2003 FORD MUSTANG fuel

29. Remove the harness support bracket.
30. Disconnect the electrical connectors and remove the RH ignition coils.
31. Disconnect the eight fuel injectors.
32. Separate the harness from the fuel supply manifold studs in four places and remove the fuel
charging wiring harness. Klj . 9 ba
232003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

33.
NOTE: The intake manifold gaskets are reusable if undamaged.
Remove the ten bolts and the intake manifold, and the supercharger and fuel supply manifold
as an assembly.
34. Remove the bolts and the heater water outlet tube.
35. Remove the bolts and the heater water inlet tube.
36. NOTE: LH is shown, RH is similar. Klj . 10 ba
232003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

68.
NOTE: Lubricate the O- ring with clean engine coolant.
Install the heater water inlet tube.
69. NOTE: Lubricate the O- rings with clean engine coolant.
Install the heater water outlet tube and the mounting bolts.
70. NOTE: Inspect the intake manifold gaskets and install new gaskets, if necessary.
Install the intake manifold, supercharger and fuel supply manifold as an assembly, and tighten
the bolts to 10 Nm (89 lb- in) in the sequence shown. Klj . 25 ba
352003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

71. Position the wiring harness onto the engine and attach it to the four fuel supply manifold studs.
72. Connect the eight fuel injector electrical connectors.
73.
NOTE: RH is shown, LH is similar.
Install the RH and LH ignition coils and connect the electrical connectors.
74. Install the harness support bracket. Klj . 26 ba
352003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

75. Clip the harness to the bracket.
76. Connect the A/C compressor electrical connector.
77. Connect the crankshaft position (CKP) sensor electrical connector.
78. Install the fuel charging wiring harness bracket bolt. Klj . 27 ba
352003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

91. Install the vacuum accessory bracket mounting nut.
92. Position the vacuum harness and connect the vacuum hoses to the back of the supercharger.
93. Connect the vacuum hose to the EGR valve.
94. Connect the vacuum hoses to the fuel pulse damper and the EGR vacuum regulator solenoid. Klj . 31 ba
352003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

95. Connect the vacuum hoses to the supercharger bypass vacuum solenoid and the actuator.
96. Connect the vacuum hoses to the differential pressure feedback EGR system.
97. Connect the electrical connectors to the fuel pulse damper, EGR vacuum regulator solenoid,
supercharger bypass vacuum solenoid, and the differential pressure feedback EGR system. 98. Install the drain plug. Klj . 32 ba
352003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...

51. Connect the accelerator controls.
zConnect the accelerator cable.
z If equipped, connect the speed control cable.
52. Connect the fuel tube spring lock coupling. For additional information, refer to Section 310 - 00 .
53. Connect the A/C pressure switch electrical connector.
54. Connect the vacuum hose. Klj . 14 ba
172003 Mustang Workshop Manual
17. 11. 2011file:///C:/Ford/2000 - 2004/tsocache/SHEF_4464/S3B~us~en~ ...