2003 FORD MUSTANG flat tire

z
wheel bearing life.
z brake cooling.
New wheels need to be installed when vehicle's wheels:
zare bent.
z are cracked.
z are dented.
z are heavily corroded.
z are leaking.
z have elongated wheel hub bolt holes.
z have excessive lateral or radial runout.
Wheel and tire assemblies are attached by six wheel nuts.
It is mandatory to use only the tire sizes recommended on the tire chart attached to the vehicle. Larger
or smaller tires can damage the vehicle, affect durability, and require changing the speedometer
calibration. Make sure wheel size and offsets match those recommended for the tire in use. 1. Inspect for signs of uneven wear that may indicate a need for balancing, rotation, front suspension alignment, damaged tie- rod, or steering components.
2. Check tires for: zcuts.
z stone bruises.
z abrasions
z blisters.
z embedded objects.
3. Tread wear indicators are molded into the bottom of the tread grooves. Install a new tire when the indicator bands become visible.
Symptom Chart Symptom Chart Condition
Possible Sources Action
z Tires show
excess wear on
edge of tread z
Underinflated tires. zADJUST air pressure
in tires.
z Vehicle overloaded. zRETURN vehicle.
NOTIFY customer of
overload condition.
z High- speed cornering. zRETURN vehicle.
NOTIFY customer of
cause of condition.
z Incorrect ride height. zSET ride height.
z Incorrect wheel alignment. zSET alignment to
specification. REFER Klj . 2 ba
42003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

to
Section 204 - 00 .
z Incorrect tire rotation
intervals. z
ADVISE customer of
condition. ROTATE
tires.
z Tires show
excess wear in
center of tread z
Tires overinflated. zADJUST air pressure.
z Other excessive
tire wear
problems z
Incorrect tire rotation
intervals. z
ADVISE customer of
condition. ROTATE
tires.
z Incorrect tire pressure. zADJUST pressure.
z Loose or leaking shock
absorbers. z
TIGHTEN or INSTALL
new shock absorbers
as necessary.
z Incorrect wheel alignment. zSET alignment to
specification. REFER
to Section 204 - 00 .
z Loose, worn or damaged
suspension components. z
REFER to Section 204 - 00 .
z Wheel and tire assembly
out of balance. z
BALANCE wheel and
tire assembly.
z Excessive lateral or radial
runout of wheel. z
REFER to Section 100 - 04 .
z Wobble or
shimmy z
Damaged wheel bearings. zREFER to Section 204 - 00 .
z Loose or damaged
suspension components. z
REFER to Section 204 - 00 .
z Bent wheel. zINSTALL a new wheel
as necessary.
z Damaged tire. zINSTALL a new tire as
necessary.
z Loose wheel nuts. zTIGHTEN to
specification.
z High- speed
shake z
Wheel hub face/pilot/bolt
circle runout.
z Tires/wheels.
z Wheel bearings.
z Suspension/steering
linkage.
z Engine.
z Transmission.
z Brake discs/imbalance. z
REFER to Section 100 - 04 .
z Vehicle vibration zDriveline — engine.
z Tires. z
REFER to Section 100 - 04 . Klj . 3 ba
42003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

GENERAL PROCEDURES
Wheel Leaks
WARNING: Wheel repairs that use welding or peening are not approved. An inner tube is
not an acceptable repair for leaking wheels or tires.
If the air pressure in a tire mounted on an aluminum wheel is found to be low, perform the
following procedure before considering installation of a new wheel.
1. Remove the tire and wheel assembly, and inspect the wheel for structural damage. If none exists, go to Step 2. If the wheel is damaged, install a new wheel.
2. With the tire mounted on the wheel, locate the air leak using a water bath or equivalent method, and mark the location. Check the complete wheel for possible additional leaks. When leaks are
marked, dismount the tire marking valve location on the tire for correct indexing.
3. On the tire side of the wheel, thoroughly clean the leaking area with an appropriate choke cleaner or use sandpaper of approximately 80- grit to remove all contamination. Using the
sandpaper, score the surface of the leaking area to improve adhesion of the sealer. If the valve
stem is close to the area, remove it.
4. Use a clean cloth to remove all cleaner or sanding dust.
5. NOTE: Do not use a torch containing oxyacetylene.
Heat the prepared area with a Heat Gun or a propane torch until aluminum wheel repair
compound flows. Apply the hot melt material over the prepared area using a liberal flow and
wiping action. Repair is most effective when heat is applied to the brake side of the rim, and the
sealer is melted by heat in the metal.
6. Apply only enough heat to melt the sealer, then remove the heat source. After repairing the leak, allow the wheel to cool until it can be handled safety.
7. CAUTION: Use caution when mounting the tire so as not to damage the sealer.
Index and assemble the tire and wheel. Inflate the tire to the recommended pressure as
indicated on the tire pressure decal.
8. Repeat Step 2 to verify repair.
9. When the repair is completed, balance the assembly and install it on the vehicle.
SECTION 204-
04: Wheels and Tires 2003 Mustang Workshop Manual Material
Item Specification
Professional Choke and
Linkage Cleaner
F8AZ-
19520- AB WSS-
M14P10-
B Aluminum Wheel Repair
Compound ESA-
M4G280-
A Klj . 1 ba
22003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

