2003 DAEWOO MATIZ timing belt

1B –12 SOHC ENGINE MECANICAL
DAEWOO M-150 BL2
D102B310
5. If the ignition timing exceeds the specified value,
loosen the distributor bolts and adjust it to the speci-
fied ignition timing by turning the distributor body (s).
D102B311
VA LV E T I M I N G C H E C K A N D
ADJUSTMENT
Check the valve timing in the following procedures:
1. After removing the high headlamp, loosen the bolts
(a) and remove the timing belt front upper cover (b).
D102B312
2. Turning the crankshaft clockwise twice, align the
notch (d) on the crankshaft pulley (c) with the mark 0
(e) for the timing check on the timing belt front lower
cover.
D102B313
3. Check if the notch (f) on the camshaft sprocket is
aligned with the triangle pointer (g) on the timing belt
rear cover.
Important: Notch (f) should be aligned with pointer (g)
to set the valve timing normally.
D102B314

SOHC ENGINE MECANICAL 1B–13
DAEWOO M-150 BL2
Adjust the valve timing in the following procedures:
1. Loosen the bolt and remove the timing belt pulley (c).
In loosening the bolt, use the driver (h) in the picture
shown.
D102B315
2. Remove the oil level gauge guide tube (i) and the tim-
ing belt front lower cover (j).
D102B316
3. Remove the timing belt tensioner (k) and the timing
belt (l).
D102B317
4. Using the bolt, turn the crankshaft clockwise to align
the mark (m) on the crankshaft sprocket with the
pointer (n) on the oil pump housing. Then, turn the
camshaft to align the notch (f) with the pointer (g).
D102B318
5. Install the timing belt (l) and the tensioner (k). (Do not
tighten the tensioner bolt completely.)
Turning the crankshaft clockwise twice, align the
mark (m) with the pointer (n) and tighten the tensioner
bolt to 15–23 N
m (11–17 lb-ft).
D12B319A
6. Install all removed parts.

1D – 2 ENGINE COOLING
DAEWOO M-150 BL2
DESCRIPTION AND OPERATION
GENERAL DESCRIPTION
The cooling system maintains the engine temperature at
an efficient level during all engine operating conditions.
When the engine is cold the cooling system cools the
engine slowly or not at all. This slow cooling of the en-
gine allows the engine to warm up quickly.
The cooling system includes a radiator(a) and cooling
fan(b), a thermostat and housing(c), a coolant pump(d),
a coolant pump drive belt and coolant hose. The timing
belt drives the coolant pump.
All components must function properly in order for the
cooling system to operate. The coolant pump draws the
coolant from the radiator. The coolant then circulates
through water jackets in the engine block and the cylin-
der head, distributor case(e), throttle body(f). When the
coolant reaches the operating temperature of the ther-
mostat, the thermostat opens. The coolant then goes
back to the radiator where it cools.
This system directs some coolant through the hoses to
the heater core(g). This provides for heating and de-
frosting. The surge tank(h) is connected to the radiator
and throttle body to recover the coolant displaced by ex-
pansion from the high temperatures. The surge tank
maintains the correct coolant level.
The cooling system for this vehicle has no radiator cap
and drain cock. The coolant is added to the cooling sys-tem through the surge tank. To drain the cooling system,
disconnect the lower radiator hose and drain the cool-
ant.
RADIATOR
This vehicle has a lightweight tube-and-fin aluminum ra-
diator.
SURGE TANK
The surge tank is a transparent plastic reservoir, similar
to the windshield washer reservoir.
The surge tank is connected to the radiator and throttle
body by a hose. As the vehicle is driven, the engine cool-
ant heats and expands. The portion of the engine cool-
ant displaced by this expansion flows from the radiator
into the surge tank. The air trapped in the radiator is de-
gassed into the surge tank.
When the engine is stops, the engine coolant cools and
contracts. The displaced engine coolant is then drawn
back into the radiator. This keeps the radiator filled with
the coolant to the desired level at all times and increases
the cooling efficiency.
Maintain the coolant level between the MIN and the
MAX marks on the surge tank when the system is cold.
D102D001

