2003 DODGE RAM Radio

INSTALLATION
(1) Position the oil pump onto the crankshaft and
install one oil pump retaining bolts.
(2) Position the primary timing chain tensioner
and install three retaining bolts.
(3) Tighten the oil pump and primary timing chain
tensioner retaining bolts to 28 N´m (250 in. lbs.) in
the sequence shown (Fig. 107).
(4) Install the secondary timing chain tensioners
and timing chains (Refer to 9 - ENGINE/VALVE
TIMING/TIMING BELT/CHAIN AND SPROCKETS -
INSTALLATION).
(5) Install the timing chain cover (Refer to 9 -
ENGINE/VALVE TIMING/TIMING BELT / CHAIN
COVER(S) - INSTALLATION).
(6) Install the pick-up tube and oil pan (Refer to 9
- ENGINE/LUBRICATION/OIL PAN - INSTALLA-
TION).
INTAKE MANIFOLD
DESCRIPTION
The intake manifold is made of a composite mate-
rial and features long runners which maximizes low
end torque. The intake manifold uses single plane
sealing which consist of eight individual press in
place port gaskets to prevent leaks. Eight studs and
two bolts are used to fasten the intake to the head.
DIAGNOSIS AND TESTINGÐINTAKE
MANIFOLD LEAKAGE
An intake manifold air leak is characterized by
lower than normal manifold vacuum. Also, one or
more cylinders may not be functioning.
WARNING: USE EXTREME CAUTION WHEN THE
ENGINE IS OPERATING. DO NOT STAND IN A
DIRECT LINE WITH THE FAN. DO NOT PUT YOUR
HANDS NEAR THE PULLEYS, BELTS OR THE FAN.
DO NOT WEAR LOOSE CLOTHING.
(1) Start the engine.
(2) Spray a small stream of water at the suspected
leak area.
(3) If a change in RPM is observed the area of the
suspected leak has been found.
(4) Repair as required.
REMOVAL
(1) Disconnect negative cable from battery.
(2) Remove resonator assembly and air inlet hose.
(3) Disconnect throttle and speed control cables.
(4) Disconnect electrical connectors for the follow-
ing components:
²Manifold Absolute Pressure (MAP) Sensor
²Intake Air Temperature (IAT) Sensor
²Throttle Position (TPS) Sensor
²Coolant Temperature (CTS) Sensor
²Idle Air Control (IAC) Motor
(5) Disconnect brake booster hose and positive
crankcase ventilation (PCV) hose.
(6) Disconnect generator electrical connections.
(7) Disconnect air conditioning compressor electri-
cal connections.
(8) Disconnect left and right radio suppressor
straps.
(9) Disconnect and remove ignition coil towers
(Refer to 8 - ELECTRICAL/IGNITION CONTROL/
IGNITION COIL - REMOVAL).
(10) Remove top oil dipstick tube retaining bolt
and ground strap.
(11) Bleed fuel system (Refer to 14 - FUEL SYS-
TEM/FUEL DELIVERY - STANDARD PROCE-
DURE).
(12) Remove fuel rail (Refer to 14 - FUEL SYS-
TEM/FUEL DELIVERY/FUEL RAIL - REMOVAL).
(13) Remove throttle body assembly and mounting
bracket.
(14) Drain cooling system below coolant tempera-
ture level (Refer to 7 - COOLING - STANDARD
PROCEDURE).
(15) Remove the heater hoses from the engine
front cover and the heater core.
Fig. 107 Oil Pump And Primary Timing Chain
Tensioner Tightening Sequence
DRENGINE - 4.7L 9 - 157
OIL PUMP (Continued)

(16) Unclip and remove heater hoses and tubes
from intake manifold (Fig. 108).
(17) Remove coolant temperature sensor (Refer to
7 - COOLING/ENGINE/ENGINE COOLANT TEM-
PERATURE SENSO - REMOVAL).
(18) Remove intake manifold retaining fasteners in
reverse order of tightening sequence (Fig. 109).
(19) Remove intake manifold.CLEANING
NOTE: There is NO approved repair procedure for the
intake manifold. If severe damage is found during
inspection, the intake manifold must be replaced.
Before installing the intake manifold thoroughly
clean the mating surfaces. Use a suitable cleaning
solvent, then air dry.
INSPECTION
(1) Inspect the intake sealing surface for cracks,
nicks and distortion.
(2) Inspect the intake manifold vacuum hose fit-
tings for looseness or blockage.
(3) Inspect the manifold to throttle body mating
surface for cracks, nicks and distortion.
INSTALLATION
(1) Install intake manifold gaskets.
(2) Position intake manifold.
(3) Install intake manifold retaining bolts and
tighten in sequence shown in (Fig. 109) to 12 N´m
(105 in. lbs.).
(4) Install left and right radio suppressor straps.
(5) Install throttle body assembly.
(6) Install throttle cable bracket.
(7) Connect throttle cable and speed control cable
to throttle body.
(8) Install fuel rail (Refer to 14 - FUEL SYSTEM/
FUEL DELIVERY/FUEL RAIL - INSTALLATION).
(9) Install ignition coil towers (Refer to 8 - ELEC-
TRICAL/IGNITION CONTROL/IGNITION COIL -
INSTALLATION).
(10) Position and install heater hoses and tubes
onto intake manifold.
(11) Install the heater hoses to the heater core and
engine front cover.
(12) Connect electrical connectors for the following
components:
²Manifold Absolute Pressure (MAP) Sensor
²Intake Air Temperature (IAT) Sensor
²Throttle Position (TPS) Sensor
²Coolant Temperature (CTS) Sensor
²Idle Air Control (IAC) Motor
²Ignition coil towers
²Fuel injectors
(13) Install top oil dipstick tube retaining bolt and
ground strap.
(14) Connect generator electrical connections.
(15) Connect Brake booster hose and Positive
crankcase ventilation (PCV) hose.
(16) Fill cooling system (Refer to 7 - COOLING -
STANDARD PROCEDURE).
(17) Install resonator assembly and air inlet hose.
(18) Connect negative cable to battery.
Fig. 108 Heater Hoses and Tubes Removal /
Installation
1 - HEATER HOSES AND TUBES
2 - ROUTING/RETAINING CLIPS
Fig. 109 Intake Manifold Tightening Sequence
9 - 158 ENGINE - 4.7LDR
INTAKE MANIFOLD (Continued)

(16) Disconnect the air bag control module electri-
cal connector.
(17) Remove the right cowl trim cover. (Refer to 23
- BODY/INTERIOR/COWL TRIM - REMOVAL)
(18) Disconnect the two electrical connectors. (Fig.
11 )
(19) Disconnect the radio antenna. (Fig. 12)
(20) Remove the one HVAC screw. (Fig. 13)(21) Using a trim stick C-4755 or equivalent, from
the notch on the bottom, remove the right end cap.
