2003 FORD MUSTANG belt

DESCRIPTION AND OPERATION
Warning Devices
The warning device system consists of the following components:
zdoor ajar switches
z generic electronic module (GEM)
z key- in-ignition warning switch
z safety belt switch
z parklamp switch
SECTION 413-
09: Warning Devices 2003 Mustang Workshop Manual Klj . 1 ba
12003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

and when the GEM detects the headlamps or parklamps are on from the exterior lamp circuits. Refer
to the Chime Duration Table in this section for audible output, duration time, and priority ratings.
Safety Belt Warning Chime
The safety belt warning chime and safety belt warning lamp activate when the GEM detects the
ignition switch circuits are in the RUN or START state and when the GEM detects the safety belt is
unbuckled from the safety belt circuit. The safety belt warning lamp indicator will prove out for three
seconds whenever the GEM detects that the ignition circuits make a transition to RUN from OFF, ACC,
or KEYOUT state. Refer to the Chime Duration Table in this section for audible output, duration time,
and priority ratings.
Belt Minder
NOTE:
Belt minder is a configurable item. If configuring using a diagnostic tool, refer to Section 418 -
01 . To configure without using a diagnostic tool, refer to
Belt Minder Deactivating/Activating in this
section.
The belt minder feature supplements the current safety belt warning function. The belt minder feature
is enabled after the current safety belt warning is complete. If the driver safety belt is not buckled
approximately five seconds after the safety belt warning light has turned off, the belt minder reminds
the driver that their safety belt is unbuckled by intermittently sound a chime and illuminating the safety
belt warning lamp in the instrument cluster. While activated, the belt minder alternates the chime and
indicator from on for six seconds to off for 30 seconds.
The belt minder reminder stops when:
zthe drive seat belt is buckled.
z the ignition is turned to OFF or ACC.
z five minutes have elapsed since belt minder has started.
Inspection and Verification
NOTE: Upon installation of a new GEM, the module must be reconfigured. For additional information,
refer to Section 418 - 01 .
1. The warning lamps are a GEM controlled system; refer to Section 419 - 10 .
2. Verify the customer concern by operating the system in question.
3. Visually inspect for the following obvious signs of mechanical and electrical damage.
Chime Duration Table Feature Audible Output Duration Priority
Safety belt Chime, 60/minute 740 Hz 6.0 seconds 1
Key-
in-ignition Chime, 120/minute 740 Hz Continuous 2
Headlamps left on Chime, 240/minute 740 Hz Continuous 3
Airbag Single tone, 1,000 Hz Continuous 4
Door ajar Single tone, 1,000 Hz 1.0 second 7 Klj . 2 ba
202003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

4. If the concern remains after the inspection, connect the diagnostic tool to the data link connector
(DLC) located beneath the instrument panel and select the vehicle to be tested from the
diagnostic tool menu. If the diagnostic tool does not communicate with the vehicle:
zcheck that the program card is correctly installed.
z check the connections to the vehicle.
z check the ignition switch position.
5. If the diagnostic tool still does not communicate with the vehicle, refer to the diagnostic tool manual.
6. Carry out the Data Link Diagnostic Test. If the diagnostic tool responds with: zCKT914, CKT915 or CKT70 = ALL ECUS NO RESP/NOT EQUIP, refer to Section 418 -
00 .
z NO RESP/NOT EQUIP for GEM, go to Pinpoint Test A.
z NO RESP/NOT EQUIP for RCM, refer to Section 501 - 20B .
z SYSTEM PASSED, retrieve and record the continuous diagnostic trouble codes (DTCs),
erase the continuous DTCs and carry out self- test diagnostics for the GEM.
7. If the DTCs retrieved are related to the concern, go to the GEM Diagnostic Trouble Code (DTC) Index to continue diagnostics.
8. If no DTCs related to the concern are retrieved, proceed to the Symptom Chart to continue diagnostics.
9. If the DTCs retrieved are for the RCM, refer to Section 501 - 20B .
Visual Inspection Chart Mechanical Electrical
z
Switch(es) z
Central junction box (CJB) fuses:
„28 (15A)
„ 32 (15A)
„ 39 (5A)
z Circuitry
GEM Diagnostic Trouble Code (DTC) Index DTC Description Source Action
B1340 Chime Input Request
Circuit Short to Ground GEM Go To Pinpoint Test C .
B1342 ECU Is Defective GEM CLEAR the DTCs. TEST the system for normal operation.
RETRIEVE the DTCs. If DTC B1342 is retrieved, INSTALL
a new GEM. REFER to
Section 419 - 10 .
B1353 Ignition Key-
In Circuit
Open GEM Go To Pinpoint Test B .
B1462 Safety Belt Switch
Circuit Failure GEM Go To Pinpoint Test F . Klj . 3 ba
202003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

