2003 DAEWOO MATIZ length

interior lights fuel consumption trunk spark plugs catalytic converter tow bar

Page 510 of 1184

DAEWOO MATIZ 2003 Service Repair Manual 4A –4 HYDRAULIC BRAKES
DAEWOO M-150 BL2
DIAGNOSITIC INFORMATION AND PROCEDURES
BRAKE SYSTEM TESTING
(Left–Hand Drive Shown, Right–Hand
Drive Similar)
Brakes should be tested on a dry, clean, r

4A –4 HYDRAULIC BRAKES
DAEWOO M-150 BL2
DIAGNOSITIC INFORMATION AND PROCEDURES
BRAKE SYSTEM TESTING
(Left–Hand Drive Shown, Right–Hand
Drive Similar)
Brakes should be tested on a dry, clean, reasonably
smooth and level roadway. A true test of brake perfor-
mance cannot be made if the roadway is wet, greasy, or
covered with loose dirt whereby all tires do not grip the
road equally. Testing will also be adversely affected if the
roadway is crowned so as to throw the weight so roughly
that the wheels tend to bounce.
Test the brakes at different vehicle speeds with both light
and heavy pedal pressure; however, avoid locking the
brakes and sliding the tires. Locked brakes and sliding
tires do not indicate brake efficiency since heavily
braked, but turning, wheels will stop the vehicle in less
distance than locked brakes. More tire-to-road friction is
present with a heavily braked, turning tire than with a
sliding tire.
Because of the high deceleration capability, a firmer
pedal may be felt at higher deceleration levels.
There are three major external conditions that affect
brake performance:
Tires having unequal contact and grip of the road will
cause unequal braking. Tires must be equally in-
flated, and the tread pattern of the right and the left
tires must be approximately equal.
Unequal loading of the vehicle can affect the brake
performance since the most heavily loaded wheels
require more braking power, and thus more braking
effort, than the others.
Misalignment of the wheels, particularly conditions of
excessive camber and caster, will cause the brakes
to pull to one side.
To check for brake fluid leaks, hold constant foot pres-
sure on the pedal with the engine running at idle and the
shift lever in NEUTRAL. If the pedal gradually falls away
with the constant pressure, the hydraulic system may be
leaking. Perform a visual check to confirm any sus-
pected leaks.
Check the master cylinder fluid level. While a slight drop
in the reservoir level results from normal lining wear, an
abnormally low level indicates a leak in the system. The
hydraulic system may be leaking either internally or ex-
ternally. Refer to the procedure below to check the mas-
ter cylinder. Also, the system may appear to pass this
test while still having a slight leak. If the fluid level is nor-
mal, check the vacuum booster pushrod length. If an in-
correct pushrod length is found, adjust or replace the
rod.Check the master cylinder using the following proce-
dure:
Check for a cracked master cylinder casting or brake
fluid leaking around the master cylinder. Leaks are in-
dicated only if there is at least one drop of fluid. A
damp condition is not abnormal.
Check for a binding pedal linkage and for an incorrect
pushrod length. If both of these parts are in satisfac-
tory condition, disassemble the master cylinder and
check for an elongated or swollen primary cylinder or
piston seals. If swollen seals are found, substandard
or contaminated brake fluid should be suspected. If
contaminated brake fluid is found, all the components
should be disassembled and cleaned, and all the rub-
ber components should be replaced. All of the pipes
must also be flushed.
Improper brake fluid, or mineral oil or water in the fluid,
may cause the brake fluid to boil or cause deterioration
of the rubber components. If the primary piston cups in
the master cylinder are swollen, then the rubber parts
have deteriorated. This deterioration may also be evi-
denced by swollen wheel cylinder piston seals on the
drum brake wheels.
If rubber deterioration is evident, disassemble all the hy-
draulic parts and wash the parts with alcohol. Dry these
parts with compressed air before reassembly to keep al-
cohol out of the system. Replace all the rubber parts in
the system, including the hoses. Also, when working on
the brake mechanisms, check for fluid on the linings. If
excessive fluid is found, replace the linings.
If the master cylinder piston seals are in satisfactory
condition, check for leaks or excessive heat conditions.
If these conditions are not found, drain the fluid, flush the
master cylinder with brake fluid, refill the master cylin-
der, and bleed the system. Refer to “Manual Bleeding
the Brakes” in this section.
BRAKE HOSE INSPECTION
The hydraulic brake hoses should be inspected at least
twice a year. The brake hose assembly should be
checked for road hazard damage, cracks, chafing of the
outer cover, and for leaks or blisters. Inspect the hoses
for proper routing and mounting. A brake hose that rubs
on a suspension component will wear and eventually
fail. A light and a mirror may be needed for an adequate
inspection. If any of the above conditions are observed
on the brake hose, adjust or replace the hose as neces-
sary.

