2003 DAEWOO MATIZ glove box

8B–72 SUPPLEMENTAL INFLATABLE RESTRAINTS (SIR)
DAEWOO M-150 BL2
D1AB508A
3. Connect the passenger airbag module connector.
4. Install the glove box. Refer to Section 9E, Instrument/
Driver Information.
5. Connect the negative battery cable.
D19E573A
SENSING AND DIAGNOSTIC
MODULE (SDM)
Tool Required
DS 401 Torx Bolt Wrench.
Removal Procedure
1. Disconnect the negative battery cable.
2. Remove the floor console. Refer to Section 9G, Inte-
rior Trim.
D110B511
3. Remove the SDM.

Disconnect the SDM electrical connector (1).

Remove the torx bolts using a torx bolt wrench DS
401 (2).

Remove the SDM (3).
D1AB512A
Installation Procedure
Notice: Do not install an SDM that has been dropped or
has water damage, dents, cracks, or other visible de-
fects. Attempted use of a defective SDM can result in
vehicle damage.
1. Install the SDM with the mounting torx bolts so that
the arrow on the SDM label points toward the front of
the vehicle.
Notice : Ground the wiring harness to the mounting torx
bolt (1).
Tighten
Tighten the SDM mounting torx bolts to 15 Nm (11
lb-ft).
2. Connect the SDM electrical connector.

DAEWOO M-150 BL2
SECTION 9E
INSTRUMENTATION/DRIVER INFORMATION
CAUTION: Disconnect the negative battery cable before removing or installing any electrical unit or when a
tool or equipment could easily come in contact with exposed electrical terminals. Disconnecting this cable
will help prevent personal injury and damage to the vehicle. The ignition must also be in B unless otherwise
noted.
TABLE OF CONTENTS
Description and Operation 9E-2. . . . . . . . . . . . . . . . . .
Cigar Lighter 9E-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ashtray 9E-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Instrument Panel Vents 9E-2. . . . . . . . . . . . . . . . . . . .
Glove Box 9E-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Digital Clock 9E-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Instrument Cluster 9E-2. . . . . . . . . . . . . . . . . . . . . . . .
Speedometer/Odometer/Trip Odometer 9E-2. . . . . .
Fuel Gauge 9E-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Temperature Gauge 9E-2. . . . . . . . . . . . . . . . . . . . . . .
Instrument Cluster Indicator Lamps 9E-2. . . . . . . . . .
Component Locator 9E-3. . . . . . . . . . . . . . . . . . . . . . . .
Instrument Panel Assembly 9E-3. . . . . . . . . . . . . . . . .
Instrument Cluster 9E-4. . . . . . . . . . . . . . . . . . . . . . . . .
Diagnostic Information and Procedures 9E-5. . . . .
Cigar Lighter 9E-5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HVAC Panel Illumination 9E-6. . . . . . . . . . . . . . . . . . .
Digital Clock 9E-7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Repair Instructions 9E-8. . . . . . . . . . . . . . . . . . . . . . . . .
On-Vehicle Service 9E-8. . . . . . . . . . . . . . . . . . . . . . . . . .
Cigar Lighter 9E-8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ashtray 9E-9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Instrument Cluster Trim Panel Vents 9E-9. . . . . . . . .
Digital Clock 9E-10. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Glove Box 9E-11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Instrument Cluster 9E-11. . . . . . . . . . . . . . . . . . . . . . . .
Instrument Panel 9E-12. . . . . . . . . . . . . . . . . . . . . . . . .
Tie–Bar 9E-14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Instrument Cluster Trim Panel 9E-16. . . . . . . . . . . . . .
Instrument Trim Panel Assembly 9E-16. . . . . . . . . . .
Instrument Cluster Indicator Lamps 9E-19. . . . . . . . .
Speedometer/Odometer/Trip Odometer 9E-19. . . . .
Fuel Gauge/Temperature Gauge 9E-20. . . . . . . . . . .
Specifications 9E-22. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fastener Tightening Specifications 9E-22. . . . . . . . . .
Instrument Cluster Indicator Lamps
Specifications 9E-22. . . . . . . . . . . . . . . . . . . . . . . . . .
Schematic and Routing Diagrams 9E-23. . . . . . . . . .
Instrument Cluster 9E-23. . . . . . . . . . . . . . . . . . . . . . . .
Instrument Panel Illumination 9E-25. . . . . . . . . . . . . .
Digital Clock 9E-26. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

