2003 DAEWOO MATIZ wiring

ENGINE CONTROLS 1F–215
DAEWOO M-150 BL2

The EVAP system in unable to achieve or maintain
vacuum during the diagnostic test. The amount of
decay will vary within the fuel level.
Action Taken When the DTC Sets

The Malfunction Indicator Lamp (MIL) will illuminate.

The ECM will record operating conditions at the time
the diagnostic fails. This information will be stored in
the Freeze Frame and Failure Records buffers.

A history DTC is stored.

Coolant fan turns ON.
Conditions for Clearing the MIL/DTC

The MIL will turn off after four consecutive ignition
cycles in which the diagnostic runs without a fault.

A history DTC will clear after 40 consecutive warm-up
cycles without a fault.

DTC(s) can be cleared by using the scan tool.
Diagnostic Aids
Although this DTC is considered a type. A diagnostic, it
acts like a type B diagnostic under certain conditions.
Whenever this diagnostic reports the system has
passed, or if the battery is disconnected, the diagnostic
must fail twice before setting a DTC. The initial failure is
not reported to the diagnostic executive or displayed ona scan tool. A passing system always reports to the
diagnostic executive immediately.
Check for the following conditions :
Missing or damaged fuel cap.
Missing or damaged O-rings at fuel vapor and EVAP
purge line canister fittings.
Cracked or punctured EVAP canister.
Damaged source vacuum line, EVAP purge line, EVAP
vent hose or fuel tank vapor line.
Poor connection at the ECM. Inspect the harness con-
nectors for the following conditions.

Backed-out terminals.

Improper mating.

Broken locks.

Improperly formed.

Damaged terminals.

Poor terminal-to-wire connection.

Damaged harness. Inspect the wiring harness to the
EVAP vent solenoid, EVAP canister purge valve, and
the fuel tank pressure sensor for an intermittent open
or short circuit.

Kinked, pinched or plugged vacuum source, EVAP
purge, or fuel tank vapor line. Verify that the lines are
not restricted.
DTC P0445 – EVAP Purge Control Circuit Fault
StepActionValue(s)YesNo
1
Perform an Euro On-Board Diagnostic (EOBD)
System Check.
Is the system check complete?
–
Go to Step 2
Go to
“On-Board
Diagnostic
System Check”
2
1. Disconnect the evaporative emission (EVAP)
canister purge valve connector.
2. Measure the resistance of the EVAP canister
purge valve connector.
Does the resistance measure near within the value
specified?
30ΩGo to Step 3Go to Step 9
3
Connect a test light between EVAP canister purge
valve connector terminal 2 and ground.
Is the test light ON?
–
Go to Step 4Go to Step 6
4
1. Disconnect the ECM connector.
2. Connect a test light between the ECM connector
terminal 66 and ground.
Is the test light ON?
–
Go to Step 5Go to Step 7

1F–218 ENGINE CONTROLS
DAEWOO M-150 BL2
MAA1F250
DIAGNOSTIC TROUBLE CODE (DTC) – P0462 FUEL LEVEL SENSOR LOW
V O LTA G E
Circuit Description
The engine control module(ECM) uses the fuel level in-
put from the Fuel Level Sensor to calculate expected va-
por pressures within the fuel system. Vapor pressure
vary as the fuel level changes. Vapor pressure is critical
in determining if the evaporative emission (EVAP) sys-
tem is operating properly. Fuel Level is also used to de-
termine if the Fuel level is too high or too low to be able
to accurately detect EVAP system faults. This Diagnos-
tic Trouble Code(DTC) detects a stuck fuel level sender.
Conditions for Setting the DTC

Fuel Level Sensor voltage is less than 0.05V.

Fuel Level Sensor circuit low voltage.
Action Taken When The DTCs Sets

The Malfunction Indicator Lamp (MIL) will not illumi-
nate.

The ECM will store conditions which were present
when the DTC was set as Failure Records data only.

This information will not be stored in the Freeze
Frame data.Conditions for Clearing the MIL/DTC

A history DTC will clear after 40 consecutive warm-up
cycles without a fault.