Page 511 of 1184

DAEWOO MATIZ 2003 Service Repair Manual HYDRAULIC BRAKES 4A–5
DAEWOO M-150 BL2
WARNING LAMP OPERATION
This brake system uses a BRAKE warning lamp located
in the instrument panel cluster. When the ignition switch
is in the III position, t

Page 512 of 1184

DAEWOO MATIZ 2003 Service Repair Manual 4A –6 HYDRAULIC BRAKES
DAEWOO M-150 BL2
MANUAL BLEEDING THE BRAKES
Important: The bleeding sequence is as follows; right
rear, left rear, right front, and left front.
Important: Check the fluid lev

Page 644 of 1184

DAEWOO MATIZ 2003 Service Repair Manual FIVE-SPEED MANUAL TRANSAXLE 5B–19
DAEWOO M-150 BL2
D13B530A
3. Install the gear shift control case and the select lever.
Tighten
Tighten the gear shift control case bolts to 18–28
Nm (13–21 l

Page 682 of 1184

DAEWOO MATIZ 2003 Service Repair Manual 5C – 2 CLUTCH
DAEWOO M-150 BL2
DESCRIPTION AND OPERATION
DRIVING MEMBERS
The driving members consist of two flat surfaces ma-
chined to a smooth finish. One of these is the rear face
of the engine

Page 817 of 1184

DAEWOO MATIZ 2003 Service Repair Manual 8A –2 SEAT BELTS
DAEWOO M-150 BL2
DESCRIPTION AND OPERATION
DRIVER SEAT BELT WARNING
The driver’s safety belt incorporates a safety belt re-
minder light in the instrument cluster to remind the d

8A –2 SEAT BELTS
DAEWOO M-150 BL2
DESCRIPTION AND OPERATION
DRIVER SEAT BELT WARNING
The driver’s safety belt incorporates a safety belt re-
minder light in the instrument cluster to remind the driver
if the safety belt is not fastened when the ignition is
turned ON.
THREE-POINT PRETENSIONER
FRONT SEAT BELT (W/EUROPE
ONLY)
The pretensioner front seat belt is optional. It contains a
electrically-controlled pyrotechnical retractor, which re-
duces seat belt slack when it is activated in a head-on or
angled front collision. The pretensioner front seat belt
must be replaced after an accident that causes its ac-
tivation.
THREE-POINT WLR FRONT SEAT
BELT
The three-point web locking retractor (WLR) seat belt
will limit the movement of the driver and offer better
protection in an accident.
THREE-POINT ELR FRONT SEAT
BELT
The three-point emergency locking retractor (ELR) front
seat belt is always unlocked, allowing the passenger
freedom of movement, except in emergencies (rapid de-
celeration, rapid acceleration, or hard cornering maneu-
vers).
THREE-POINT ELR REAR
OUTBOARD SEAT BELT
The rear outboard seating positions use the three-point
emergency locking retractor (ELR) seat belts. The
three-point emergency locking retractor (ELR) seat beltis always unlocked, allowing the passenger freedom of
movement, except in emergencies (rapid deceleration,
rapid acceleration, or hard cornering maneuvers).
TWO-POINT LAP REAR CENTER
SEAT BELT
The two-point lap rear center seat belt is a single contin-
uous length of webbing. The webbing is routed from the
anchor through a latch plate and into a single retractor.
OPERATIONAL AND FUNCTIONAL
CHECKS
Caution:
Keep sharp objects and potentially damaging ob-
jects away from the seat belts.
Avoid bending or damaging any portion of the
buckle or the latch plate.
Do not bleach or dye the belt webbing. Use only
mild soap and water in order to clean the belts.
When installing the seat belt anchor bolts and
the screws, start the bolts and the screws by
hand in order to prevent crossthreading.
Do not attempt any repairs on the retractor mech-
anisms or the covers. Replace any defective as-
semblies with new assemblies.
Replace any belts that are cut or damaged in any
way.
1. Inspect all seat belt anchor bolts and the screws in or-
der to verify that they are secure.
2. Inspect the seat belt buckle. The buckle must lock
and unlock easily.
3. After inserting the latch into the buckle, tug sharply on
the belt. The buckle must remain locked.
4. Fully extend the shoulder belt portion to make sure
that there is no twisting or tears in the belt.
5. Let the shoulder belt retract fully. The belt should re-
tract easily.