(Fig. 14)
(22) Remove the right a-pillar trim. (Refer to 23 -
BODY/INTERIOR/A-PILLAR TRIM/GRAB HANDLE
- REMOVAL)
(23) Remove the two right side mounting bolts on
the a-pillar and one right mounting bolt on the cowl
side panel. (Fig. 14)
Fig. 10 CENTER MOUNTING BOLTS
1 - INSTRUMENT PANEL
2 - BOLTS
Fig. 11 RIGHT WIRE HARNESS CONNECTIONS
1 - COWL SIDE PANEL
2 - ELECTRICAL CONNECTORS
Fig. 12 ANTENNA CONNECTION
1 - ANTENNA CABLE
2 - RADIO CABLE
Fig. 13 HVAC/INSTRUMENT PANEL MOUNTING
1-HVAC
2 - MOUNTING SCREW
3 - LOWER SURROUND SCREWS
4 - GLOVE BOX OPENING
DRINSTRUMENT PANEL 23 - 55
INSTRUMENT PANEL ASSEMBLY (Continued)

(11) Install the right a-pillar trim panel. (Refer to
23 - BODY/INTERIOR/A-PILLAR TRIM - INSTAL-
LATION)
(12) Position the right end cap and seat the
attachment clips fully.
(13) Install the one HVAC mounting screw.
(14) Connect the radio antenna.
(15) Connect the two electrical connectors at the
right cowl panel.
(16) Install the right cowl trim cover. (Refer to 23 -
BODY/INTERIOR/COWL TRIM - INSTALLATION)
(17) Connect the air bag control module electrical
connector.
(18) Install the center bracket bolts and tighten to
12 N´m (9 ft. lbs.).
(19) Install the floor console, if equipped. (Refer to
23 - BODY/INTERIOR/FLOOR CONSOLE - INSTAL-
LATION)
(20) Install the air bag control module cover, if
equipped.
(21) Connect the park brake release handle actua-
tor rod.
(22) Install the hood release handle and tighten
the screws.
(23) Install the two bolts at the column support
bracket and tighten to 14 N´m (10 ft. lbs.).
(24) Install the steering column. (Refer to 19 -
STEERING/COLUMN - INSTALLATION)
(25) Connect the wire harness electrical connectors
above the brake pedal.
(26) Install the two top instrument panel bolts and
tighten to 12 N´m (9 ft. lbs.).
(27) Install the four top instrument panel screws.
(28) Install the instrument panel top cover. (Refer
to 23 - BODY/INSTRUMENT PANEL/INSTRUMENT
PANEL TOP COVER - INSTALLATION)
INSTRUMENT PANEL
HEADLAMP SWITCH BEZEL
REMOVAL
WARNING: ON VEHICLES EQUIPPED WITH AIR-
BAGS, DISABLE THE AIRBAG SYSTEM BEFORE
ATTEMPTING ANY STEERING WHEEL, STEERING
COLUMN, SEAT BELT TENSIONER, OR INSTRU-
MENT PANEL COMPONENT DIAGNOSIS OR SER-
VICE. DISCONNECT AND ISOLATE THE BATTERY
NEGATIVE (GROUND) CABLE, THEN WAIT TWO
MINUTES FOR THE AIRBAG SYSTEM CAPACITOR
TO DISCHARGE BEFORE PERFORMING FURTHER
DIAGNOSIS OR SERVICE. THIS IS THE ONLY SURE
WAY TO DISABLE THE AIRBAG SYSTEM. FAILURE
TO TAKE THE PROPER PRECAUTIONS COULDRESULT IN ACCIDENTAL AIRBAG DEPLOYMENT
AND POSSIBLE PERSONAL INJURY.
(1) Using a trim stick C-4755 or equivalent,
release the top clips on the steering column opening
cover and the lower drivers side bezel.
(2) Using a trim stick C-4755 or equivalent,
release the switch bezel. (Fig. 17)
(3) Disconnect the electrical connector and remove
the bezel.
INSTALLATION
WARNING: ON VEHICLES EQUIPPED WITH AIR-
BAGS, DISABLE THE AIRBAG SYSTEM BEFORE
ATTEMPTING ANY STEERING WHEEL, STEERING
COLUMN, SEAT BELT TENSIONER, OR INSTRU-
MENT PANEL COMPONENT DIAGNOSIS OR SER-
VICE. DISCONNECT AND ISOLATE THE BATTERY
NEGATIVE (GROUND) CABLE, THEN WAIT TWO
MINUTES FOR THE AIRBAG SYSTEM CAPACITOR
TO DISCHARGE BEFORE PERFORMING FURTHER
DIAGNOSIS OR SERVICE. THIS IS THE ONLY SURE
WAY TO DISABLE THE AIRBAG SYSTEM. FAILURE
TO TAKE THE PROPER PRECAUTIONS COULD
RESULT IN ACCIDENTAL AIRBAG DEPLOYMENT
AND POSSIBLE PERSONAL INJURY.
(1) Connect the electrical connector.
(2) Position the switch bezel and seat the attach-
ment clips fully.
(3) Seat the clips on the steering column opening
cover and the lower drivers side bezel fully.
Fig. 17 HEADLIGHT SWITCH BEZEL
1 - SWITCH BEZEL
2 - INSTRUMENT PANEL
3 - ELECTRICAL CONNECTOR
4 - HEADLIGHT SWITCH
DRINSTRUMENT PANEL 23 - 57
INSTRUMENT PANEL ASSEMBLY (Continued)

DISTRIBUTION
TABLE OF CONTENTS
page page
AIR OUTLETS
REMOVAL - PANEL OUTLETS.............24
INSTALLATION - PANEL OUTLETS..........24
BLEND DOOR
REMOVAL.............................24
INSTALLATION.........................25
BLOWER MOTOR
DESCRIPTION.........................25
OPERATION...........................25
DIAGNOSIS AND TESTING - BLOWER
MOTOR .............................26
REMOVAL.............................26
INSTALLATION.........................26
DEFROST DOOR
REMOVAL - DEFROST DOOR.............27
INSTALLATION - DEFROST DOOR..........27
FLOOR DISTRIBUTION DUCTS
REMOVAL.............................27INSTALLATION.........................27
HVAC HOUSING
REMOVAL.............................27
DISASSEMBLY.........................28
ASSEMBLY............................28
INSTALLATION.........................29
INSTRUMENT PANEL DUCTS
REMOVAL.............................29
INSTALLATION.........................29
MODE DOOR
REMOVAL - FLOOR - DEFROST DOOR......30
INSTALLATION - FLOOR - DEFROST DOOR . . 30
RECIRC DOOR
REMOVAL.............................30
INSTALLATION.........................30
AIR OUTLETS
REMOVAL - PANEL OUTLETS
(1) Use a trim stick or another suitable wide flat-
bladed tool to gently pry the panel outlet grill out of
the panel outlet housing (Fig. 1). The panel outlet
grill is retained by a light snap fit.
INSTALLATION - PANEL OUTLETS
To install, position the grill housing in the panel
outlet housing and press firmly until it snaps into
place.