DTC(s) can be cleared by using the scan tool.
Diagnostic Aids
Inspect harness connectors for backed-out terminal, im-
proper mating, broken locks, improperly formed or dam-
aged terminals, and poor terminal-to-wire connection.
Inspect the wiring harness for damage.
A stuck Fuel Level Sensor may cause the DTC to set. If
DTC P0463 cannot be duplicated, the information in-
cluded in the Freeze Frame data can be useful in deter-
mining vehicle operating conditions when the DTC was
first set.
Resistance check for the Fuel Level Sensor.
Empty = 100 ohms or over.
Half full = about 32.5 ohms.
Full = 10 ohms or less.

1F–222 ENGINE CONTROLS
DAEWOO M-150 BL2
MAA1F250
DIAGNOSTIC TROUBLE CODE (DTC) – P0463 FUEL LEVEL SENSOR HIGH
V O LTA G E
Circuit Description
The engine control module(ECM) uses the fuel level in-
put from the Fuel Level Sensor to calculate expected va-
por pressures within the fuel system. Vapor pressure
vary as the fuel level changes. Vapor pressure is critical
in determining if the evaporative emission (EVAP) sys-
tem is operating properly. Fuel Level is also used to de-
termine if the Fuel level is too high or too low to be able
to accurately detect EVAP system faults. This Diagnos-
tic Trouble Code(DTC) detects a stuck fuel level sender.
Conditions for Setting the DTC

Fuel Level Sensor voltage is higher than 4.9V.

Fuel Level Sensor circuit high voltage.
Action Taken When the DTC Sets

The Malfunction Indicator Lamp (MIL) will not illumi-
nate.

The ECM will store conditions which were present
when the DTC was set as Failure Records data only.

This information will not be stored in the Freeze
Frame data.Conditions for Clearing the MIL/DTC

A history DTC will clear after 40 consecutive warm-up
cycles without a fault.

DTC(s) can be cleared by using the scan tool.
Diagnostic Aids
Inspect harness connectors for backed-out terminal, im-
proper mating, broken locks, improperly formed or dam-
aged terminals, and poor terminal-to-wire connection.
Inspect the wiring harness for damage.
A stuck Fuel Level Sensor may cause the DTC to set. If
DTC P0463 cannot be duplicated, the information in-
cluded in the Freeze Frame data can be useful in deter-
mining vehicle operating conditions when the DTC was
first set.
Resistance check for the Fuel Level Sensor.
Empty = 100 ohms or over.
Half full = about 32.5 ohms.
Full = 10 ohms or less.

1F–242 ENGINE CONTROLS
DAEWOO M-150 BL2
MAA1F280
DIAGNOSTIC TROUBLE CODE (DTC) – P0501 VEHICLE SPEED NO SIGNAL
(M/T ONLY)
Circuit Description
Vehicle speed information is provided to the engine con-
trol module (ECM) by the voltage speed sensor (VSS) is
a permanent magnet generator that is mounted in the
transaxle and produces a pulsing voltage whenever ve-
hicle speed is over 3 mph (5km/h). The A/C voltage level
and the number of pulses increase with vehicle speed.
The ECM converts the pulsing voltage into mph (km/h)
and than supplies the necessary signal to the instrument
panel for speedometer / odometer operation and to the
cruise control module and multi-function alarm module
operation. The Diagnostic Trouble Code (DTC) will de-
tect if vehicle speed is reasonable according to engine
rpm and load.
Conditions for Setting the DTC

Vehicle speed is not change at least 10 seconds.

Engine speed is greater than 2,100rpm.

MAF is greater than 152mg/tdc.
Action taken when The DTCs Sets

The Malfunction Indicator Lamp (MIL) will illuminate.

The ECM will record operating conditions at the time
the diagnostic fails. This information will be stored in
the Freeze Frame and failure records buffers.

A history DTC is stored.Conditions for Clearing the MIL/DTC

The MIL will turn off after four consecutive ignition
cycles in which the diagnostic runs without a fault.

A history DTC will clear after 40 consecutive warm up
cycles without a fault.

Using the scan tool can clear DTC(s).
Diagnostic Aids
An Intermittent problem may be caused by a poor con-
nection, rubbed through wire insulation, or wire that is
broken inside the insulation.
VSS signal circuit should be thoroughly checked for the
following conditions

Backed-out terminals

Improper mating

Broken locks

Improperly formed

Damaged terminals

Poor terminals to wire connection

Physical damage to the wiring harness
Ensure the VSS is correctly torqued to the trnasaxle
housing.
Refer to “intermittents” in this Section.