Component Tests
Driveline Vibration
An analysis of driveline vibration can also be conducted using the Vibration Analyzer; follow the
manufacturer's directions.
Driveline vibration exhibits a higher frequency and lower amplitude than does high-
speed shake.
Driveline vibration is directly related to the speed of the vehicle and is usually noticed at various speed
ranges. Driveline vibration can be perceived as a tremor in the floorpan or is heard as a rumble, hum,
or boom. Driveline vibration can exist in all drive modes, but may exhibit different symptoms depending
upon whether the vehicle is accelerating, decelerating, floating, or coasting. Check the driveline angles
if the vibration is particularly noticeable during acceleration or deceleration, especially at lower speeds.
Driveline vibration can be duplicated by supporting the axle upon a hoist or upon jack stands, though
the brakes may need to be applied lightly in order to simulate road resistance.
1. Raise the vehicle promptly after road testing. Use a twin- post hoist or jack stands to prevent tire
flat- spotting. Engage the drivetrain and accelerate to the observed road test speed to verify the lubricant type.
205 - 02B . CLEAN and
REFILL the axle to
specification.
z Axle overheating zLubricant level too
low. z
CHECK the lubricant level.
FILL the axle to specification.
z Incorrect or
contaminated
lubricant type. z
INSPECT the axle for
damage. REPAIR as
necessary. CLEAN and
REFILL the axle to
specification.
z Bearing preload
adjusted too tight. z
CHECK the ring and pinion for
damage. INSPECT the ring
and pinion wear pattern.
ADJUST the preload as
necessary.
z Excessive gear
wear. z
INSPECT all the axle gears
for wear or damage. INSTALL
new components as
necessary.
z Incorrect ring gear
backlash. z
INSPECT the ring gear for
scoring. INSPECT the ring
and pinion wear pattern.
ADJUST the ring gear
backlash as necessary.
z Broken gear teeth
on the ring gear
or pinion z
Overloading the
vehicle. z
INSTALL a new ring and
pinion. REFER to Section 205 - 02A or
Section 205 - 02B .
z Axle shaft broken zOverloading the
vehicle. z
INSTALL a new axle shaft.
REFER to Section 205 - 02A or
Section 205 - 02B .
z Misaligned axle
shaft tube. z
INSPECT the axle for
damage. CHECK axle shaft
tube alignment. INSTALL a
new axle shaft. REFER to
Section 205 - 02A or
Section 205 - 02B . Klj . 11 ba
192003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

9. If an obvious cause for an observed or reported malfunction is found, correct the cause (if
possible) before proceeding to the next step.
10. If the fault is not visually evident, determine the symptom and proceed to the following symptom chart.
Steering System Symptom Definitions
Drift/Pull
Pull is a tugging sensation, felt by the hands on the steering wheel, that must be overcome to keep the
vehicle going straight.
Drift describes what a vehicle with this condition does with hands off the steering wheel.
zA vehicle-related drift/pull, on a flat road, will cause a consistent deviation from the straight-
ahead path and require constant steering input in the opposite direction to counteract the effect.
z Drift/pull may be induced by conditions external to the vehicle (i.e., wind, road camber).
Excessive Steering Wheel Play
Excessive steering wheel play is a condition in which there is too much steering wheel movement
before the wheels move. A small amount of steering wheel free play is considered normal.
Feedback
Feedback is a roughness felt in the steering wheel when the vehicle is driven over rough pavement.
Hard Steering or Lack of Assist
Hard steering or lack of assist is experienced when the steering wheel effort exceeds specifications.
Hard steering can remain constant through the full turn or occur near the end of a turn. It is important
to know the difference between hard steering/lack of assist and binding.
Hard steering or lack of assist can result from either hydraulic or mechanical conditions. It is extremely
important to know if this concern occurs during driving, during very heavy or static parking maneuvers.
Nibble
Sometimes confused with shimmy, nibble is a condition resulting from tire interaction with various road
surfaces and observed by the driver as small rotational oscillations of the steering wheel. Poor Returnability/Sticky Steering Visual Inspection Chart
Mechanical
z
Loose tie- rod ends
z Loose suspension components
z Loose steering column shaft universal joints
z Loose column intermediate shaft bolts
z Steering gear
z Binding or misaligned steering column
z Power steering pump
z Bent or pinched power steering hoses Klj . 4 ba
112003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