Symptom Chart
Symptom Chart Condition
Possible Sources Action
z No communication with the
generic electronic module
(GEM) z
Central junction box
(CJB) fuses:
„39 (5A).
„ 32 (15A).
z Circuitry.
z Generic electronic
module (GEM). z
Go To Pinpoint Test
A .
z The key- in-ignition chime does
not operate correctly z
Central junction box
(CJB) fuses:
„28 (15A).
„ 32 (15A).
z Central junction box
(CJB).
z Driver door ajar
switch.
z Key- in ignition
switch.
z Circuitry.
z Generic electronic
module (GEM).
z Ignition switch. z
Go To Pinpoint Test
B .
z A chime does not operate
correctly— air bag z
Restraint control
module (RCM).
z Circuitry.
z Generic electronic
module (GEM).
z Ignition switch. z
Go To Pinpoint Test
C .
z The door ajar chime does not
operate correctly z
Driver door ajar
switch.
z Passenger door ajar
switch.
z Circuitry.
z Generic electronic
module (GEM).
z Ignition switch. z
Go To Pinpoint Test
D .
z The headlamp on reminder
chime does not operate
correctly z
Headlamp switch .
z Circuitry.
z Generic electronic
module (GEM).
z Driver door ajar
switch.
z Ignition switch. z
Go To Pinpoint Test
E .
z The safety belt warning chime
does not operate correctly z
Circuitry.
z Safety belt switch.
z Generic electronic
module (GEM).
z Ignition switch. z
Go To Pinpoint Test
F .
z The belt minder feature does
not operate correctly z
Circuitry.
z Safety belt switch.
z Generic electronic
module (GEM).
z Ignition switch. z
Go To Pinpoint Test
F . Klj . 4 ba
202003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

PINPOINT TEST F: THE SAFETY BELT WARNING CHIME DOES NOT
OPERATE CORRECTLY z
Is the resistance less than 5 ohms? E8 TEST CIRCUIT 14 (BN) FOR SHORT TO BATTERY
z
Key in OFF position.
z Disconnect: GEM C201c.
z Set the headlamp switch in the OFF position. Measure the
voltage between GEM C201c pin 7, circuit 14 (BN),
harness side and ground.
z Is the voltage greater than 10 volts? Yes
REPAIR the circuit. REPEAT
the self-
test. CLEAR the
DTCs.
No
GO to E9 .
E9 CHECK FOR CORRECT MODULE OPERATION
z
Check:
zfor corrosion
z for pushed- out pins
z connector seated correctly
z Connect any disconnected connectors.
z Make sure all other system connectors are fully seated.
z Operate the system and verify the concern is still present.
z Is the concern still present? Yes
INSTALL a new GEM.
REFER to
Section 419 - 10 .
CLEAR the DTCs. REPEAT
the GEM self- test.
No
The system is operating
correctly at this time.
Concern may have been
caused by a loose or
corroded connector. CLEAR
the DTCs. REPEAT the self-
test. Test Step Result / Action to Take
F1 CHECK IGNITION STATES
NOTE:
Verify the belt minder is activated before
diagnosing.
z Connect the diagnostic tool.
z Enter the following diagnostic mode on the diagnostic tool:
GEM PID. Yes
GO to
F2 .
No
Go To Pinpoint Test B . Klj . 17 ba
202003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

z
Monitor the GEM PIDS IGN_KEY, IGN_A, IGN_S, and
IGN_R while cycling the ignition switch through the OFF,
ACC, RUN, START and key out positions.
z Do the PID values agree with the ignition switch
states? F2 DETERMINE IF THE GEM IS RECEIVING CORRECT
SAFETY BELT SWITCH STATUS z
Key in ON position.
z Enter the following diagnostic mode on the diagnostic tool:
GEM PID.
z Monitor the GEM PID D_SBELT while buckling and
unbuckling the driver safety belt.
z Does the GEM PID D_SBELT read OUT and IN
correctly? Yes
GO to
F3 .
No
GO to F5 .
F3 CHECK THE GEM INTERNAL TONE OPERATION
z
Enter the following diagnostic mode on the diagnostic tool:
GEM Active Command.
z Trigger the GEM active command CHIME ON and OFF.
z Does the chime operate correctly? Yes
GO to
F4 .
No
GO to F11 .
F4 CHECK THE SAFETY BELT WARNING LAMP OPERATION
z
Cycle the ignition switch from OFF to RUN while monitoring
the instrument cluster safety belt indicator lamp.
z Does instrument cluster safety belt indicator lamp
illuminate for approximately three seconds? Yes
GO to
F11 .
No
REFER to Section 413 - 01 .
F5 DETERMINE IF CIRCUIT 85 (BN/LB) IS OPEN OR
SHORTED TO GROUND z
Enter the following diagnostic mode on the diagnostic tool:
GEM PID.
z Monitor the GEM PID D_SBELT, while buckling and
unbuckling the driver safety belt.
z Does the GEM PID D_SBELT value indicate OUT with
the driver safety belt buckled? Yes
GO to
F6 .
No
GO to F8 .
F6 ISOLATE THE SHORT TO GROUND ON CIRCUIT 85
(BN/LB) z
Disconnect: Safety Belt Switch C323.
z Enter the following diagnostic mode on the diagnostic tool:
GEM PID.
z Monitor the GEM PID D_SBELT.
z Does the GEM PID D_SBELT value indicate IN? Yes
INSTALL a new safety belt
switch. REPEAT the self-
test. CLEAR the DTCs.
No
GO to
F7 .
F7 CHECK CIRCUIT 85 (BN/LB) FOR A SHORT TO GROUND
BETWEEN GEM AND SAFETY BELT SWITCH z
Disconnect: GEM C201d.
z Measure the resistance between GEM C201d pin 8, circuit
85 (BN/LB), harness side and ground. Yes
GO to
F11 .
No
REPAIR the circuit. REPEAT
the self- test. CLEAR the
DTCs. Klj . 18 ba
202003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