BLEND DOOR
REMOVAL
WARNING: ON VEHICLES EQUIPPED WITH AIR-
BAGS, DISABLE THE AIRBAG SYSTEM BEFORE
ATTEMPTING ANY STEERING WHEEL, STEERING
COLUMN, OR INSTRUMENT PANEL COMPONENT
DIAGNOSIS OR SERVICE. DISCONNECT AND ISO-
LATE THE BATTERY NEGATIVE (GROUND) CABLE,
THEN WAIT TWO MINUTES FOR THE AIRBAG SYS-
TEM CAPACITOR TO DISCHARGE BEFORE PER-
FORMING FURTHER DIAGNOSIS OR SERVICE. THIS
IS THE ONLY SURE WAY TO DISABLE THE AIRBAG
SYSTEM. FAILURE TO TAKE THE PROPER PRE-CAUTIONS COULD RESULT IN AN ACCIDENTAL
AIRBAG DEPLOYMENT AND POSSIBLE PERSONAL
INJURY.
Fig. 1 Dash Panel
1 - Headlight Switch
2 - Air Outlets
3 - Instrument Cluster
4 - Climate Control
5 - Radio
6 - Airbag
7 - Glove Box
8 - Heated Seat Switch (if equipped)
9 - Transfer Case Control Switch (if equipped)
10 - Cigar Lighter
11 - Cup Holders
12 - Ash Tray (if equipped)
13 - Power Outlet
24 - 24 DISTRIBUTIONDR

GOVERNOR - REMOVAL, ELECTRONIC . . 21-198,
21-378
GRAB HANDLE - INSTALLATION,
B-PILLAR...........................23-69
GRAB HANDLE - REMOVAL, B-PILLAR....23-69
GRILLE - INSTALLATION...............23-40
GRILLE - INSTALLATION, COWL.........23-38
GRILLE - REMOVAL..................23-39
GRILLE - REMOVAL, COWL............23-38
GRILLE FRAME - INSTALLATION.........23-40
GRILLE FRAME - REMOVAL............23-40
GROUND - STANDARD PROCEDURE,
TESTING FOR A SHORT TO..........8W-01-9
GROUND AND SPLICE INFORMATION -
DESCRIPTION, CONNECTOR..........8W-01-7
GROUND ON FUSES POWERING
SEVERAL LOADS - STANDARD
PROCEDURE, TESTING FOR A SHORT
TO.............................8W-01-10
GROUND STRAP - DESCRIPTION, RADIO
NOISE SUPPRESSION..................8A-8
GROUND STRAP - INSTALLATION,
RADIO NOISE SUPPRESSION...........8A-10
GROUND STRAP - OPERATION, RADIO
NOISE SUPPRESSION..................8A-8
GROUND STRAP - REMOVAL, RADIO
NOISE SUPPRESSION..................8A-9
GROUNDS - DESCRIPTION, POWER......8E-10
GUIDE SEALS - DESCRIPTION, VALVE . 9-31,9-36
GUIDES - DESCRIPTION, VALVE....9-106,9-197
GUIDES AND SPRINGS - STANDARD
PROCEDURE, VALVES............9-246,9-305
HALF SHAFT - CAUTION................3-11
HALF SHAFT - DIAGNOSIS AND TESTING . . 3-11
HALF SHAFT - INSTALLATION............3-12
HALF SHAFT - REMOVAL...............3-11
HALF SHAFT - SPECIAL TOOLS..........3-12
HALF SHAFT - SPECIFICATIONS..........3-12
HANDLE - INSTALLATION, A-PILLAR
TRIM/GRAB.........................23-64
HANDLE - INSTALLATION, B-PILLAR
GRAB..............................23-69
HANDLE - INSTALLATION, EXTERIOR....23-20,
23-30
HANDLE - INSTALLATION, RELEASE.......5-38
HANDLE - REMOVAL, A-PILLAR
TRIM/GRAB.........................23-64
HANDLE - REMOVAL, B-PILLAR GRAB....23-69
HANDLE - REMOVAL, EXTERIOR . . . 23-20,23-30
HANDLE - REMOVAL, RELEASE..........5-38
HANDLE ACTUATOR - INSTALLATION,
INSIDE........................23-22,23-32
HANDLE ACTUATOR - REMOVAL, INSIDE . 23-22,
23-31
HANDLE/LATCH REMOTE -
INSTALLATION, RELEASE..............23-17
HANDLE/LATCH REMOTE - REMOVAL,
RELEASE...........................23-17
HANDLING NON-DEPLOYED
SUPPLEMENTAL RESTRAINTS -
STANDARD PROCEDURE...............8O-6
HARNESS - DIAGNOSIS AND TESTING,
WIRING..........................8W-01-7
HAT BRAKE - CLEANING, REAR DRUM
IN .................................5-33
HAT BRAKE - INSPECTION, REAR DRUM
IN .................................5-33
HAZARD SWITCH - DESCRIPTION.......8L-13
HAZARD SWITCH - OPERATION.........8L-13
HCU (HYDRAULIC CONTROL UNIT) -
DESCRIPTION........................5-43
HCU (HYDRAULIC CONTROL UNIT) -
INSTALLATION........................5-44
HCU (HYDRAULIC CONTROL UNIT) -
OPERATION..........................5-43
HCU (HYDRAULIC CONTROL UNIT) -
REMOVAL...........................5-44
HD - INSTALLATION, 4X4..............19-15
HD - INSTALLATION, ALL LD & HD
EXCEPT 4X4........................19-15
HD - REMOVAL, 4X4
..................19-14
HD - REMOVAL, ALL LD & HD EXCEPT
4X4
...............................19-14
HD EXCEPT 4X4 HD - INSTALLATION,
ALL LD
............................19-15
HD EXCEPT 4X4 HD - REMOVAL, ALL LD
. 19-14
HEAD - CLEANING, CYLINDER
.....9-195,9-300,
9-372HEAD - DESCRIPTION, CYLINDER . . 9-106,9-243,
9-298,9-370
HEAD - INSPECTION, CYLINDER . . . 9-195,9-301,
9-372
HEAD - INSTALLATION, CYLINDER . . 9-195,9-372
HEAD - INSTALLATION, LEFT CYLINDER . . 9-110
HEAD - INSTALLATION, RIGHT
CYLINDER..........................9-111
HEAD - LEFT - INSTALLATION,
CYLINDER...........................9-23
HEAD - LEFT - REMOVAL, CYLINDER......9-21
HEAD - OPERATION, CYLINDER....9-194,9-243
HEAD - REMOVAL, CYLINDER.....9-195,9-298,
9-371
HEAD - REMOVAL, LEFT CYLINDER......9-106
HEAD - REMOVAL, RIGHT CYLINDER.....9-108
HEAD - RIGHT - INSTALLATION,
CYLINDER...........................9-32
HEAD - RIGHT - REMOVAL, CYLINDER....9-32
HEAD COVER - INSTALLATION,
CYLINDER..........................9-304
HEAD COVER - REMOVAL, CYLINDER....9-304
HEAD COVER GASKET - DESCRIPTION,
CYLINDER..........................9-243
HEAD COVER GASKET - OPERATION,
CYLINDER..........................9-243
HEAD COVER(S) - CLEANING, CYLINDER . 9-245,
9-374
HEAD COVER(S) - DESCRIPTION,
