO to B14 .
B14 CHECK CIRCUIT 706 (GY) FOR OPEN
z
Disconnect: GEM C201e.
z Measure the voltage between GEM C201e Pin 21, Circuit 706
(GY), harness side and ground.
z Is the voltage greater than 10 volts? Yes
INSTALL a new GEM. For
additional information,
REFER to
Section 419 -
10 . REPEAT the self-
test.
CLEAR the DTCs.
No
REPAIR the circuit.
REPEAT the self- test.
CLEAR the DTCs. B15 CHECK CIRCUIT 706 (GY) FOR SHORT TO BATTERY
z
Measure the voltage between GEM C201e Pin 21, Circuit 706
(GY), harness side and ground.
z Is the voltage greater than 10 volts? Yes
REPAIR the circuit.
REPEAT the self-
test.
CLEAR the DTCs.
No
INSTALL a new GEM. For
additional information,
REFER to Section 419 -
10 . REPEAT the self-
test.
CLEAR the DTCs. B16 CHECK CIRCUIT 486 (BN/WH) FOR OPEN OR SHORT TO
GROUND — MONITOR THE GEM PID DECKLID z
Monitor the GEM PID DECKLID, while opening and closing
the luggage compartment lid.
z Does the GEM PID DECKLID agree with the luggage
compartment lid position? Yes
GO to
B17 .
No
GO to B19 . Klj . 10 ba
162003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

C4 CHECK INTERIOR LAMP SWITCH INPUT TO THE GEM —
MONITOR GEM PID DOMESW z
Monitor the GEM PID DOMESW, while moving the interior
lamp switch from the OFF to the ON position.
z Does the GEM PID DOMESW values agree with the
interior lamp switch positions? Yes
GO to
C5 .
No
GO to Pinpoint Test B .
C5 CHECK THE LUGGAGE COMPARTMENT LID AJAR INPUT
TO THE GEM — MONITOR THE GEM PID DECKLID z
Monitor the GEM PID DECKLID, while opening, and closing,
the luggage compartment lid.
z Does the GEM PID DECKLID agree with the luggage
compartment lid position? Yes
GO to
C6 .
No
GO to Pinpoint Test B .
C6 CHECK CIRCUIT 705 (LG/OG) FOR OPEN
z
Turn on both map lamps using the switches in the rear view
mirror.
z Turn on both vanity mirror lamps.
z Open the luggage compartment lid.
z Disconnect: GEM C201c.
z Connect a fused jumper (20A) between GEM C201c Pin 4,
Circuit 705 (LG/OG), harness side and battery positive
terminal.
z Do the demand lamps illuminate? Yes
GO to
C7 .
No
REPAIR the circuit.
REPEAT the self- test.
CLEAR the DTCs. C7 CHECK CIRCUIT 1006 (DG/WH) FOR OPEN
NOTE:
Verify battery voltage at CJB Fuse 7 (20A) before
carrying out this test.
z Disconnect: GEM C201a.
z Measure the voltage between GEM C201a Pin 1, Circuit 1006
(DG/WH), harness side and ground.
z Is the voltage greater than 10 volts? Yes
INSTALL a new GEM. For
additional information,
REFER to
Section 419 -
10 . REPEAT the self-
test.
CLEAR the DTCs.
No
REPAIR the circuit.
REPEAT the self- test.
CLEAR the DTCs. C8 CHECK CIRCUIT 705 (LG/OG) FOR VOLTAGE AT
INOPERATIVE DEMAND LAMP z
Key in OFF position.
z Disconnect inoperative demand lamp, dome/map C929 Yes
GO to
C9 . Klj . 13 ba
162003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

PINPOINT TEST E: THE BATTERY SAVER DOES NOT DEACTIVATE
AFTER TIMEOUT
Test Step Result / Action to Take
E1 CHECK THE GEM CONTROL OF THE BATTERY SAVER
FUNCTION — TRIGGER THE GEM ACTIVE COMMAND BATT
SAVR ON z
Trigger the GEM active command BATT SAVR ON and then
OFF.
z Do the courtesy lamps illuminate and turn off when the
GEM active command BATT SAVR is triggered ON and
OFF? Yes
INSTALL a new GEM.
For additional
information, REFER to
Section 419
- 10 .
REPEAT the self- test.
CLEAR the DTCs.
No
GO to E2 .
E2 CHECK CIRCUITS 1034 (BK/WH), AND 705 (LG/OG), FOR
SHORT TO BATTERY z
Disconnect: GEM C201c.
z Measure the voltage between GEM C292 Pin 3, Circuit 1034
(BK/WH), harness side and ground; and between GEM C292
Pin 4, Circuit 705 (LG/OG), harness side and ground.
z Is the voltage greater than 10 volts? Yes
REPAIR the circuit in
question. REPEAT the
self-
test. CLEAR the
DTCs.
No
INSTALL a new GEM.
For additional
information, REFER to
Section 419 - 10 .
REPEAT the self- test.
CLEAR the DTCs. Klj . 15 ba
162003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...