2003 DAEWOO MATIZ sensor

1D–14 ENGINE COOLING
DAEWOO M-150 BL2
MAA1D020
4. Remove the thermostat.
Remove the bolts.
Remove the thermostat housing.
Remove the thermostat with the gasket.
5. Check the gasket for crack or other damage.
6. Inspect the valve seat for foreign matter that could
prevent the valve from seating properly.
7. Inspect the thermostat for proper operation. Refer to
“Thermostat Test” in this section.
MAA1D011
Installation Procedure
1. Install the thermostat with the bolts and the thermo-
stat housing.
Tighten
Tighten the mounting bolts to 8–15 Nm (71–130
lb-in).
2. Secure the upper radiator hose to the thermostat
housing with a hose clamp.
3. Refill the engine cooling system. Refer to “Draining
and Refilling the Cooling System” in this section.
4. Install the air filter assembly. Refer to Section 1B,
SOHC Engine Mechanical.
D102D515
COOLANT TEMPERATURE SENSOR
Removal Procedure
1. Disconnect the negative battery cable.
2. Disconnect the lower radiator hose and drain the
coolant. Refer to “Draining and Refilling the Cooling
System” in this section.
3. Remove the coolant temperature sensor.
Disconnect the electrical connector (1).
Remove the coolant temperature sensor (2).
D12D516A
10 Nm
Installation Procedure
1. Install the coolant temperature sensor into the
threaded hole in the intake manifold.
Tighten
Tighten the coolant temperature sensor to 10 Nm
(89 lb-in).
Connect the electrical connector to the coolant
temperature sensor (1).
2. Connect the lower radiator hose and refill the coolant.
Refer to “Draining and refilling the cooling system” in
this section.
3. Connect the negative battery cable.

ENGINE COOLING 1D–15
DAEWOO M-150 BL2
D102D517
ENGINE COOLANT TEMPERATURE
SENSOR
Removal Procedure
1. Disconnect the negative battery cable.
2. Disconnect the lower radiator hose and drain the
coolant “Draining and Refilling the Cooling System” in
this section.
3. Remove the engine coolant temperature (ECT) sen-
sor.
Disconnect the electrical connector (1).
Remove the ECT sensor (2).
D12D518A
20 Nm
Installation Procedure
1. Install the ECT sensor.
Tighten
Tighten the ECT sensor to 20 Nm (15 lb-ft).
Connect the electrical connector to the ECT sen-
sor (1).
2. Connect the lower radiator hose and refill the coolant.
Refer to “Draining and Refilling the Cooling System”
in this section.
3. Connect the negative battery cable.
D102B533
COOLANT PUMP
Removal Procedure
1. Disconnect the negative battery cable.
2. Disconnect the lower radiator hose and drain the
coolant. Refer to “Draining and Refilling the Cooling
System” in this section.
3. Remove the timing belt. Refer to Section 1B, Engine
Mechanical.
4. Remove the rear timing belt cover.
Remove the bolts (1).
Remove the rear timing belt cover (2).
D102D519
5. Remove the coolant pump.
Remove the nuts (1).
Remove the bolts (2).
Remove the coolant pump (3).
Remove the gasket.
Notice: Remove the coolant pump as shown figure (a).

ENGINE COOLING 1D–17
DAEWOO M-150 BL2
SPECIFICATIONS
GENERAL SPECIFICATIONS
ApplicationDescriptionUnitStandardLimit
Cooling
SystemCooling Type–Forced Water
Circulation
CoolantCoolant CapacityL/qt3.8/4.00
Thermostat Type–Pellet Type
Temperature(opened initially)°C(°F)82(180)
ThermostatTemperature(perfectly opened)°C(°F)95(203.4)
Temperature(perfectly closed)°C(°F)80(176.4)
Stroke(perfectly opened)mm(in.)8 (0.32)
Cooling Fan Type–Electric
Blade NumberEA6
Cooling Fan Diametermm(inch)300(11.8)
Electric CoolingTemperature At Low Speed ON°C(°F)93(199.8)Fan
Temperature At Low Speed OFF°C(°F)90(194.4)
Temperature At High Speed ON°C(°F)100(212.4)
Temperature At High Speed OFF°C(°F)97(207)
Surge TankOpen Pressure of The Pressure ValvekPa (psi)120–150
(17.4–21.8)
Surge Tank
Open Pressure of The Vacuum ValvekPa (psi)10 (1.5)
Water Pump Type–Centrifugal
Coolant PumpImpeller Diametermm(in.)60(2.36)
Impeller Blade NumberEA7
Radiator Type–Cross–Flow
Core Widthmm(in.)458(18.03)RadiatorCore Heightmm(in.)295(11.61)
Core Depth (Standard/Heavy Duty)mm(in.)16/27(0.63/1.06)
Resistance
(Coolant Temperature 50°C(122.4°F))Ω185.2
Coolant
TemperatureResistance
(Coolant Temperature 85°C(185.4°F))Ω49.2
SensorResistance
(Coolant Temperature 105°C(221.4°F))Ω27.5
Engine CoolantResistance
(Coolant Temperature 20°C(68.4°F))Ω3,520
Temperature
SensorResistance
(Coolant Temperature 80°C(176.4°F))Ω332