CYLINDER.................9-121,9-26,9-373
HEAD COVER(S) - INSPECTION,
CYLINDER.....................9-245,9-374
HEAD COVER(S) - INSTALLATION,
CYLINDER........9-196,9-245,9-27,9-36,9-374
HEAD COVER(S) - REMOVAL, CYLINDER . 9-196,
9-245,9-26,9-35,9-373
HEAD GASKET - DIAGNOSIS AND
TESTING, CYLINDER...................9-20
HEAD GASKET FAILURE - DIAGNOSIS
AND TESTING, CYLINDER....9-194,9-243,9-370
HEAD GASKET SELECTION - STANDARD
PROCEDURE........................9-330
HEADLAMP - INSTALLATION............8L-13
HEADLAMP - REMOVAL...............8L-13
HEADLAMP ALIGNMENT - SPECIAL
TOOLS..............................8L-7
HEADLAMP SWITCH - DESCRIPTION.....8L-14
HEADLAMP SWITCH - INSTALLATION....8L-14
HEADLAMP SWITCH - OPERATION.......8L-14
HEADLAMP SWITCH - REMOVAL........8L-14
HEADLAMP SWITCH BEZEL -
INSTALLATION, INSTRUMENT PANEL.....23-57
HEADLAMP SWITCH BEZEL - REMOVAL,
INSTRUMENT PANEL..................23-57
HEADLAMP UNIT - ADJUSTMENTS......8L-15
HEADLAMP UNIT - INSTALLATION.......8L-15
HEADLAMP UNIT - REMOVAL...........8L-15
HEADLINER - INSTALLATION...........23-69
HEADLINER - REMOVAL...............23-69
HEADREST - INSTALLATION............23-82
HEADREST - REMOVAL................23-82
HEADREST SLEEVE - INSTALLATION.....23-82
HEADREST SLEEVE - REMOVAL.........23-82
HEAT SHIELDS - DESCRIPTION..........11-7
HEAT SHIELDS - INSTALLATION..........11-8
HEAT SHIELDS - REMOVAL.............11-7
HEAT STAKING - STANDARD
PROCEDURE.........................23-3
HEATED MIRROR SYSTEM -
DESCRIPTION........................8G-1
HEATED MIRROR SYSTEM - DIAGNOSIS
AND TESTING........................8G-2
HEATED MIRROR SYSTEM - OPERATION . . . 8G-1
HEATED SEAT ELEMENT - DESCRIPTION . . . 8G-5
HEATED SEAT ELEMENT - DIAGNOSIS
AND TESTING........................8G-6
HEATED SEAT ELEMENT - INSTALLATION . . 8G-6
HEATED SEAT ELEMENT - OPERATION.....8G-6
HEATED SEAT ELEMENT - REMOVAL......8G-6
HEATED SEAT MODULE - DESCRIPTION....8E-6
HEATED SEAT MODULE - DIAGNOSIS
AND TESTING........................8E-7
HEATED SEAT MODULE - INSTALLATION
. . . 8E-7
HEATED SEAT MODULE - OPERATION
.....8E-6
HEATED SEAT MODULE - REMOVAL
.......8E-7
HEATED SEAT SENSOR - DESCRIPTION
....8G-7
HEATED SEAT SENSOR - DIAGNOSIS
AND TESTING
........................8G-7HEATED SEAT SENSOR - OPERATION.....8G-7
HEATED SEAT SENSOR - REMOVAL.......8G-7
HEATED SEAT SWITCH - DESCRIPTION....8G-7
HEATED SEAT SWITCH - DIAGNOSIS
AND TESTING........................8G-8
HEATED SEAT SWITCH - INSTALLATION . . . 8G-9
HEATED SEAT SWITCH - OPERATION......8G-8
HEATED SEAT SWITCH - REMOVAL.......8G-9
HEATED SEAT SYSTEM - DESCRIPTION....8G-3
HEATED SEAT SYSTEM - DIAGNOSIS
AND TESTING........................8G-4
HEATED SEAT SYSTEM - OPERATION.....8G-4
HEATER - 5.9L DIESEL - DESCRIPTION,
ENGINE BLOCK.......................7-43
HEATER - 5.9L DIESEL - INSTALLATION,
ENGINE BLOCK.......................7-44
HEATER - 5.9L DIESEL - OPERATION,
ENGINE BLOCK.......................7-43
HEATER - 5.9L DIESEL - REMOVAL,
ENGINE BLOCK.......................7-43
HEATER - DESCRIPTION, ENGINE BLOCK . . . 7-42
HEATER - DESCRIPTION, FUEL..........14-63
HEATER - DESCRIPTION, INTAKE AIR.....14-91
HEATER - DIAGNOSIS AND TESTING,
ENGINE BLOCK.......................7-42
HEATER - DIAGNOSIS AND TESTING,
FUEL..............................14-63
HEATER - INSTALLATION, ENGINE
BLOCK..............................7-43
HEATER - INSTALLATION, INTAKE AIR......14-91
HEATER - OPERATION, ENGINE BLOCK....7-42
HEATER - OPERATION, FUEL............14-63
HEATER - OPERATION, INTAKE AIR......14-91
HEATER - REMOVAL, ENGINE BLOCK......7-43
HEATER - REMOVAL, INTAKE AIR........14-91
HEATER AND AIR CONDITIONER -
DESCRIPTION........................24-1
HEATER AND AIR CONDITIONER -
OPERATION..........................24-1
HEATER CONTROL - DESCRIPTION, A/C . . . 24-14
HEATER CONTROL - INSTALLATION, A/C . . 24-15
HEATER CONTROL - REMOVAL, A/C......24-14
HEATER CORE - DESCRIPTION..........24-50
HEATER CORE - INSTALLATION.........24-50
HEATER CORE - OPERATION............24-50
HEATER CORE - REMOVAL.............24-50
HEATER PERFORMANCE - DIAGNOSIS
AND TESTING........................24-5
HEATER RELAY - DESCRIPTION, FUEL....14-64
HEATER RELAY - DESCRIPTION, INTAKE
AIR ...............................14-92
HEATER RELAY - INSTALLATION, FUEL . . . 14-64
HEATER RELAY - INSTALLATION, INTAKE
AIR ...............................14-93
HEATER RELAY - OPERATION, FUEL......14-64
HEATER RELAY - OPERATION, INTAKE
AIR ...............................14-92
HEATER RELAY - REMOVAL, FUEL.......14-64
HEATER RELAY - REMOVAL, INTAKE AIR . . 14-93
HEIGHT ADJUSTMENT - 4WD (LD) -
STANDARD PROCEDURE.................2-3
HEIGHT MEASUREMENT - 4WD (LD) -
STANDARD PROCEDURE.................2-3
HIGH BEAM INDICATOR - DESCRIPTION . . 8J-27
HIGH BEAM INDICATOR - OPERATION
....8J-28
HIGH MOUNTED STOP LAMP -
INSTALLATION, CENTER
...............8L-10
HIGH MOUNTED STOP LAMP -
REMOVAL, CENTER
...................8L-10
HIGH MOUNTED STOP LAMP UNIT -
INSTALLATION, CENTER
...............8L-10
HIGH MOUNTED STOP LAMP UNIT -