9E–2 INSTRUMENTATION/DRIVER INFORMATION
DAEWOO M-150 BL2
DESCRIPTION AND OPERATION
CIGAR LIGHTER
The cigar lighter is located in the front portion of the in-
strument panel. To use the lighter, push it in completely.
When the lighter is hot, it will release itself from contact
with the heating element. The lighter and the heating
element can be damaged if the lighter is not allowed to
release itself fully from the heating element. Cigar lighter
is not equipped with the lamp.
ASHTRAY
The ashtray is located in the lower portion of the instru-
ment panel. In case of cleaning the ashtray up, remove
the ashtray by pushing the upper button and clean it up.
The ashtray lamp is optional.
INSTRUMENT PANEL VENTS
The center and the side vents in the instrument panel
can be adjusted up and down and from side to side. The
side vents can also be aimed toward the side windows in
order to defog them.
GLOVE BOX
The glove box can be opened by pulling up on the latch
handle. The glove box must be removed in order to gain
access to the passenger-side airbag module.
DIGITAL CLOCK
The digital clock is located in the instrument panel, be-
low the defroster grille. The clock is capable of a 12 –
hour display.
INSTRUMENT CLUSTER
The instrument cluster is located above the steering col-
umn and in the instrument cluster trim panel. The instru-
ment cluster contains the instruments that provide the
driver with vehicle performance information. The instru-
ment cluster contains a speedometer, an odometer, a
trip odometer, a temperature gauge, a fuel gauge, and
several indicator lamps. For replacement of the indicator
lamp bulbs contained in the instrument cluster, refer to
“Instrument Cluster Indicator Lamps Specifications” in
this section.
SPEEDOMETER/ODOMETER/TRIP
ODOMETER
The speedometer measures the speed of the vehicle. It
consists of an instrument cluster gauge connected to
the vehicle speed sensor on the transaxle output shaft.
The odometer measures the total distance the vehicle
has traveled since it was manufactured. It consists of an
instrument cluster gauge connected to the vehicle
speed sensor on the transaxle output shaft.
The trip odometer measures the distance the vehicle
has traveled since the odometer was last reset. It con-
sists of an instrument cluster gauge connected to the
vehicle speed sensor on the transaxle output shaft. The
trip odometer can be reset to zero at any time so that the
driver can record the distance traveled from any starting
point.
FUEL GAUGE
The fuel gauge consists of an instrument cluster gauge
connected to a sending unit in the fuel tank.
The fuel gauge indicates the quantity of fuel in the tank
without the ignition switch position.
TEMPERATURE GAUGE
The temperature gauge consists of an instrument clus-
ter gauge connected to a temperature sensor that is in
contact with the circulating engine coolant.
The temperature gauge indicates the temperature of the
coolant. Prolonged driving or idling in very hot weather
may cause the pointer to move beyond the center of the
gauge. The engine is overheating if the pointer moves
into the red zone at the upper limit of the gauge.
INSTRUMENT CLUSTER INDICATOR
LAMPS
The instrument cluster contains indicator lamps that in-
dicate the functioning of certain systems or the exis-
tence of potential problems with the operation of the
vehicle. The indicator lamps are replaceable. For re-
placement of the indicator lamps contained in the instru-
ment cluster, refer to “Instrument Cluster Indicator
Lamps Specifications” in this section.

INSTRUMENTATION/DRIVER INFORMATION 9E–3
DAEWOO M-150 BL2
COMPONENT LOCATOR
INSTRUMENT PANEL ASSEMBLY
(Left–Hand Drive Shown, Right–Hand Drive Similar)
D19B401A
1. Tie–Bar
2. Tie–Bar Center
3. Instrument Panel Guide
4. Defroster Grille
5. Instrument Panel Upper Cap
6. Passenger’s Airbag Blank Cover
7. Demister Grille
8. Side Ventilation Grille
9. Glove Box Bracket
10. Glove Box11. Instrument Cluster Housing Molding
12. Center Ventilation Grille
13. Switch Blank Cover (Fog Lamp Switch)
14. Hazard Warning Switch
15. Immobilizer LED Indicator Switch
16. Ashtray Bracket
17. Ashtray
18. Ashtray Lamp
19. Cigar Lighter Housing
20. Instrument Cluster Bracket
21. Instrument Panel

INSTRUMENTATION/DRIVER INFORMATION 9E–11
DAEWOO M-150 BL2
D109B509
GLOVE BOX
(Left–Hand Drive Shown, Right–Hand
Drive Similar)
Removal Procedure
1. Remove the hinge pins at the base of the glove box.
D109B510
2. Remove the glove box from the instrument panel.
D109B509
Installation Procedure
1. Install the glove box to the instrument panel with the
hinge pins.
D19B514A
INSTRUMENT CLUSTER
Removal Procedure
1. Disconnect the negative battery cable.
2. Remove the instrument cluster trim panel from the in-
strument panel. Refer to “Instrument Cluster Trim
Panel” in this section.
3. Remove the instrument cluster assembly from the in-
strument panel.

Remove the screws (1).

Disconnect the electrical connector and the
speedometer cable (2).

Remove the instrument cluster (3).