1D–18 ENGINE COOLING
DAEWOO M-150 BL2
FASTENER TIGHTENING SPECIFICATIONS
ApplicationNmLb-FtLb-In
Engine Coolant Temperature Sensor10–89
Coolant Temperature Sensor2015–
Coolant Pipe Bolt8 – 15–71 – 130
Electric Cooling Fan Motor Nut3.0 – 3.2–27 – 28
Electric Cooling Fan Assembly Bolt3.5 – 4.5–31 – 40
Distributor Case Bolt/Nut8 – 12–71 – 106
Radiator Mounting Bracket Bolt3.5 – 4.5–31 – 40
Thermostat Housing Bolt8 – 15–71 – 130
Water Inlet Cap Bolt8 – 12–71 – 106
Coolant Pump Bolt/Nut9–12–80 – 106
Coolant Pump Stud Bolt9–12–80 – 106

ENGINE ELECTRICAL 1E–5
DAEWOO M-150 BL2
the sequence of ignition order. It also adjusts the ignition
timing according to the engine condition.
This vehicle uses the distributor (optical sensor type)
which controls the preminary current of the ignition coil
by the ECM.
The ignition timing change is controlled electronically by
the ECM.
When diagnosing the ignition system, refer to Section
1F, Engine Controls.
IGNITION COIL
Ignition coil is a sort of transformer to generate high volt-
age (15,000–25,000V) which can bring spark at the
spark plugs and has an iron cored closed magnetic type.The closed magnetic typed ignition coil is used for the
High Energy Ignition (H.E.I) system. Comparing with the
iron cored open magnetic type, the closed type almost
has no loss of magnetic flux, and smaller in size, so it
produces the high voltage of secondary voltage.
SPARK PLUG
It is a part of ignition secondary current, and it burns the
compressed mixture by sparking the high voltage in-
duced from the ignition coil.

ENGINE ELECTRICAL 1E–9
DAEWOO M-150 BL2
IGNITION SYSTEM
D102E404
1 Ignition Coil
2 Spark Pulg
3 Ignitoin Wire (#0)
4 Ignition Wires (#1, #2, #3)
5 Support Clamp
6 Mounting Clamp
7 Distributor Assembly
8 Coupling
9 Distributor Oil Seal
10 Distributor Housing
11 Distributor Shaft12 Plate
13 Optical Sensor Unit
14 Plate
15 Bushing
16 Disc Wheel
17 Inner Cover
18 Outer Cover
19 Distributor Rotor
20 Distributor Cap Seal
21 Distributor Cap

ENGINE ELECTRICAL 1E–11
DAEWOO M-150 BL2
IGNITION SYSTEM (Cont’d)
ConditionProbable CauseCorrection
Hard to Starting the Engine
Faulty ignition coil.
Replace the ignition coil.

Faulty distributor (include the
optical sensor).
Replace the distributor or the
optical sensor.

Faulty spark plug.
Replace the spark plug or Adjust
the gap.

Poor ignition timing.
Reset the valve timing.
Engine Idling State is Unstable
Faulty spark plug.
Replace the spark plug or Adjust
the gap.

Faulty ignition coil.
Replace the ignition coil.

Poor ignition timing.
Reset the valve timing.
Poor Engine Accelerating
Poor ignition timing.
Reset the valve timing.

1E–14 ENGINE ELECTRICAL
DAEWOO M-150 BL2
REPAIR INSTRUCTIONS
ON–VEHICLE SERVICE
D12E5011
STARTER
Removal Procedure
1. Disconnect the negative battery cable.
2. Disconnect the electrical connector and clip around
the starter.

Remove the engine oil temperature sensor to dis-
connect the harness connector (1).

Remove the starter solenoid nut to disconnect the
electrical cable (2).

Remove the harness clip bolt to disconnect the
harness clip (3).

Remove the ground bolt (4).
D102E502
3. Remove the starter assembly.

Remove the starter mounting bolts (1).

Remove the starter assembly (2).
D12E5031
Installation procedure
1. Install in the reverse order of removal.
2. Install the starter mounting bolts and starter solenoid
nut.
Tighten

Tighten the starter mounting bolts to 55–65 Nm
(41–48 lb-ft) (a).

Tighten the starter solenoid nut to 9–12 Nm
(80–106 lb-in) (b).

Tighten the harness clip bolt to 9–12 Nm (80–106
lb-in) (c).

Tighten the ground bolt to 35–41 Nm (26–30 lb-ft)
(d).