1F–246 ENGINE CONTROLS
DAEWOO M-150 BL2
MAA1F070
DIAGNOSTIC TROUBLE CODE (DTC) 0505
IDLE AIR CONTROL VALVE (IACV) CIRCUIT FAULT
Circuit Description
The Engine Control Module (ECM) controls the air en-
tering into the engine with an Idle Air Control (IAC)
Valve. To increase the idle rpm, the ECM commands the
pintle inside the IAC valve away from the throttle body
seat. This allows more air to bypass through the throttle
blade. To decrease the rpm the ECM commands the
pintle towards the throttle body seat. This reduces the
amount of air bypassing the throttle blade. A scan tool
will read the IAC valve pintle position in counts. The
higher the counts, the more air that is allowed to bypass
the throttle blade. This Diagnostic Trouble Code (DTC)
determines if a low idle condition exists as defined as
100 rpm below the desired idle rpm.
Conditions for Setting the DTC

No intrusive tests are active.

DTC(s) P0106, P0107, P0108, P0112, P0113,
P0117, P0118, P0122, P0123, P0131, P0132,
P0133, P1133, P1134, P0171, P1171, P0172, P0201,
P0202, P0203, P0204, P0300, P0336, P0337,
P0341, P0342, P0351, P0352, P0402, P0404,
P1404, P0405, P0406, P0443, and P0502 are not
set.

Engine is running more than 60 seconds.

Barometric Pressure (BARO) is greater than 72 kPa
(10.4 psi).

Engine Coolant Temperature (ECT) is greater than
60C (140F).

Ignition voltage is between 11 and 16 volts.

The Intake Air Temperature (IAT) is greater than
–20C (–4F).

Manifold Absolute Pressure is less than 60 kPa (8.7
psi).
IAC valve is controlled fully opened.

All of the above must be met for greater than 5 sec-
onds.
Action Taken When the DTC Sets

The Malfunction Indicator Lamp (MIL) will illuminate.

The ECM will record operating conditions at the time
the diagnostic fails. This information will be stored in
the Freeze Frame and Failure Records buffers.

A history DTC is stored.
Conditions for Clearing the MIL/DTC

The MIL will turn off after four consecutive ignition
cycles in which the diagnostic runs without a fault.

A history DTC will clear after 40 consecutive warm-up
cycles without a fault.

DTC(s) can be cleared by using the scan tool.

Disconnecting the ECM battery feed for more than 10
seconds.
Diagnostic Aids
Inspect the IAC valve electrical connection for proper
mating.
Inspect the wiring harness for damage.
Inspect the throttle stop screw for signs of tampering.
Inspect the throttle linkage for signs of binding or exces-
sive wear.
A slow or unstable idle may be caused by one of the fol-
lowing conditions:

Fuel system too rich or too lean.

Foreign material in the throttle body bore or in the air
induction system.

A leaking or restricted intake manifold.

ENGINE CONTROLS 1F–251
DAEWOO M-150 BL2
DTC P1535 – Evaporator Temperature Sensor High Voltage
StepActionValue(s)YesNo
1
Perform an On-Board Diagnostic (EOBD II) System
Check.
Is the system check complete?
–
Go to Step 2
Go to
“On-Board
Diagnostic
System Check”
2
1.. Turn the ignition switch to LOCK.
2. Disconnect the evaporator temperature sensor.
3. Measure the resistance between evaporator
temperature sensor terminals 1 and 2.
Does the resistance within the specified value?
0ΩGo to Step 7Go to Step 3
3
1. Turn the ignition switch to LOCK.
2. With the test light, connected to ground, probe
the ignition feed circuit, at terminal 2 in the sensor
harness connector.
Does the test light illuminate?
–
Go to Step 4Go to Step 5
4
Repair a short to battery between the terminal 46 of
ECM and A/C compressor relay terminal 2.
Is the repair complete?
–
Go to Step 9
–
5
1. Turn the ignition switch to LOCK.
2. Disconnect the ECM.
3. With the test light, connected to ground, probe
the ignition feed circuit, at terminal 2 in the sensor
harness connector.
Does the test light illuminate?
–
Go to Step 6Go to Step 8
6
Repair a short to battery between the ECM wiring
connector terminal 46 and evaporator temperature
sensor terminal 2.
Is the repair complete?
–
Go to Step 9
–
7Replace the evaporator temperature sensor.
Is the replacement complete?–Go to Step 9–
8
1. Turn the ignition switch to LOCK.
2. Replace the ECM.
Is the repair complete?
–
Go to Step 9
–
9
1. Using the scan tool, clear the Diagnostic Trouble
Codes(DTCs)
2. Start the engine and idle at normal operating
temperature.
3. Operate the vehicle within the conditions for
setting this DTC as specified in the supporting
text.
Does the scan tool indicate that this diagnostic has
run and passed?
–
Go to Step 10Go to Step 2
10
Check if any additional DTCs are set.
Are any DTCs displayed that that have not been
diagnosed?
–
Go to
applicable DTC
table
System OK

