2003 DAEWOO MATIZ wiring

1F–320 ENGINE CONTROLS
DAEWOO M-150 BL2
ECM WIRING DIAGRAM (SIRIUS D3 – 1 OF 5)
MAA1F610

ENGINE CONTROLS 1F–321
DAEWOO M-150 BL2
ECM WIRING DIAGRAM (SIRIUS D3 – 2 OF 5)
MAA1F620

1F–322 ENGINE CONTROLS
DAEWOO M-150 BL2
ECM WIRING DIAGRAM (SIRIUS D3 – 3 OF 5)
MAAF630

ENGINE CONTROLS 1F–323
DAEWOO M-150 BL2
ECM WIRING DIAGRAM (SIRIUS D3 – 4 OF 5)
MAA1F640

1F–324 ENGINE CONTROLS
DAEWOO M-150 BL2
ECM WIRING DIAGRAM (SIRIUS D3 – 5 OF 5)
MAA1F650

HYDRAULIC BRAKES 4A–5
DAEWOO M-150 BL2
WARNING LAMP OPERATION
This brake system uses a BRAKE warning lamp located
in the instrument panel cluster. When the ignition switch
is in the III position, the BRAKE warning lamp should
glow and then go OFF when the ignition switch returns
to the II position.The following conditions will activate the BRAKE lamp:

Parking brake applied. The light should be on when-
ever the parking brake is applied and the ignition
switch is II.

Low fluid level. A low fluid level in the master cylinder
will turn the BRAKE lamp ON.
BRAKE SYSTEM FAULT
Condition Probable cause Correction
Brake Warning Lamp ON
Brake fluid leaks.
Repair the leaks or add th fluid.

Parking brake switch shorted to
ground.
Repair the short ground.

Faulty the fluid level sensor.
Replace the sensor.
Stoplamp ON
Faulty the stoplamp switch.
Replace the stoplamp switch.

Push rod length is short.
Adjust the push rod length of the
power booster.

Stoplamp switch circuit shorted to
battery.
Repair or Replace the wiring harness.
Poor Braking
Brake fluid lacks or leaks.
Repair the leaks or add the fluid.

Brake fluid contamination.
Replace the fluid.

Air in the brake system.
Bleed the brake system.

Damaged brake lines.
Replace the brake lines.

Damaged vacuum hose or faulty
check valve.
Replace the vacuum hose or check
value.
Dragging Brake
No free play at the brake pedal.
Adjust the free play.

Weakened the brake pedal return
spring.
Replace the return spring.

Faulty master cylinder.
Replace the master cylinder.

Air in the brake system.
Bleed the brake system.
Pedal Over Stroke
Brake fluid lacks or leaks.
Repair the leaks or add the fluid.

Poor adjustment of the brake pedal
free play.
Adjust the push rod length of the
power booster.

ANTILOCK BRAKE SYSTEM 4F–3
DAEWOO M-150 BL2
DESCRIPTION AND OPERATION
ABS SYSTEM COMPONENTS
The Antilock Braking System (ABS) consists of a con-
ventional hydraulic brake system plus antilock compo-
nents. The conventional brake system includes a
vacuum booster, master cylinder, front disc brakes, rear
drum brakes, interconnecting hydraulic brake pipes and
hoses, brake fluid level sensor and the BRAKE indicator.
The ABS components include a hydraulic unit, an elec-
tronic brake control module (EBCM), two system fuses,
four wheel speed sensors (one at each wheel), intercon-
necting wiring, the ABS indicator, and the rear drum
brake. See “ABS Component Locator” in this section for
the general layout of this system.
HYDRAULIC UNIT
The hydraulic unit with the attached EBCM is located
between the surge tank and the fire wall on the right side
of the vehicle. The basic hydraulic unit configuration
consists of return pump motor, return pump, four isola-
tion valves, four dump valves, two Low Pressure Accu-
mulators (LPA), two High Pressure Attenuators (HPA).
The hydraulic unit controls hydraulic pressure to the
front calipers and rear wheel cylinders by modulating hy-
draulic pressure to prevent wheel lockup.
Isolation valve
The isolation valve is placed in the brake fluid path from
the master cylinder to the relevant brake caliper and al-
lows free flow as commanded by the driver during nor-
mal braking and reapply phases.
In the isolation phase the coil moves the armature down,
which closes the normally open isolation orifice and pre-
vents any further increase of pressure in the brake. The
valve also remains closed during the dump phase.
The lip seal provides a one way return path for brake
fluid to flow through in:
1. Foot off pedal during isolation.
2. Residual LPA fluid.
D107E002
Dump Valve
The dump valve creates a flow path from the isolation
cartridge (brake side) to the low pressure accumulator
(LPA). The valve keeps this path permanently closed ex-
cept during the dump phase in the ABS mode. On ac-
tivation (dump phase), the coil moves up the armature
which opens the normally closed dump orifice and allow
to drain the pressure in the brake line with the brake fluid
flowing into the LPA.
The lip seal provides a return path for residual brake
fluid in the LPA.
D107E003
Low Pressure Accumulator (LPA)
LPA provides a variable chamber for brake fluid to be
quickly pushed in through the dump valve at the begin-
ning of a departure. This chamber then acts as a reser-
voir which buffers the pump.
D107E004
High Pressure Attenuator (HPA)
The HPA is in between the pump and the ISO valve
(master cylinder side) and uses the bulk mode of the
contained plastic damper and orifice size to dump out
the pressure oscillations from the pump to reduce the

4F–16 ANTILOCK BRAKE SYSTEM
DAEWOO M-150 BL2
DIAGNOSTIC INFORMATION AND PROCEDURES
D17E301A
DIAGNOSTIC TROUBLE CODE (DTC) 0354
LEFT FRONT WHEEL SPEED SENSOR CIRCUIT OPEN OR SHORTED
Circuit Description
As a toothed ring passes by the wheel speed sensor,
changes in the electromagnetic field cause the wheel
speed sensor to produce a sinusoidal (AC) voltage sig-
nal whose frequency is proportional to the wheel speed.
The magnitude of this signal is directly related to wheel
speed and the proximity of the wheel speed sensor to
the toothed ring often referred to as the air gap.
Diagnosis
This test detects a short to battery, ground, or open in
the left front wheel speed sensor circuit.
Cause(s)

The wheel speed circuit is open or shorted to the bat-
tery or ground.

There is a loose connection in the wheel speed cir-
cuit.

The wheel speed sensor resistance is very high.

The EBCM is malfunctioning.Fail Action
This is a critical operational fault. The ABS is disabled
and the ABS warning lamp is turned on. The proportion-
ing is operation.
Diagnostic Aids
An ‘‘intermittent’’ malfunction may be caused by a poor
connection, rubbed through wire insulation, or a wire
that is broken inside the insulation.
Thoroughly check any circuitry suspected of causing the
intermittent complaint. Look for backed out terminals,
improper mating, broken locks, improperly formed or
damaged terminals, poor terminal to wiring connections,
or physical damage to the wiring harness.
Wheel speed sensor resistance will increase as the sen-
sor temperature increases.
When replacing a wheel speed sensor, inspect the sen-
sor terminals and harness connector for corrosion and/
or water intrusion. If evidence of corrosion or water