9E–12 INSTRUMENTATION/DRIVER INFORMATION
DAEWOO M-150 BL2
D19B515A
Installation Procedure
1. Connect the electrical connector and the speedom-
eter cable.
2. Install the instrument cluster assembly to instrument
panel with screws.
3. Install the instrument cluster trim panel to the instru-
ment panel. Refer to “Instrument Cluster Trim Pan-
el” in this section.
4. Connect the negative battery cable.
D109B516
INSTRUMENT PANEL
(Left–Hand Drive Shown, Right–Hand
Drive Similar)
Removal Procedure
1. Disconnect the negative battery cable.
2. Remove the driver’s airbag module from the steer-
ing wheel. Refer to Section 8B, Supplemental Inflat-
able Restraints (SIR) (For the vehicle equipped with
the airbag).
3. Remove the steering wheel from the steering col-
umn. Refer to Section 6E, Steering Wheel and Col-
umn.
4. Remove the steering column trim cover. Refer to
Section 6E, Steering Wheel and Column.
5. Remove the signal lamp switch and the wiper
switch. Refer to Section 6E, Steering Wheel and
Column.
6. Pry off the A–pillar trim panels. Refer to Section 9G,
Interior Trim.
7. Remove the instrument cluster trim panel from the
instrument panel.

Remove the screws (1)

Using a flathead screwdriver, remove the instru-
ment cluster trim panel (2).
Notice: To prevent the instrument panel damage, cover
the flathead screwdriver with a soft cloth.
D109B517
8. Remove the hood latch release lever from the in-
strument panel. Refer to Section 9R, Body Front
End.
9. Remove the glove box assembly from the instru-
ment panel. Refer to “Glove Box” in this section.
10. Remove the passenger’s airbag module from the in-
strument panel. Refer to Section 8B, Supplemental
Inflatable Restraints (SIR) (For vehicle equipped
with the airbag).
11. Put aside the floor console after removing the
screws (1).

9E–14 INSTRUMENTATION/DRIVER INFORMATION
DAEWOO M-150 BL2
7. Install the instrument cluster assembly. Refer to “In-
strument Cluster” in this section.
8. Install the floor console with the screws.
9. Install the passenger’s airbag module to the instru-
ment panel. Refer to Section 8B, Supplemental In-
flatable Restraints (SIR) (For vehicle equipped with
the airbag).
10. Install the glove box assembly to the instrument
panel. Refer to “Glove Box” in this section.
11. Install the hood latch release lever to the instrument
panel. Refer to Section 9R, Body Front End.
12. Install the instrument cluster trim panel to the instru-
ment cluster trim panel with the screws.
13. Install the A–pillar trim panels. Refer to Section 9G,
Interior Trim.
14. Install the signal lamp switch and the wiper switch.
Refer to Section 6E, Steering Wheel and Column.
15. Install the steering column trim cover. Refer to Sec-
tion 6E, Steering Wheel and Column.
16. Install the steering wheel to the steering column.
17. Install the driver’s airbag module to the steering
wheel. Refer to Section 8B, Supplemental Inflatable
Restraints (SIR) (For vehicle equipped with the air-
bag).
18. Connect the negative battery cable.
D109B522
TIE–BAR
(Left–Hand Drive Shown, Right–Hand
Drive Similar)
Removal Procedure
1. Disconnect the negative battery cable.
2. Remove the instrument panel assembly. Refer to “In-
strument Panel” in this section.
3. Remove the defroster duct hose from the tie–bar.

Remove the screws (1).

Remove the defroster duct hose (2).
D19B547A
4. Remove the nuts and the steering column. Refer to
Section 6E, Steering Wheel and Column.
5. Disconnect the electrical connectors and electrical
wiring harness after removing the electrical wiring
harness strips.

Remove the electrical wiring harness strip.

Disconnect the brake switch connector (1).

Disconnect the thermostat connector (2).

Disconnect the blow motor connector (3).

Disconnect the blow motor resistance connector
(4).

Disconnect the electrical wiring harness (5).

9E –18 INSTRUMENT/DRIVER INFORMATION
DAEWOO M-150 BL2
D109B706
8. Remove the glove box striker and bracket from the
instrument panel.

Remove the screws (1).

Remove the glove box striker and bracket (2).
D109B707
9. Remove the instrument panel guide from the instru-
ment panel.

Remove the screws (1).

Remove the instrument panel guide (2).
D109B708
10. Remove the defroster grilles and the demister grilles
from the instrument panel.
a. Defroster grille.
b. Demister grille.
D109B521
Installation Procedure
1. Install the defroster grilles and the demister grilles to
the instrument.
2. Install the instrument panel guide to the instrument
panel with the screws.
3. Install the glove box striker and the bracket to the in-
strument panel with the screws.
4. Install the cigar lighter housing to the instrument pan-
el with the screws.
5. Install the ventilation grilles to the instrument panel
with the screws.
6. Install the ventilation duct to the instrument panel with
the screws.