2003 FORD MUSTANG change wheel

DESCRIPTION AND OPERATION
Rear Drive Halfshafts
The rear wheel drive halfshaft system consists of and operates as follows:
zHalfshafts (4K138) transmit engine torque from the rear axle housing to the rear wheels.
z Halfshafts rotate at approximately one- third the speed of a driveshaft and do not contribute to
rotational vibration disturbances.
z A constant velocity (CV) joint is a mechanism for transmitting uniform torque and rotary motion
while operating through a range of angles.
z CV joints at both inboard (differential) and outboard (wheel) ends provide operating
smoothness.
z The inboard CV joints are plunge- type joints that provide the axial movement necessary to
affect shaft length changes.
z The outboard CV joints have a higher angle capability than the inboard CV joints to
accommodate suspension travel.
z Inboard and outboard CV joints connect to a splined shaft.
z A driveshaft bearing retainer circlip retains the splined inboard CV joint to the differential side
gear. Install a new circlip every time you remove the halfshaft from the vehicle.
z A rear axle wheel hub retainer secures the interconnecting shaft and outboard CV joint to the
rear hub.
z The lubed-for- life CV joints use special CV joint grease. They require no periodic lubrication.
z To separate the halfshaft from the rear hub, press the outboard CV joint from the rear hub.
z To separate the halfshaft from the differential, apply a load to the back face of the inboard CV
joint assembly to overcome the circlip.
z The halfshaft assemblies are not repairable. Install a new assembly if worn/damaged.
SECTION 205-
05: Rear Drive Halfshafts 2003 Mustang Workshop Manual Klj . 1 ba
32003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

DIAGNOSIS AND TESTING
Brake System
Refer to Wiring Diagrams Cell
60 , Instrument Cluster for schematic and connector information.
Refer to Wiring Diagrams Cell 97 , Daytime Running Lamps for schematic and connector information.
Inspection and Verification WARNING: Use of any other than the approved DOT 3 brake fluid will cause permanent
damage to brake components and will render the brakes inoperative.
WARNING: Brake fluid contains polyglycol ethers and polyglycols. Avoid contact with
eyes. Wash hands thoroughly after handling. If brake fluid contacts eyes, flush eyes with
running water for 15 minutes. Get medical attention if irritation persists. If taken internally,
drink water and induce vomiting. Get medical attention immediately.
CAUTION: Do not spill brake fluid onto painted surfaces. If spilled, wipe up immediately.
NOTE: Always check the fluid level in the brake master cylinder reservoir (2K478) before performing
the test procedures. If the fluid level is not at the correct level, add High Performance DOT 3 Brake
Fluid C6AZ- 19542-AB or equivalent DOT 3 fluid meeting Ford specification ESA- M6C25-A.
NOTE: Prior to performing any diagnosis, make sure the brake warning indicator is functional. For
additional information, refer to Section 413 - 01 .
The first indication that something may be wrong in the brake system is a change in the feeling through
the brake pedal (2455). The brake warning indicator in the instrument cluster and the brake fluid level SECTION 206-
00: Brake System — General Information 2003 Mustang Workshop Manual Special Tool(s)
73 Digital Multimeter
105-
R0051 or Equivalent ABS Brake and Pressure Test
Kit
107-
02350 or Equivalent Tire and Wheel Runout Gauge
Set
134-
00199 or Equivalent Klj . 1 ba
152003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

in the brake master cylinder reservoir are also indicators of system concerns.
If a wheel is locked and the vehicle must be moved, open a bleeder screw at the locked wheel (1007)
to let out enough fluid to relieve the pressure. Close the bleeder screw. This bleeding operation may
release the brakes but will not correct the cause of trouble. If this does not relieve the locked wheel
condition, repair the locked components before proceeding.
Inspect all hoses and connections. All unused vacuum connectors should be capped. Make sure
hoses and their connections are correctly secured and in good condition with no holes, soft or
collapsed areas.
Non-
Pressure Leaks
The only part of the brake system that could have a brake fluid loss that does not appear when the
system is under pressure is the brake master cylinder reservoir area. Brake fluid loss can be caused
by a missing or poorly- fitted brake master cylinder filler cap (2162), a punctured or otherwise damaged
brake master cylinder reservoir, a missing or damaged brake master cylinder filler cap gasket, or by
missing, damaged or poorly- fitted sealing grommets between the brake master cylinder (2140) and the
brake master cylinder reservoir.
The brake master cylinder reservoir grommets are not separately serviceable and must be installed
new as part of a new brake master cylinder reservoir.
Install a new flexible brake hose if it shows signs of softening, cracking or other damage.
When installing a new brake hose, position the hose to avoid contact with other vehicle components.
Road Test
Perform a road test to compare actual vehicle braking performance with the performance standards
expected by the driver. The ability of the test driver to make valid comparisons and detect performance
deficiencies will depend on experience.
The driver should have a thorough knowledge of brake system operation and accepted general
performance guidelines in order to make good comparisons and detect performance problems.
Select a road that is reasonably smooth and level. Gravel or bumpy roads are not suitable because the
surface does not allow the tires to grip the road equally. Avoid crowned roads.
A key factor in evaluating brake concerns is the deceleration rate. This varies from vehicle to vehicle
and with changes in operating conditions. It is evident how well the brakes are working after just a few
applications.
Avoid locking the brakes. Locked brakes are not an indication of braking efficiency.
Visual Inspection Chart Mechanical Electrical
z
Brake master cylinder
z Brake caliper piston
z Brake discs
z Brake pads z
Parking brake switch
z Damaged or corroded wiring harness
z Brake master cylinder fluid level switch Klj . 2 ba
152003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