REMOVAL, CENTER
...................8L-10
HIGH PRESSURE RELIEF VALVE -
DESCRIPTION
.......................24-35
HIGH PRESSURE RELIEF VALVE -
OPERATION
.........................24-36
HIGH SPEEDS - DESCRIPTION, TIRE
PRESSURE
..........................22-6
HIGH/LOW RELAY - DESCRIPTION,
WIPER
.............................8R-20
HIGH/LOW RELAY - DIAGNOSIS AND
TESTING, WIPER
.....................8R-21
HIGH/LOW RELAY - INSTALLATION,
WIPER
.............................8R-21
HIGH/LOW RELAY - OPERATION, WIPER
. . 8R-20
HIGH/LOW RELAY - REMOVAL, WIPER
. . . 8R-21
16 INDEXDR
Description Group-Page Description Group-Page Description Group-Page

MOLDING - INSTALLATION, REAR DOOR
INNER BELT.........................23-94
MOLDING - INSTALLATION, REAR DOOR
OUTER BELT........................23-94
MOLDING - REMOVAL, FRONT DOOR
INNER BELT.........................23-93
MOLDING - REMOVAL, FRONT DOOR
OUTER BELT........................23-93
MOLDING - REMOVAL, REAR DOOR
INNER BELT.........................23-94
MOLDING - REMOVAL, REAR DOOR
OUTER BELT........................23-94
MOLDINGS - INSTALLATION, BODY SIDE . . 23-36
MOLDINGS - REMOVAL, BODY SIDE.....23-36
MONITORED SYSTEMS - DESCRIPTION....25-1
MONITORS - DESCRIPTION,
COMPONENT.........................25-4
MOTOR - DESCRIPTION, ADJUSTABLE
PEDAL..............................5-24
MOTOR - DESCRIPTION, BLOWER.......24-25
MOTOR - DESCRIPTION, DOOR LOCK.....8N-5
MOTOR - DESCRIPTION, IDLE AIR
CONTROL..........................14-33
MOTOR - DESCRIPTION, LUMBAR.......8N-19
MOTOR - DESCRIPTION, SHIFT . . 21-686,21-720
MOTOR - DIAGNOSIS AND TESTING,
BLOWER...........................24-26
MOTOR - DIAGNOSIS AND TESTING,
DOOR LOCK.........................8N-5
MOTOR - DIAGNOSIS AND TESTING,
LUMBAR...........................8N-20
MOTOR - DIAGNOSIS AND TESTING,
STARTER ...........................8F-34
MOTOR - INSTALLATION, ADJUSTABLE
PEDAL..............................5-24
MOTOR - INSTALLATION, BLOWER......24-26
MOTOR - INSTALLATION, IDLE AIR
CONTROL..........................14-35
MOTOR - INSTALLATION, SHIFT . . 21-686,21-720
MOTOR - INSTALLATION, STARTER......8F-37
MOTOR - OPERATION, BLOWER.........24-25
MOTOR - OPERATION, DOOR LOCK.......8N-5
MOTOR - OPERATION, IDLE AIR
CONTROL..........................14-33
MOTOR - OPERATION, LUMBAR........8N-20
MOTOR - OPERATION, SHIFT....21-686,21-720
MOTOR - REMOVAL, ADJUSTABLE
PEDAL..............................5-24
MOTOR - REMOVAL, BLOWER..........24-26
MOTOR - REMOVAL, IDLE AIR CONTROL . . 14-34
MOTOR - REMOVAL, SHIFT.....21-686,21-720
MOTOR - REMOVAL, STARTER..........8F-34
MOTOR - REMOVAL, WINDOW..........8N-22
MOTOR RELAY - DESCRIPTION,
STARTER ...........................8F-38
MOTOR RELAY - INSTALLATION,
STARTER ...........................8F-39
MOTOR RELAY - OPERATION, STARTER . . . 8F-38
MOTOR RELAY - REMOVAL, STARTER....8F-39
MOTOR RESISTOR - DIAGNOSIS AND
TESTING, BLOWER...................24-18
MOTOR RESISTOR BLOCK -
DESCRIPTION, BLOWER...............24-17
MOTOR RESISTOR BLOCK -
INSTALLATION, BLOWER
..............24-18
MOTOR RESISTOR BLOCK - OPERATION,
BLOWER
...........................24-17
MOTOR RESISTOR BLOCK - REMOVAL,
BLOWER
...........................24-18
MOTOR SWITCH - DESCRIPTION,
BLOWER
...........................24-18
MOTOR SWITCH - DIAGNOSIS AND
TESTING, BLOWER
...................24-18
MOTOR SWITCH - INSTALLATION,
BLOWER
...........................24-19
MOTOR SWITCH - OPERATION, BLOWER
. . 24-18
MOTOR SWITCH - REMOVAL, BLOWER
. . . 24-19
MOUNT - INSTALLATION, DISC BRAKE
CALIPER ADAPTER
....................5-17
MOUNT - INSTALLATION, FRONT
. . . 9-144,9-211,
9-265,9-335,9-392,9-58
MOUNT - INSTALLATION, REAR
....9-147,9-213,
9-267,9-337,9-393,9-60
MOUNT - REMOVAL, FRONT
. 9-144,9-211,9-264,
9-335,9-392,9-57
MOUNT - REMOVAL, REAR
. . 9-147,9-213,9-266,
9-337,9-393,9-60MOUNTED STOP LAMP - INSTALLATION,
CENTER HIGH.......................8L-10
MOUNTED STOP LAMP - REMOVAL,
CENTER HIGH.......................8L-10
MOUNTED STOP LAMP UNIT -
INSTALLATION, CENTER HIGH..........8L-10
MOUNTED STOP LAMP UNIT -
REMOVAL, CENTER HIGH..............8L-10
MOUNTING - STANDARD PROCEDURE,
MATCH .............................22-3
MUFFLER - 5.9L DIESEL - INSTALLATION . . 11-9
MUFFLER - 5.9L DIESEL - REMOVAL......11-9
MUFFLER - INSTALLATION..............11-8
MUFFLER - REMOVAL..................11-8
MULTI-FUNCTION SWITCH - DIAGNOSIS
AND TESTING.......................8L-18
MULTI-FUNCTION SWITCH -
INSTALLATION.......................8L-19
MULTI-FUNCTION SWITCH - REMOVAL . . . 8L-18
NAME PLATES - INSTALLATION,
EXTERIOR..........................23-38
NAME PLATES - REMOVAL, EXTERIOR....23-38
NATURAL VAC LEAK DETECTION ASSY -
DESCRIPTION.......................25-23
NATURAL VAC LEAK DETECTION ASSY -
INSTALLATION.......................25-24
NATURAL VAC LEAK DETECTION ASSY -
OPERATION.........................25-23
NATURAL VAC LEAK DETECTION ASSY -
REMOVAL..........................25-24
NECK SEAL - DIAGNOSIS AND TESTING,
RADIATOR CAP-TO-FILLER...............7-61
NEW MODULE / SWITCH OPERATING