Page 1154 of 1184

DAEWOO MATIZ 2003 Service Repair Manual 9T–2 REMOTE KEYLESS ENTRY AND ANTI-THEFT SYSTEM
DAEWOO M-150 BL2
DESCRIPTION AND OPERATION
REMOTE KEYLESS ENTRY AND
ANTI-THEFT SYSTEM
The remote keyless entry and anti-theft system can per-
form th

9T–2 REMOTE KEYLESS ENTRY AND ANTI-THEFT SYSTEM
DAEWOO M-150 BL2
DESCRIPTION AND OPERATION
REMOTE KEYLESS ENTRY AND
ANTI-THEFT SYSTEM
The remote keyless entry and anti-theft system can per-
form the following functions:
Remotely lock and unlock the vehicle doors with a
hand-held high-frequency transmitter.
Sense intrusion into the vehicle through the doors,
the tailgate, or the hood.
Activate a warning to signal an intrusion.
Help the driver find the vehicle in a parking area.
Automatically re-lock the doors if a door or the trunk is
not opened within 30 seconds after the vehicle has
been unlocked by the remote keyless entry.
Communicate serial data to a scan tool to help diag-
nose system faults.
The remote keyless entry and anti-theft system consists
of the following components:
Keyless entry and anti-theft control module/receiver.
Security indicator.
Tailgate open switch.
Door open switches.
Central locking unit.
Flashing turn signal lamps.
Siren.
Hood open switch.
REMOTE LOCKING AND UNLOCKING
The hand-held transmitter locks and unlocks the vehicle
doors by sending radio waves to the control module/re-
ceiver in the vehicle. The effective range of the transmit-
ter varies between 5 and 10 meters (approximately 16 to
32 feet), depending on whether or not objects such as
other vehicles are blocking the path of the radio waves.
The transmitter has a LOCK button and an UNLOCK
button which only function when the ignition is OFF.
Pressing the UNLOCK button has the following effects:
The doors are unlocked.
The turn signal lamps flash twice.
The control module is disarmed.
Pressing the LOCK button has the following effects:
The doors are locked.
The turn signal lamps flash once.
The control module is armed.
The transmitter has a replaceable battery. The battery is
designed to last at least two years before replacement is
necessary.
SECURITY INDICATOR
There is a security indicator on the instrument panel. Af-
ter the LOCK button of the transmitter is pressed, the
module is placed in the armed mode, and the security
indicator flashes. The security indicator turns ON for 1/8
second and OFF for 7/8 second. It then flashes at that
frequency until the control module/receiver is disarmed.
INTRUSION SENSING
The anti-theft function is armed if the transmitter sends
the LOCK message to the control module/receiver when
the ignition is OFF.
When the hood, the door, or the tailgate is opened, the
hood open switch, the door open switch, or the tailgate
open switch will change its input to ground. The alarm
will be activated if the hood open sensor, the door open
sensor, or the tailgate open sensor changes its input to
ground before either of the following conditions occurs:
An UNLOCK message is received from the transmit-
ter.
SIREN
The remote keyless entry system is armed when the
LOCK message is received from the transmitter when
the ignition is OFF. When the system is armed, it will ac-
tivate the siren and flash the turn signals for 28 seconds
if any of the following conditions occurs:
A door is opened (front door open switch input is
changed to ground).
The tailgate is opened (tailgate open switch input is
changed to ground).
The hood is opened while the anti-theft system is
armed (hood open switch input is changed to
ground).
The siren is disarmed when any of the following condi-
tions occurs:
The ignition switch is turned ON with the key.
The UNLOCK button or the LOCK button on the re-
mote transmitter is pressed.
VEHICLE LOCATOR
The remote keyless entry system assists the driver in lo-
cating the vehicle. When the vehicle is unlocked with the
remote control, the turn signals flash twice to indicate
the location of the vehicle. The duration of the flashes
and the length of time between flashes is used to indi-
cate certain vehicle conditions. Refer to “Fault or Alarm
Indication” in this section.

