2003 DAEWOO MATIZ brake

9B – 2 LIGHTING SYSTEMS
DAEWOO M-150 BL2
DESCRIPTION AND OPERATION
HEADLAMPS AND PARKING LAMPS
The headlamps are controlled by the multifunction lever
located on the left side of the steering column. They will
come on with the ignition switch in any position. Turning
the headlamp switch to the first position turns on the
parking lamps, the license plate lamps and the instru-
ment panel illumination. Turning the switch to the sec-
ond position turns on all of the previous lamps and the
headlamps. Turning the switch to the off position turns
off all the lamps.
The parking lamps can be turned on by turning the light-
ing switch to the first position. The parking lamps can be
turned off by turning the switch to the OFF position.
Headlamp high beam and low beam are also controlled
by this lever. When the headlamps are on, pushing the
lever away from the driver until the switch clicks
changes the lamp from low beam to high beam. An indi-
cator lamp on the instrument cluster assembly will come
on when the high beam headlamps are on. To return the
headlamps to low beam, pull the lever toward the driver.
The headlamps must be aimed for proper illumination of
the road. Headlamp aim should be checked whenever a
new headlamp assembly is installed or service repairs to
the front end area may have disturbed the headlamp as-
sembly or its mountings.
FRONT TURN SIGNAL LAMPS
When the turn signals are activated, the side turn signal
lamps flash to signal a turn. The turn signal works only
when the ignition switch is on.
The turn signals are controlled by the light switch on the
left side of the steering column. Moving the lever all the
way up or down (past the detent) will turn on the turn sig-
nals. When the turn is completed, the lever will return to
horizontal and the turn signals will stop flashing.
For changing lanes or shallow turns where the steering
wheel does not turn far enough to cancel the signal,
move the signal only to the first detent and hold it there.
When the lever is released, it will return to horizontal and
the turn signal will cancel.
REAR FOG LAMP
The rear fog lamp is incorporated in the drive side tail-
lamp assembly and are controlled by the rear fog lamp
switch on the instrument panel. The rear fog lamp can
be turned on only when headlamps are on.
TAILLAMPS
The taillamps, stoplamps, backup lamp(s), rear fog lamp
(if equipped with) and turn signal lamps are one assem-
bly.
Turning on either the headlamps or the parking lamps
will also turn on the taillamps. When the brake pedal is
pushed, the taillamps will glow brighter to serve as sto-
plamps.
The center high-mounted stoplamp is located in the rear
window and will come on when the brake pedal is
pressed.
LICENSE PLATE LAMPS
The license plate lamps will come on when the head-
lamps or the parking lamps are on. The license plate
lamps are mounted on the rear bumper, above the li-
cense plate.
INTERIOR COURTESY LAMP
The courtesy lamp is located on the headliner just be-
fore the front seats. The lamp switch has three posi-
tions. If the switch is in the center position, the lamp will
go on whenever a door is opened and go off when it is
closed. In the ON position, the lamp will stay on until it is
turned off. In the OFF position, the lamp will not come
on, even when a door is opened.
BACKUP LAMP(S)
The backup lamps are located in the rear combination
lamps. They will come on when the transaxle is shifted
into REVERSE. On a vehicle with a manual transaxle,
they are activated by a reverse switch which is part of
the transaxle.
DAYTIME RUNNING LAMPS (DRL)
(W/Europe Only)
The daytime running lamps (DRL) work in conjunction
with the exterior lamps system. When the ignition switch
is turned to the ”II” position with the light switch off, park-
ing, tail, license plate and instrument panel lights illumi-
nate. And, when the engine is started, the headlamps
(low beam) also come on.
They remain on until the ignition switch is turned off or
the light switch is turned on. They revert to normal op-
eration when the light switch is on.
The daytime running lamps (DRL) is optional.