MODES, STANDARD PROCEDURE -
CONFIGURING A......................8Q-3
NIGHT MIRROR - DESCRIPTION,
AUTOMATIC DAY.....................8N-12
NIGHT MIRROR - DIAGNOSIS AND
TESTING, AUTOMATIC DAY.............8N-12
NIGHT MIRROR - OPERATION,
AUTOMATIC DAY.....................8N-12
NIGHT MIRROR - REMOVAL,
AUTOMATIC DAY.....................8N-13
NOISE - DIAGNOSIS AND TESTING, A/C
COMPRESSOR.......................24-36
NOISE - DIAGNOSIS AND TESTING,
WIND...............................23-2
NOISE OR VIBRATION - DIAGNOSIS AND
TESTING, TIRE.......................22-7
NOISE SUPPRESSION GROUND STRAP -
DESCRIPTION, RADIO..................8A-8
NOISE SUPPRESSION GROUND STRAP -
INSTALLATION, RADIO................8A-10
NOISE SUPPRESSION GROUND STRAP -
OPERATION, RADIO...................8A-8
NOISE SUPPRESSION GROUND STRAP -
REMOVAL, RADIO.....................8A-9
NON-DEPLOYED SUPPLEMENTAL
RESTRAINTS - STANDARD
PROCEDURE, HANDLING...............8O-6
NON-MONITORED CIRCUITS -
OPERATION..........................25-8
NOZZLE - DESCRIPTION, WASHER......8R-12
NOZZLE - INSTALLATION, WASHER......8R-12
NOZZLE - OPERATION, WASHER........8R-12
NOZZLE - REMOVAL, WASHER..........8R-12
NUMBER - DESCRIPTION, VEHICLE
IDENTIFICATION....................Intro.-2
NV241 GENII - ASSEMBLY, TRANSFER
CASE.............................21-604
NV241 GENII - CLEANING, TRANSFER
CASE.............................21-602
NV241 GENII - DESCRIPTION, TRANSFER
CASE................................0-4
NV241 GENII - DESCRIPTION, TRANSFER
CASE.............................21-591
NV241 GENII - DIAGNOSIS AND
TESTING, TRANSFER CASE............21-592
NV241 GENII - DISASSEMBLY,
TRANSFER CASE
....................21-593
NV241 GENII - INSPECTION, TRANSFER
CASE
.............................21-602
NV241 GENII - INSTALLATION,
TRANSFER CASE
....................21-614
NV241 GENII - OPERATION, TRANSFER
CASE
.............................21-591
NV241 GENII - REMOVAL, TRANSFER
CASE
.............................21-593NV241 GENII - TRANSFER CASE........21-614
NV241/NV243 - TRANSFER CASE . 21-615,21-680
NV243 - ASSEMBLY, TRANSFER CASE . . . 21-670
NV243 - CLEANING, TRANSFER CASE . . . 21-668
NV243 - DESCRIPTION, TRANSFER CASE . . . 0-4
NV243 - DESCRIPTION, TRANSFER CASE . 21-658
NV243 - DIAGNOSIS AND TESTING,
TRANSFER CASE....................21-659
NV243 - DISASSEMBLY, TRANSFER
CASE.............................21-660
NV243 - INSPECTION, TRANSFER CASE . . 21-668
NV243 - INSTALLATION, TRANSFER
CASE.............................21-679
NV243 - OPERATION, TRANSFER CASE . . 21-659
NV243 - REMOVAL, TRANSFER CASE....21-660
NV243 - TRANSFER CASE.............21-680
NV271 - ASSEMBLY, TRANSFER CASE . . . 21-637
NV271 - CLEANING, TRANSFER CASE . . . 21-635
NV271 - DESCRIPTION, TRANSFER CASE . . . 0-4
NV271 - DESCRIPTION, TRANSFER CASE . 21-623
NV271 - DIAGNOSIS AND TESTING,
TRANSFER CASE....................21-624
NV271 - DISASSEMBLY, TRANSFER
CASE.............................21-625
NV271 - INSPECTION, TRANSFER CASE . . 21-635
NV271 - INSTALLATION, TRANSFER
CASE.............................21-649
NV271 - OPERATION, TRANSFER CASE . . 21-623
NV271 - REMOVAL, TRANSFER CASE....21-625
NV271 - TRANSFER CASE.............21-649
NV271/NV273, SPECIAL TOOLS -
TRANSFER CASE..............21-650,21-714
NV273 - ASSEMBLY, TRANSFER CASE . . . 21-701
NV273 - CLEANING, TRANSFER CASE . . . 21-698
NV273 - DESCRIPTION, TRANSFER CASE . . . 0-4
NV273 - DESCRIPTION, TRANSFER CASE . 21-687
NV273 - DIAGNOSIS AND TESTING,
TRANSFER CASE....................21-688
NV273 - DISASSEMBLY, TRANSFER
CASE.............................21-689
NV273 - INSPECTION, TRANSFER CASE . . 21-699
NV273 - INSTALLATION, TRANSFER
CASE.............................21-713
NV273 - OPERATION, TRANSFER CASE . . 21-688
NV273 - REMOVAL, TRANSFER CASE....21-689
NV273 - TRANSFER CASE.............21-713
NV3500 - ASSEMBLY, MANUAL
TRANSMISSION......................21-17
NV3500 - CLEANING, MANUAL
TRANSMISSION......................21-15
NV3500 - DESCRIPTION, MANUAL
TRANSMISSION.......................21-1
NV3500 - DIAGNOSIS AND TESTING,
MANUAL TRANSMISSION...............21-3
NV3500 - DISASSEMBLY, MANUAL
TRANSMISSION.......................21-4
NV3500 - INSPECTION, MANUAL
TRANSMISSION......................21-15
NV3500 - INSTALLATION, MANUAL
TRANSMISSION......................21-38
NV3500 - OPERATION, MANUAL
TRANSMISSION.......................21-1
NV3500 - REMOVAL, MANUAL
TRANSMISSION.......................21-3
NV3500 - SPECIAL TOOLS, MANUAL
TRANSMISSION......................21-40
NV3500 - SPECIFICATIONS, MANUAL
TRANSMISSION......................21-39
NV4500 - ASSEMBLY, MANUAL
TRANSMISSION......................21-61
NV4500 - CLEANING, MANUAL
TRANSMISSION......................21-60
NV4500 - DESCRIPTION, MANUAL
TRANSMISSION......................21-42
NV4500 - DIAGNOSIS AND TESTING,
MANUAL TRANSMISSION..............21-43
NV4500 - DISASSEMBLY, MANUAL
TRANSMISSION......................21-44
NV4500 - INSPECTION, MANUAL
TRANSMISSION
......................21-60
NV4500 - INSTALLATION, MANUAL