Page 1162 of 1184

DAEWOO MATIZ 2003 Service Repair Manual 9T–10 IMMOBILIZER ANTI-THEFT SYSTEM
DAEWOO M–150 BL2
DESCRIPTION AND OPERATION
IMMOBILIZER SYSTEM
The purpose of the Immobilizer system is to provide
additional theft deterrence to the vehicle in

9T–10 IMMOBILIZER ANTI-THEFT SYSTEM
DAEWOO M–150 BL2
DESCRIPTION AND OPERATION
IMMOBILIZER SYSTEM
The purpose of the Immobilizer system is to provide
additional theft deterrence to the vehicle in which it is
installed and to prevent it from being stolen or driven by
unauthorized users.
The verification of the user authorization is done by an
ignition key with integrated transponder.
The external LED displays the Immobilizer status and
has an additional theft deterrence function.
To secure the communication, the status is exchanged
between the Immobilizer and the ECM in a 5 byte of en-
coded data.
These 5 bytes are composed by a mixture of random
data and two types of fixed code
a vehicle model identification number : MIN
a vehicle specific identification : VIN
The MIN is known from the first supply of the system.
The VIN is realized by ICU on the special order from the
key coding (reading of transponder code and storing it
as valid key code in Immobilizer EEPROM).
A different random data is computed at each key transi-
tion.
All the immobilization communication between the ECM
and ICU is made on K-line (K line : Serial data line ’7’).
Due to the learning of the Vehicle specific identification
Number, both ICU and ECM can stay in 3 stable modes
Virgin mode (VIN not learnt)
Learnt mode (VIN learnt)
Neutral mode (for a new VIN learning)
In case of using valid key, the release message commu-
nication with the ECM take place and the LED displays
the Immobilizer status valid key In case of using invalid
key, the ECM disables the fuel injector circuit with coded
intervention and sets DTC(Diagnostic Trouble Code)
The above conditions are maintained until the ignition is
switched off.
An ECM without an immobilizer control unit cannot be
interchanged for an ECM that is used with an immobiliz-
er control unit system. The Immobilizer control unit and
ECM must have a matching ID code. ID coding and key
coding are accomplished by using Scanner–100
The Immobilizer system consists of
a maximum or 5 ignition keys with integrated trans-
ponder
the toroidal coil (Detection coil) for energizing and
reading the transponder mounted at the ignition lock.
the Immobilizer control unit(ICU) with :
– power supply
– ignition input circuit
– transponder modulation and demodulation unit – EEPROM
– driver electronic for the external status LED
– serial data link hardware
the external status LED for displaying the Immobilizer
status
the serial data link between Immobilizer and ECM
ELECTRONICALLY CODED KEYS
Each valid ignition key has an internal transponder
which is a read /write transponder.
The transponder contains an implementation of a cryp-
to-algorithm with 96 bits of user configurable s cret-key
contained in EEPROM and transmits data to the ICU by
modulating the amplitude of the ele tromagnetic field,
and receives data and commands in a similar way.
DETECTION COIL
The toroidal coil is mounted at the ignition lock in front of
the key barrel.
It is connected to the ICU with a four terminal connector
fixed at the body of the coil.
The length of the connection between coil and Immobi-
lizer is restricted to 50cm. The correct placement on the
ignition lock and the exact electrical data is very impor-
tant for the reading distance of transponder.
The toroidal coil and receiving coil inside the transpond-
er built a transformer. During the readingprocess the coil
induces energy into the transponder. The transponder
charges the field and generates an amplitude modulated
signal with the manchester coded data. This charge of
the field is demodulated inside the Immobilizer.
The Immobilizer contains the coil driver hardware for di-
rect connection of the toroidal coil.
IMMOBILIZER CONTROL UNIT
The function of the Immobilizer System is shared be-
tween the ICU and the ECM.
The task of the Immobilizer Electronic Control unit (ICU)
are:
Reading of the input information “ignition ON/OFF”
Controlling the states LED
Controlling the transponder read/write process (mod-
ulation, demodulation, decoding, comparison of the
read code with the code of the valid keys).
Communication with the ECM after ignition ON (re-
ceiving of the ECM-request and transmission of re-
lease message).
Special functions for calculation and handling of the
VIN-code.

Page: < prev 1-8 9-16

OBD port change time service reset check transmission fluid seat memory turn signal