1D–8 ENGINE COOLING
DAEWOO M-150 BL2
COOLING SYSTEM DIAGNOSIS
Condition Probable Cause Correction
Engine OverheatsA loss of the coolant.Add the coolant.
A weak coolant solution.Confirm that the coolant solution is a
50/50 mixture of ethylene glycol and
water.
Any dirt, any leaves, or any insects
on the front of the radiator.Clean the front of the radiator.
The leakage from the hoses, the
coolant pump, the heater, the
thermostat housing, the radiator, the
heater core, or the head gasket.Replace any damaged components.
A faulty thermostat.Replace a damaged thermostat.
Retarded ignition timing.Perform an ECM code diagnosis.
Confirm the integrity of the timing
belt.
An improperly operating electric
cooling fan.Replace the electric cooling fan.
Plugged or rotted radiator hoses.Replace any damaged radiator
hoses.
A faulty water pump.Replace a faulty water pump.
A faulty surge tank cap.Replace a faulty surge tank cap.
A cracked or plugged cylinder head
or engine block.Repair the damaged cylinder head or
the damaged engine block.
A faulty radiator.Replace a faulty radiator.
Loss of CoolantA leak in the radiator.Replace a damaged radiator.
A leak in the surge tank or the hose.Replace the surge tank or the hose.
Looseness or damage of radiator
hoses, heater hoses, or connections.Reseat the hoses.
Replace the hoses or the clamps.
Leaks in the coolant pump seal.Replace the coolant pump seal.
Leaks in the coolant pump gasket.Replace the coolant pump gasket.
An improper cylinder head torque.Tighten the cylinder head bolts to
specifications.
Replace the cylinder head gasket, if
needed.
Leaks in the intake manifold, cylinder
head gasket, heater core.Repair or replace any components,
as needed to correct the leak.
Engine Fails to Reach
Normal OperatingThermostat to be stuck open or to be
wrong type.Install a new thermostat of the
correct type and heat range.
Temperature or Cool Air
from the HeaterThe coolant level below the MIN
mark on the surge tank.Add sufficient coolant to raise the
fluid to the specified mark on the
surge tank.

ENGINE COOLING 1D–15
DAEWOO M-150 BL2
D102D517
ENGINE COOLANT TEMPERATURE
SENSOR
Removal Procedure
1. Disconnect the negative battery cable.
2. Disconnect the lower radiator hose and drain the
coolant “Draining and Refilling the Cooling System” in
this section.
3. Remove the engine coolant temperature (ECT) sen-
sor.
Disconnect the electrical connector (1).
Remove the ECT sensor (2).
D12D518A
20 Nm
Installation Procedure
1. Install the ECT sensor.
Tighten
Tighten the ECT sensor to 20 Nm (15 lb-ft).
Connect the electrical connector to the ECT sen-
sor (1).
2. Connect the lower radiator hose and refill the coolant.
Refer to “Draining and Refilling the Cooling System”
in this section.
3. Connect the negative battery cable.
D102B533
COOLANT PUMP
Removal Procedure
1. Disconnect the negative battery cable.
2. Disconnect the lower radiator hose and drain the
coolant. Refer to “Draining and Refilling the Cooling
System” in this section.
3. Remove the timing belt. Refer to Section 1B, Engine
Mechanical.
4. Remove the rear timing belt cover.
Remove the bolts (1).
Remove the rear timing belt cover (2).
D102D519
5. Remove the coolant pump.
Remove the nuts (1).
Remove the bolts (2).
Remove the coolant pump (3).
Remove the gasket.
Notice: Remove the coolant pump as shown figure (a).

1D–16 ENGINE COOLING
DAEWOO M-150 BL2
9–12 Nm
9–12 Nm
D12D520A
D12D521A
Installation Procedure
1. Install the coolant pump with the new gasket.
Tighten
Tighten the bolts and the nuts to 9–12 Nm (80–106
lb-in) (a).
2. Install the rear timing belt cover.
Tighten
Tighten the bolts to 9–12 Nm (80–106 lb-in) (b).
3. Install the timing belt. Refer to Section 1B, Engine
Mechanical.
4. Connect the lower radiator hose and drain the cool-
ant. Refer to “Draining and Refilling the Cooling Sys-
tem” in this section.
5. Connect the negative battery cable.