ENGINE CONTROLS 1F–253
DAEWOO M-150 BL2
DTC P1536 – Evaporator Temperature Sensor Low Voltage
StepActionValue(s)YesNo
1
Perform an On-Board Diagnostic (EOBD II) System
Check.
Is the system check complete?
–
Go to Step 2
Go to
“On-Board
Diagnostic
System Check”
2
2.. Turn the ignition switch to LOCK.
2. Disconnect the evaporator temperature sensor.
3. Measure the resistance between evaporator
temperature sensor terminals 1 and 2.
Does the resistance within the specified value?
0ΩGo to Step 7Go to Step 3
3
1. Turn the ignition switch to LOCK.
2. With the test light, connected to ground, probe
the ignition feed circuit, at terminal 2 in the sensor
harness connector.
Does the test light illuminate?
–
Go to Step 4Go to Step 5
4
Repair a short to battery between the terminal 46 of
ECM and A/C compressor relay terminal 2.
Is the repair complete?
–
Go to Step 9
–
5
1. Turn the ignition switch to LOCK.
2. Disconnect the ECM.
3. With the test light, connected to ground, probe
the ignition feed circuit, at terminal 2 in the sensor
harness connector.
Does the test light illuminate?
–
Go to Step 6Go to Step 8
6
Repair a short to battery between the ECM wiring
connector terminal 46 and evaporator temperature
sensor terminal 2.
Is the repair complete?
–
Go to Step 9
–
7Replace the evaporator temperature sensor.
Is the replacement complete?–Go to Step 9–
8
1. Turn the ignition switch to LOCK.
2. Replace the ECM.
Is the repair complete?
–
Go to Step 9
–
9
1. Using the scan tool, clear the Diagnostic Trouble
Codes(DTCs)
2. Start the engine and idle at normal operating
temperature.
3. Operate the vehicle within the conditions for
setting this DTC as specified in the supporting
text.
Does the scan tool indicate that this diagnostic has
run and passed?
–
Go to Step 10Go to Step 2
10
Check if any additional DTCs are set.
Are any DTCs displayed that that have not been
diagnosed?
–
Go to
applicable DTC
table
System OK

1F–254 ENGINE CONTROLS
DAEWOO M-150 BL2
MAA1F310
DIAGNOSTIC TROUBLE CODE (DTC) – P1537 A/C COMPRESSOR RELAY HIGH
V O LTA G E
Circuit Description
The A/C system uses an A/C refrigerant pressure sen-
sor mounted in the high pressure side of the A/C refrig-
erant system to monitor A/C refrigerant pressure. The
engine control module (ECM) uses this information to
turn ON the engine coolant fans when the A/C refriger-
ant pressure is high and to keep the compressor disen-
gaged when A/C refrigerant pressure is excessively high
or low.
Conditions for Setting the DTC

A/C compressor relay circuit short to battery.
Action Taken When the DTC Sets

The Malfunction Indicator Lamp (MIL) will not illumi-
nate.

The ECM will store conditions which were present
when the DTC was set as Failure Records data only.

This information will not be stored in the Freeze
Frame data.Conditions for Clearing the MIL/DTC

A history DTC will clear after 40 consecutive warm-up
cycles without a fault.

DTC(s) can be cleared by using the scan tool.
Diagnostic Aids
Inspect harness connectors for backed-out terminals,
improper mating, broken locks, improperly formed or
damaged terminals, and poor terminal-to-wire connec-
tion at the ECM.
Inspect the wiring harness for damage. If the harness
appears to be OK, observe the A/C pressure display on
the scan tool while moving the connectors and wiring
harnesses related to the ACP sensor. A change in the
A/C pressure display will indicate the location of the
fault.
If DTC P1537 cannot be duplicated, reviewing the Fail
Records vehicle mileage since the diagnostic test last
failed may help determine how often the condition that
caused the DTC to set occurs. This may assist in diag-
nosing the condition.