z
Is the resistance greater than 10,000 ohms? F8 ISOLATE OPEN ON CIRCUIT 85 (BN/LB)
z
Disconnect: Safety Belt Switch C323.
z Enter the following diagnostic mode on the diagnostic tool:
GEM PID.
z Connect a 10A fused jumper wire between safety belt
switch C323 pin 2, circuit 85 (BN/LB), harness side and
ground while monitoring GEM PID D_SBELT.
z Does GEM PID GEM PID D_SBELT read OUT with
jumper wire installed? Yes
GO to
F10 .
No
GO to F9 .
F9 CHECK CIRCUIT 85 (BN/LB) FOR OPEN BETWEEN GEM
AND SEATBELT SWITCH z
Disconnect: Safety Belt Switch C323.
z Disconnect: GEM C201b.
z Measure the resistance between GEM C201b pin 8, circuit
85 (BN/LB), harness side and safety belt switch C323 pin 2,
circuit 85 (BN/LB), harness side.
z Is the resistance less than 5 ohms? Yes
GO to
F11 .
No
REPAIR the circuit. CLEAR
the DTCs. TEST the system
for normal operation. F10 CHECK CIRCUIT 1205 (BK) FOR AN OPEN CIRCUIT
BETWEEN SAFETY BELT SWITCH AND GROUND z
Disconnect: Safety Belt Switch C323.
z Measure the resistance between the safety belt switch
C323 pin 1, circuit 1205 (BK), harness side and ground. Yes
INSTALL a new safety belt
switch. REPEAT the self-
test. CLEAR the DTCs. Klj . 19 ba
202003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...

GENERAL PROCEDURES
Belt Minder Deactivating/Activating
Preparation
1. Before deactivating/activating the belt minder, set the parking brake.
2. Place the gearshift in P (Park) (automatic transmission) or the neutral position (manual transmission).
3. Place the ignition switch in the OFF position.
4. Close all the vehicle doors.
5. Unbuckle the driver safety belt.
6. Place the parklamps/headlamps switch in the OFF position. (If the vehicle is equipped with Autolamps, this will not affect the procedure.)
Deactivating/Activating 1. Turn the ignition switch to the RUN position. (Do not start the engine.)
2. Wait until the safety belt warning lamp turns off. (approximately one to two minutes)
3. NOTE: Steps 3 through 5 must be completed within 60 seconds or the procedure must be
repeated.
Buckle then unbuckle the safety belt three times, ending with the safety belt unbuckled. This
portion of the procedure can be done before or during belt minder warning activation.
4. Turn the parklamps/headlamps on then off.
5. Buckle then unbuckle the safety belt three times ending with the safety belt unbuckled. After this step the safety belt warning lamp will be illuminated for three seconds.
6. Within seven seconds of the safety belt warning lamp turning off, buckle then unbuckle the safety belt. This will enable the belt minder if disabled or disable the belt minder if enabled.
7. The following sequence of events confirm the belt minder is enabled: zflashing of the safety belt warning belt lamp four times per second for three seconds
z three seconds with the safety belt lamp off
z flashing the safety belt lamp four times per second for three seconds again
8. The safety belt lamp flashing four times per second for three seconds provides confirmation that the belt minder is disabled. 9. After confirmation, the deactivation/activation procedure is complete. SECTION 413-
09: Warning Devices 2003 Mustang Workshop Manual Klj . 1 ba
22003 Mustang Workshop Manual
18. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_5108/S3B~us~en~ ...