ENGINE CONTROLS 1F–25
DAEWOO M-150 BL2
ENGINE CRANKS BUT WILL NOT RUN
Caution: Use only electrically insulated pliers when
handling ignition wires with the engine running to
prevent an electrical shock.
Caution: Do not pinch or restrict nylon fuel lines.
Damage to the lines could cause a fuel leak, result-
ing in possible fire or personal injury.Important: If a no start condition exists, ensure the fuel
cutoff switch has not been tripped prior to further diagno-
sis.
Engine Cranks But Will Not Run
StepActionValue(s)YesNo
1
Perform an Euro On-Board Diagnostic (EOBD)
System Check.
Is the check complete.
–
Go to Step 2
Go to “Euro
On-Board
Diagnostic
System Check”
2Crank the engine.
Does the engine start and continue to run?–System OkGo to Step 3
3
Perform a cylinder compression test.
Is the cylinder compression for all of the cylinders at
or above the value specified?
1250 kPa
(181 psi)
Go to Step 7Go to Step 4
4Inspect the timing belt alignment.
Is the timing belt in alignment?–Go to Step 6Go to Step 5
5Align or replace the timing belt as needed.
Is the repair complete?–Go to Step 2–
6Repair internal engine damage as needed.
Is the repair complete?–Go to Step 2–
7Inspect the fuel pump fuse.
Is the problem found?–Go to Step 8Go to Step 9
8Replace the fuse.
Is the repair complete?–Go to Step 2–
9
Check for the presence of spark from all of the
ignition wires while cranking the engine.
Is spark present from all of the ignition wires?
–
Go to Step 23Go to Step 10
10
1. Measure the resistance of the ignition wires.
2. Replace any of the ignition wire(s) with a
resistance above the value specified.
3. Check for the presence of spark from all of the
ignition wire.
Is spark present from all of the ignition wires?
5 kΩGo to Step 2Go to Step 11
11
1. Turn the ignition OFF.
2. Disconnect the crankshaft position (CKP) sensor
connector.
3. Turn the ignition ON.
4. Measure the voltage between following terminals:

Terminal 1 and 3 of the CKP sensor connector.

Terminal 2 and 3 of the CKP sensor connector.

Terminal 1 of the CKP sensor connector and
ground.

Terminal 2 of the CKP sensor connector and
ground.
Are the voltage measure within the value specified?
≈ 0.4 VGo to Step 13Go to Step 12

ENGINE CONTROLS 1F–303
DAEWOO M-150 BL2
BACKFIRE
Definition: Fuel ignites in the intake manifold, or in the
exhaust system, making a loud popping noise.Important: Before diagnosing the symptom, check ser-
vice bulletins for updates.
StepActionValue(s)YesNo
1
Were the Important Preliminary Checks performed?
–
Go to Step 2
Go to
“Important
Preliminary
Checks”
2
1. Inspect for crossed or crossfiring ignition wires.
2. Check the ignition system output voltage for all
cylinders using a spark tester.
3. Inspect the spark plugs for excessive wear,
burned electrodes, improper gap, or heavy
deposits.
Is the problem found?
–
Go to Step 3Go to Step 4
3
Repair or replace any ignition system components
as needed.
Is the repair complete?
–
System OK
–
4
1. Check the fuel system operation.
2. Check the fuel injectors by performing an injector
diagnosis.
Is the problem found?
–
Go to Step 5Go to Step 6
5
Repair or replace any fuel system components as
needed.
Is the repair complete?
–
System OK
–
6
1. Inspect the Electric Exhaust Gas Recirculation
(EEGR) gasket for a leak or a loose fit.
2. Check the EEGR valve for proper operation.
3. Inspect the intake manifold and the exhaust
manifold for a casting flash.
Is the problem found?
–
Go to Step 7Go to Step 8
7Repair or replace any components as needed.
Is the repair complete?–System OK–
8
1. Inspect the timing belt for proper installation and
tension.
2. Check the engine compression.
3. Inspect the intake manifold gasket and the
exhaust manifold gasket for leaks.
4. Check for sticking or leaking valves.
5. Repair or replace any components as needed.
Are all checks and corrections complete?
–
System OK
–