z
are connected in series with the fuel pressure sensor.
z supply fuel from the fuel tank with a fuel pump mounted in the fuel tank.
A constant fuel pressure drop is maintained across the fuel injectors by the fuel pressure sensor. The
fuel pressure sensor:
zis positioned upstream from the fuel injectors on the fuel injection supply manifold.
Valve Train
The valve train operates as follows:
zball- tip hydraulic lash adjusters provide automatic lash adjustment.
z roller followers ride on the camshaft lobes, transferring the up-and- down motion of the
camshafts to the valves in the cylinder heads.
Positive Crankcase Ventilation System
All engines are equipped with a closed- type positive crankcase ventilation system recycling the
crankcase vapors to the upper intake manifold.
Lubrication System
The engine lubrication system operates as follows:
zoil is drawn into the oil pump through the oil pump screen cover and tube in the sump of the oil
pan.
z oil is pumped through the oil bypass filter on the left front side of the cylinder block.
z oil enters the main oil gallery where it is distributed to the crankshaft main journals and to both
cylinder heads.
z From the main journals, the oil is routed through cross- drilled passages in the crankshaft to
lubricate the connecting rod bearings. Controlled leakage through the crankshaft main bearings
and connecting rod bearings is slung radially outward to cool and lubricate the cylinder walls as
well as the entire connecting rod, piston and piston rings assembly.
z The left cylinder head is fed from a drilling into the supply passage feeding the main gallery at
the front of the cylinder block. The right cylinder head is fed from a drilling into the rear of the
main gallery. Main gallery pressure is reduced as it enters the cylinder head galleries through
fixed serviceable orifices located at the upper part of the feed passages. It is this reduced
pressure in the cylinder head galleries which feeds the camshaft journals, the hydraulic lash
adjusters and the primary and secondary timing chain tensioners.
z The camshaft lobe and roller followers are lubricated by splash created through valve train
operation.
Oil Pump
The lubrication system of the 4.6L (4V) engine is designed to provide optimum oil flow to critical
components of the engine through its entire operating range. The heart of the system is a positive
displacement internal gear oil pump using top seal rotors. Generically this design is known as a gerotor
pump, which operates as follows.
zThe oil pump is mounted on the front face of the cylinder block.
z The inner rotor is piloted on the crankshaft post and is driven through flats on the crankshaft. Klj . 2 ba
152003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

9. Remove the third gear needle bearing.
zInspect the needle bearing for wear or damage. Install a new needle bearing as
necessary.
10. NOTE: Install the special tool with the flat side facing the bearing.
Using the special tool, press the output shaft front bearing from the output shaft.
11. Inspect the synchronizers. zCheck for worn, nicked or broken teeth. Install a new synchronizer as necessary.
z Check keys for wear or distortion. Install a new synchronizer as necessary.
z Check springs for distortion. Install a new synchronizer as necessary.
12. Inspect the synchronizer blocking rings. zCheck for wear or damage. Install new synchronizer blocking rings as necessary.
z Check the clearance between the synchronizer blocking ring and the gear.
„Position the blocking ring onto the gear. Make sure the correct blocking ring is
measured with the correct gear and that the blocking ring is fully seated on the
gear.
„ Insert a feeler gauge and measure the clearance, while applying pressure and
rotating the blocking ring. The measurement should be the same around the entire
circumference. If the clearance is less than 0.38 mm (0.015 in), install new
blocking rings. Klj . 6 ba
122003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_2308/S3B~us~en~ ...

GENERAL PROCEDURES
Headlamp Adjustment
Headlamp Aiming
1. The headlamp aiming procedure depends on the type of beam pattern the headlamp is equipped with. Vehicles may come equipped with visual optical right (VOR), visual optical left
(VOL), or SAE only (includes sealed beam type) headlamps. To identify the headlamp beam
pattern, look on the headlamp lens. Molded in small letters on the headlamp lens is one of the
following:
zSAE
z VOR or SAE
z VOL or SAE
2. Once the headlamp beam pattern is identified, aim the headlamps using one of the following methods as applicable.
zPhotometric aimers can aim SAE, VOR and VOL type headlamps. This is the preferred
method of headlamp aiming.
z Visual or screen method aiming can be used to aim SAE, VOR and VOL type
headlamps.
z Mechanical aimers can be used only with SAE type headlamps. Lamps that can be
aimed mechanically will have three nibs molded into the lens of the lamp.
Photometric Aiming 1. For the photometric aiming procedure, refer to the appropriate photometric headlamp aimer instruction manual.
Screen Method Aiming
All headlamp types
NOTE: Horizontal aim is not necessary for VOR or VOL headlamps.
NOTE: Consult your state vehicle inspection manual for recommended tolerance ranges for visual
aiming.
NOTE: The sight shield may need to be positioned or removed for access to the adjusters.
1. Before starting headlamp adjustment: zCheck the tire inflation.
z Check that no other load is in the vehicle other than a half tank of fuel.
z Check that the headlamps are clean.
z Check for correct headlamp operation.
SECTION 417-
01: Exterior Lighting 2003 Mustang Workshop Manual Klj . 1 ba
42003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...