TRANSMISSION
......................21-77
NV4500 - OPERATION, MANUAL
TRANSMISSION
......................21-42
NV4500 - REMOVAL, MANUAL
TRANSMISSION
......................21-43
NV4500 - SPECIAL TOOLS, MANUAL
TRANSMISSION
......................21-79
22 INDEXDR
Description Group-Page Description Group-Page Description Group-Page

PRESSURE (LP) SENSOR -
INSTALLATION, LINE.................21-560
PRESSURE (LP) SENSOR - OPERATION,
LINE..............................21-559
PRESSURE (LP) SENSOR - REMOVAL,
LINE..............................21-559
PRESSURE RELEASE - STANDARD
PROCEDURE, FUEL SYSTEM.............14-2
PRESSURE RELIEF VALVE - CLEANING,
OIL................................9-343
PRESSURE RELIEF VALVE -
DESCRIPTION, HIGH..................24-35
PRESSURE RELIEF VALVE - INSPECTION,
OIL................................9-343
PRESSURE RELIEF VALVE -
INSTALLATION, OIL...................9-343
PRESSURE RELIEF VALVE - OPERATION,
HIGH..............................24-36
PRESSURE RELIEF VALVE - REMOVAL,
OIL................................9-343
PRESSURE SENSOR - DESCRIPTION,
FUEL..............................14-72
PRESSURE SENSOR - INSTALLATION,
FUEL..............................14-72
PRESSURE SENSOR - OPERATION, FUEL . . 14-72
PRESSURE SENSOR - REMOVAL, FUEL . . . 14-72
PRESSURE SENSOR/SWITCH -
DESCRIPTION, OIL....................9-66
PRESSURE SENSOR/SWITCH -
INSTALLATION, OIL...............9-343,9-67
PRESSURE SENSOR/SWITCH -
OPERATION, OIL......................9-66
PRESSURE SENSOR/SWITCH -
REMOVAL, OIL..................9-343,9-67
PRESSURE, SPECIFICATIONS - FUEL
SYSTEM............................14-3
PRESSURE SWITCH - DESCRIPTION,
POWER STEERING...................19-45
PRESSURE SWITCH - OPERATION,
POWER STEERING...................19-45
PRESSURE TEST - DIAGNOSIS AND
TESTING, HYDRAULIC....21-140,21-321,21-493
PRESSURE TRANSDUCER -
DESCRIPTION, A/C...................24-15
PRESSURE TRANSDUCER - DIAGNOSIS
AND TESTING, A/C...................24-15
PRESSURE TRANSDUCER -
INSTALLATION, A/C...................24-16
PRESSURE TRANSDUCER - OPERATION,
A/C................................24-15
PRESSURE TRANSDUCER - REMOVAL,
A/C................................24-16
PRESSURES - DESCRIPTION, TIRE
INFLATION...........................22-6
PRIMING - STANDARD PROCEDURE,
FUEL SYSTEM.......................14-59
PROGRAMING - STANDARD
PROCEDURE, RKE TRANSMITTER.......8N-10
PROGRAMMING - STANDARD
PROCEDURE, ELECTRONIC VEHICLE
INFORMATION CENTER................8M-8
PROGRAMMING - STANDARD
PROCEDURE, PCM/SKIM...............8E-14
PROGRAMMING, STANDARD
PROCEDURE - SENTRY KEY
IMMOBILIZER SYSTEM TRANSPONDER....8Q-4
PROPELLER SHAFT - DIAGNOSIS AND
TESTING.............................3-1
PROPELLER SHAFT - INSTALLATION,
FRONT...............................3-7
PROPELLER SHAFT - INSTALLATION,
REAR................................3-8
PROPELLER SHAFT - REMOVAL, FRONT....3-6
PROPELLER SHAFT - REMOVAL, REAR.....3-7
PROPELLER SHAFT - SPECIAL TOOLS......3-6
PROPELLER SHAFT - SPECIFICATIONS......3-6
PROPELLER SHAFT - STANDARD
PROCEDURE..........................3-3
PROPORTIONING - DESCRIPTION,
ELECTRONIC VARIABLE BRAKE..........5-43
PROPORTIONING - OPERATION,
ELECTRONIC VARIABLE BRAKE..........5-43
PULLEY - INSTALLATION..............19-46
PULLEY - REMOVAL
..................19-45
PUMP - 5.7L - INSTALLATION, WATER
.....7-71
PUMP - 5.7L - REMOVAL, WATER
........7-70
PUMP - 5.9L - CLEANING, WATER
........7-64
PUMP - 5.9L - DESCRIPTION, WATER
.....7-62PUMP - 5.9L - INSPECTION, WATER......7-64
PUMP - 5.9L - INSTALLATION, WATER.....7-64
PUMP - 5.9L - OPERATION, WATER.......7-62
PUMP - 5.9L - REMOVAL, WATER........7-63
PUMP - 5.9L DIESEL - CLEANING,
WATER .............................7-67
PUMP - 5.9L DIESEL - DESCRIPTION,
WATER .............................7-67
PUMP - 5.9L DIESEL - INSPECTION,
WATER .............................7-68
PUMP - 5.9L DIESEL - INSTALLATION,
WATER .............................7-68
PUMP - 5.9L DIESEL - OPERATION,
WATER .............................7-67
PUMP - 5.9L DIESEL - REMOVAL,
WATER .............................7-67
PUMP - ASSEMBLY, OIL......9-156,9-274,9-68
PUMP - ASSEMBLY, OIL . . 21-215,21-393,21-566
PUMP - CLEANING, OIL.....9-155,9-218,9-344,
9-398
PUMP - CLEANING, OIL . . 21-214,21-393,21-566
PUMP - DESCRIPTION................19-38
PUMP - DESCRIPTION, FUEL...........14-12
PUMP - DESCRIPTION, FUEL INJECTION . . 14-64
PUMP - DESCRIPTION, FUEL TRANSFER . . 14-75
PUMP - DESCRIPTION, LEAK DETECTION . 25-13
PUMP - DESCRIPTION, OIL.....21-212,21-392,
21-562
PUMP - DESCRIPTION, WATER..........7-64
PUMP - DIAGNOSIS AND TESTING,
WATER .........................7-62,7-67
PUMP - DISASSEMBLY, OIL . . . 9-155,9-272,9-67
PUMP - DISASSEMBLY, OIL.....21-212,21-393,
21-564
PUMP - INITIAL OPERATION -
STANDARD PROCEDURE, POWER
STEERING..........................19-39
PUMP - INSPECTION, OIL . . . 9-155,9-218,9-272,
9-344,9-399,9-67
PUMP - INSPECTION, OIL . 21-214,21-393,21-566
PUMP - INSTALLATION, FUEL INJECTION . 14-67
PUMP - INSTALLATION, FUEL TRANSFER . 14-76
PUMP - INSTALLATION, LEAK
