2003 FORD MUSTANG fuel

10.
NOTE: Lubricate O- ring with clean PAG oil or equivalent.
Connect the A/C suction tube to the accumulator.
11. Connect the heater hose.
12. Install the throttle body. For additional information, refer to Section 303 - 04D .
13. Connect the fuel tube spring lock coupling. For additional information, refer to Section 310 - 00 .
14. Install the RH ignition coils.
15. Connect the RH ignition coil electrical connectors. Klj . 8 ba
92003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

9. Disconnect the electrical connector.
10. Drain the engine cooling system. For additional information, refer to Section 303 - 03A .
11. Disconnect the fuel tube spring lock coupling. For additional information, refer to Section 310 -
00 .
12. Remove the upper radiator hose (8260).
13. Disconnect the throttle cable, and the speed control cable, and remove the throttle return spring. Klj . 3 ba
192003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

13. Disconnect the fuel pressure damper electrical connector.
14. Disconnect the EGR vacuum regulator electrical connector.
15. Disconnect the four LH fuel injector electrical connectors.
16. Remove the LH coil cover. Klj . 5 ba
212003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

24. Disconnect the four RH fuel injector electrical connectors.
25. Disconnect the engine coolant temperature (ECT) sensor.
26. Disconnect the RH ignition coils.
27. Remove the eight ignition coils. Klj . 8 ba
212003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

40. Remove the bolts and the RH valve cover.
41. Remove the knock sensor wiring harness.
1. LH knock sensor electrical connector.
2. RH knock sensor electrical connector.
3. Engine control sensor electrical connector.
4. Fuel injector electrical connector.
5. A/C compressor electrical connector.
6. Crankshaft position sensor (CKP) electrical connector.
42. Remove the knock sensors. Klj . 12 ba
212003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

59. Install the knock sensor wiring harness.
1. LH knock sensor electrical connector
2. RH knock sensor electrical connector
3. Engine control sensor electrical connector
4. Fuel injector electrical connector
5. A/C compressor electrical connector
6. CKP sensor electrical connector
60. Install the lower intake manifold. zPosition the gaskets.
z Install the intake manifold and tighten the bolts in the sequence shown.
61. Install the generator. Klj . 21 ba
302003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

65. Connect the engine coolant temperature (ECT) sensor.
66. Connect the eight fuel injectors.
67. Install the RH ignition coil cover.
68.
NOTE: The fastener at location five is a stud. Install the gasket and the upper intake. Klj . 23 ba
302003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

72. Install the LH coil cover.
73. Connect the EGR vacuum regulator (EVR) electrical connector.
74. Connect the fuel pressure sensor electrical connector.
75. Connect the EGR tube to the exhaust manifold. Klj . 25 ba
302003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...