11. Turn (or have an assistant turn) the steering wheel slightly in both directions and release quickly
while watching the pressure gauge.
zThe pressure reading should move from the normal back pressure reading and snap
back as the steering wheel is released.
z If the pressure returns slowly or sticks, the rotary valve in the steering gear is sticking or
the steering column is binding. Check the steering column and linkages before servicing
the steering gear.
Tie- Rod Articulation Torque
1. NOTE: This check may be done with the steering gear on or off the vehicle.
Disconnect the tie- rod end from the front wheel spindle. For additional information, refer to
Section 211 - 02 .
2. Move the front wheel spindle tie- rod back and forth three times.
3. Hook the special tool 211- 034 (T74P-3504-Y) over the tie-rod end or the threaded portion of the
front wheel spindle tie- rod and measure the force required to move the front wheel spindle tie-
rod. Refer to Tie- Rod Articulation Torque in General Specifications in this section.
4. If the force required to move the front wheel spindle tie- rod does not meet the specifications,
install a new front wheel spindle tie- rod. For additional information, refer to Section 211 - 02 .
Steering Gear Valve 1. With the vehicle in motion, place the transmission in NEUTRAL and turn the engine OFF. zIf the vehicle does not pull with the engine OFF, install a new steering gear. For
additional information, refer to Section 211 - 02 .
2. If the vehicle pulls with the engine OFF, cross- switch the front wheels.
3. If the vehicle pulls to the opposite side, cross- switch the front and rear wheels on the same side.
4. If the vehicle pull direction does not change, check the front suspension components, wheel alignment and frame alignment. For additional information, refer to Section 204 - 00 or frame
dimensions manual. Klj . 10 ba
112003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

DESCRIPTION AND OPERATION
Engine Ignition
The ignition coil (12029), which is mounted on the upper intake manifold, can be described as a coil
pack containing three separate coil units. Each coil unit is individually controlled by the powertrain
control module (PCM) (12A650) through separate wire leads. Each coil unit activates two spark plugs
wired in a series by the spark plug wires (12286).
zOne spark plug activates on the compression stroke and uses the majority of the ignition coil's
stored energy.
z The other spark plug activates on the exhaust stroke and uses very little of the ignition coil's
stored energy.
z Because the pairs of spark plugs are connected in a series, one spark will travel from ground to
the electrode while the other spark will travel from the electrode to ground.
The spark plug (12405):
zchanges the high voltage pulse into a spark which ignites the fuel and air mixture.
z originally equipped on the vehicle has a platinum- enhanced active electrode for long life.
The crankshaft position (CKP) sensor (6C315):
NOTE: Initial engine ignition timing is set at 10 degrees ± 2 degrees before top dead center (BTDC)
and is not adjustable.
zis a variable reluctance sensor triggered by a 36- minus-1 tooth trigger pulse wheel located on
the crankshaft (6303) inside the engine front cover (6019).
The sine wave type signal generated from the crankshaft position sensor provides two types of
information:
zposition of the crankshaft in 10 degree increments
z the crankshaft speed (rpm)
The powertrain control module (PCM) (12A650) uses this information to determine ignition coil turn ON
and turn OFF times and misfire detection.
For additional information, refer to Section 303 - 14 .
SECTION 303-
07A: Engine Ignition — 3.8L 2003 Mustang Workshop Manual Klj . 1 ba
22003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

DESCRIPTION AND OPERATION
Engine Ignition
Eight separate ignition coils (12029):
zare mounted directly above each spark plug (12405).
z are controlled by the powertrain control module (PCM) for correct firing sequence.
The spark plug:
zchanges the high voltage pulse into a spark which ignites the fuel and air mixture.
z originally equipped on the vehicle has a platinum- enhanced active electrode for long life.
Crankshaft position (CKP) sensor (6C315):
NOTE: Initial engine ignition timing is set at 10 degrees ± 2 degrees before top dead center (BTDC)
and is not adjustable. For additional information, refer to the Powertrain Control/Emissions Diagnosis
(PC/ED) manual.
zis a variable reluctance sensor triggered by a 36- minus-1 tooth trigger pulse wheel located on
the crankshaft (6303) inside the engine front cover (6019).
The sine wave type signal generated from the crankshaft position sensor provides two types of
information:
zposition of the crankshaft in 10 degree increments
z the crankshaft speed (rpm)
The powertrain control module (PCM) (12A650) uses this information to determine ignition coil turn ON
and turn OFF times and misfire detection.
For additional information, refer to Section 303 - 14 .
SECTION 303-
07B: Engine Ignition — 4.6L (2V) 2003 Mustang Workshop Manual Klj . 1 ba
22003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

DESCRIPTION AND OPERATION
Engine Ignition
Eight separate ignition coils:
zare controlled by the powertrain control module (PCM).
z are mounted directly above each spark plug.
z are controlled by the powertrain control module for correct firing sequence.
The spark plug:
zchanges the high voltage pulse into a spark which ignites the fuel and air mixture.
z originally equipped on the vehicle has a platinum- enhanced active electrode for long life.
The crankshaft position (CKP) sensor:
NOTE: Initial engine ignition timing is set at 10 degrees ± 2 degrees before top dead center (BTDC)
and is not adjustable. For additional information, refer to the Powertrain Control/Emissions Diagnosis
(PC/ED) manual.
zis a variable reluctance sensor, triggered by a 36- minus-1 tooth trigger pulse wheel located on
the crankshaft, inside the engine front cover.
The sine wave type signal generated from the crankshaft position sensor provides two types of
information:
zposition of the crankshaft in 10 degree increments
z the crankshaft speed (rpm)
For additional information, refer to Section 303 - 14 .
SECTION 303-
07C: Engine Ignition — 4.6L (4V) 2003 Mustang Workshop Manual Klj . 1 ba
22003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...