DETECTION.........................25-16
PUMP - INSTALLATION, OIL . 9-157,9-219,9-274,
9-344,9-400,9-68
PUMP - OPERATION..................19-38
PUMP - OPERATION, FUEL.............14-12
PUMP - OPERATION, FUEL INJECTION....14-64
PUMP - OPERATION, FUEL TRANSFER....14-76
PUMP - OPERATION, LEAK DETECTION . . . 25-14
PUMP - OPERATION, OIL . 21-212,21-392,21-562
PUMP - OPERATION, WATER............7-64
PUMP - REMOVAL, FUEL INJECTION.....14-65
PUMP - REMOVAL, FUEL TRANSFER.....14-76
PUMP - REMOVAL, LEAK DETECTION....25-16
PUMP - REMOVAL, OIL.....9-154,9-218,9-272,
9-343,9-398,9-67
PUMP BYPASS - DESCRIPTION, WATER . . . 7-64
PUMP BYPASS - OPERATION, WATER.....7-65
PUMP BYPASS HOSE WITH AIR
CONDITIONING - INSTALLATION,
WATER .............................7-70
PUMP BYPASS HOSE WITH AIR
CONDITIONING - REMOVAL, WATER......7-68
PUMP BYPASS HOSE WITHOUT AIR
CONDITIONING - INSTALLATION,
WATER .............................7-70
PUMP BYPASS HOSE WITHOUT AIR
CONDITIONING - REMOVAL, WATER......7-69
PUMP FRONT SEAL - INSTALLATION,
OIL
...............................21-567
PUMP FRONT SEAL - REMOVAL, OIL
....21-567
PUMP LEAKAGE - DIAGNOSIS AND
TESTING
...........................19-39
PUMP MODULE - DESCRIPTION, FUEL
....14-12
PUMP MODULE - INSTALLATION, FUEL
. . . 14-13
PUMP MODULE - OPERATION, FUEL
.....14-12
PUMP MODULE - REMOVAL, FUEL
.......14-12
PUMP RELAY - DESCRIPTION, FUEL
.....14-33
PUMP RELAY - INSTALLATION, FUEL
.....14-33
PUMP RELAY - OPERATION, FUEL
.......14-33
PUMP RELAY - REMOVAL, FUEL
........14-33
PUMP RELAYS - DIAGNOSIS AND
TESTING, ASD AND FUEL
...............8I-7
PUMP TIMING - DIAGNOSIS AND
TESTING, FUEL INJECTION
.............14-65PUMP VOLUME CHECK - STANDARD
PROCEDURE, OIL...................21-563
PUMP/MOTOR - DESCRIPTION, WASHER . 8R-13
PUMP/MOTOR - INSTALLATION,
WASHER...........................8R-14
PUMP/MOTOR - OPERATION, WASHER . . . 8R-13
PUMP/MOTOR - REMOVAL, WASHER....8R-14
PUSHRODS - CLEANING...............9-301
PUSHRODS - INSPECTION.............9-302
QUAD CAB - INSTALLATION............8O-32
QUAD CAB - REMOVAL................8O-29
QUICK CONNECT FITTING -
DESCRIPTION........................14-8
QUICK LEARN - STANDARD
PROCEDURE, TCM...................8E-21
QUICK-CONNECT FITTINGS - STANDARD
PROCEDURE.........................14-8
RADIAL - PLY TIRES - DESCRIPTION......22-6
RADIATOR - 5.9L DIESEL - CLEANING.....7-60
RADIATOR - 5.9L DIESEL -
DESCRIPTION........................7-59
RADIATOR - 5.9L DIESEL - INSPECTION . . . 7-60
RADIATOR - 5.9L DIESEL -
INSTALLATION........................7-60
RADIATOR - 5.9L DIESEL - OPERATION....7-59
RADIATOR - 5.9L DIESEL - REMOVAL.....7-59
RADIATOR - CLEANING.................7-58
RADIATOR - DESCRIPTION..............7-56
RADIATOR - INSPECTION.................7-58
RADIATOR - INSTALLATION.............7-58
RADIATOR - OPERATION................7-56
RADIATOR - REMOVAL.................7-57
RADIATOR CAP - DIAGNOSIS AND
TESTING............................7-61
RADIATOR CAP-TO-FILLER NECK SEAL -
DIAGNOSIS AND TESTING..............7-61
RADIATOR COOLANT FLOW -
DIAGNOSIS AND TESTING..........7-57,7-59
RADIATOR CROSSMEMBER -
INSTALLATION, UPPER................23-42
RADIATOR CROSSMEMBER - REMOVAL,
UPPER.............................23-42
RADIATOR FAN - 5.9L DIESEL -
CLEANING...........................7-41
RADIATOR FAN - 5.9L DIESEL -
INSPECTION.........................7-41
RADIATOR FAN - 5.9L DIESEL -
INSTALLATION........................7-41
RADIATOR FAN - 5.9L DIESEL -
REMOVAL...........................7-41
RADIATOR FAN - CLEANING.............7-40
RADIATOR FAN - INSPECTION...........7-40
RADIATOR FAN - INSTALLATION..........7-40
RADIATOR FAN - REMOVAL.............7-39
RADIATOR PRESSURE CAP -
DESCRIPTION........................7-60
RADIATOR PRESSURE CAP - OPERATION . . 7-61
RADIO - DESCRIPTION.................8A-7
RADIO - INSTALLATION................8A-8
RADIO - OPERATION...................8A-7
RADIO - REMOVAL....................8A-7
RADIO NOISE SUPPRESSION GROUND
STRAP - DESCRIPTION.................8A-8
RADIO NOISE SUPPRESSION GROUND
STRAP - INSTALLATION...............8A-10
RADIO NOISE SUPPRESSION GROUND
STRAP - OPERATION..................8A-8
RADIO NOISE SUPPRESSION GROUND
STRAP - REMOVAL....................8A-9
RAIL - DESCRIPTION, FUEL
............14-13
RAIL - DESCRIPTION, FUEL INJECTOR
....14-89
RAIL - INSTALLATION, FUEL
............14-18
RAIL - INSTALLATION, FUEL INJECTOR
. . . 14-90
RAIL - OPERATION, FUEL
..............14-13
RAIL - OPERATION, FUEL INJECTOR
.....14-89
RAIL - REMOVAL, FUEL
...............14-13
RAIL - REMOVAL, FUEL INJECTOR
.......14-89
RAIL REPAIR - STANDARD PROCEDURE,
HYDROFORM FENDER
.................13-12
RAIL TIP REPLACEMENT - STANDARD
PROCEDURE, LIGHT DUTY FRONT
FRAME
..............................13-4
RAIL WEATHERSTRIP - INSTALLATION,
DRIP
..............................23-91
RAIL WEATHERSTRIP - REMOVAL, DRIP
. . 23-91
RAIL WEATHERSTRIP RETAINER -
INSTALLATION, DRIP
.................23-92
26 INDEXDR
Description Group-Page Description Group-Page Description Group-Page