9E–14 INSTRUMENTATION/DRIVER INFORMATION
DAEWOO M-150 BL2
7. Install the instrument cluster assembly. Refer to “In-
strument Cluster” in this section.
8. Install the floor console with the screws.
9. Install the passenger’s airbag module to the instru-
ment panel. Refer to Section 8B, Supplemental In-
flatable Restraints (SIR) (For vehicle equipped with
the airbag).
10. Install the glove box assembly to the instrument
panel. Refer to “Glove Box” in this section.
11. Install the hood latch release lever to the instrument
panel. Refer to Section 9R, Body Front End.
12. Install the instrument cluster trim panel to the instru-
ment cluster trim panel with the screws.
13. Install the A–pillar trim panels. Refer to Section 9G,
Interior Trim.
14. Install the signal lamp switch and the wiper switch.
Refer to Section 6E, Steering Wheel and Column.
15. Install the steering column trim cover. Refer to Sec-
tion 6E, Steering Wheel and Column.
16. Install the steering wheel to the steering column.
17. Install the driver’s airbag module to the steering
wheel. Refer to Section 8B, Supplemental Inflatable
Restraints (SIR) (For vehicle equipped with the air-
bag).
18. Connect the negative battery cable.
D109B522
TIE–BAR
(Left–Hand Drive Shown, Right–Hand
Drive Similar)
Removal Procedure
1. Disconnect the negative battery cable.
2. Remove the instrument panel assembly. Refer to “In-
strument Panel” in this section.
3. Remove the defroster duct hose from the tie–bar.

Remove the screws (1).

Remove the defroster duct hose (2).
D19B547A
4. Remove the nuts and the steering column. Refer to
Section 6E, Steering Wheel and Column.
5. Disconnect the electrical connectors and electrical
wiring harness after removing the electrical wiring
harness strips.

Remove the electrical wiring harness strip.

Disconnect the brake switch connector (1).

Disconnect the thermostat connector (2).

Disconnect the blow motor connector (3).

Disconnect the blow motor resistance connector
(4).

Disconnect the electrical wiring harness (5).

9E –16 INSTRUMENT/DRIVER INFORMATION
DAEWOO M-150 BL2
4. Connect the electrical wiring harness.
5. Connect the blow motor resistance connector.
6. Connect the blow motor connector.
7. Connect the thermostat connector.
8. Connect the brake switch connector.
9. Bind the electrical wiring harness strip.
10. Install the steering column with the nuts.
11. Install the defroster duct hose with the screws.
12. Install the instrument panel assembly. Refer to “In-
strument Panel” in this section.
13. Connect the negative battery cable.
D109B516
INSTRUMENT CLUSTER TRIM PANEL
(Left–Hand Drive Shown, Right–Hand
Drive Similar)
Removal Procedure
1. Remove the instrument cluster trim panel from the in-
strument panel.

Remove the screws (1).

Using a flathead screwdriver, remove the central
console cover (2).
Notice: To prevent the instrument panel damage, cover
the flathead screwdriver with a soft cloth.
D109B527
Installation Procedure
1. Install the instrument cluster trim panel with the
screws.
D109B701
INSTRUMENT TRIM PANEL
ASSEMBLY
(Left–Hand Drive Shown, Right–Hand
Drive Similar)
Removal Procedure
1. Disconnect the negative battery cable.
2. Remove the instrument panel assembly. Refer to “In-
strument Panel” in this section.
3. Remove the instrument cluster brackets from the in-
strument panel.

Remove the screws.

Remove the instrument cluster brackets (1).

9E –22 INSTRUMENT/DRIVER INFORMATION
DAEWOO M-150 BL2
SPECIFICATIONS
FASTENER TIGHTENING SPECIFICATIONS

Application

Nm

Lb-Ft

Lb-In
Passenger’s Airbag Module Blank Cover Screw

1.5–2

–

13–18
INSTRUMENT CLUSTER INDICATOR LAMPS SPECIFICATIONS
Indicator Lamp Color Bulb
ABS Warning Amber 14 v 1.4 W
Airbag Warning Red 14 v 1.4 W
Battery Charge Indicator Red 14 v 1.4 W
Fasten Seat Belt Warning Red 14 v 1.4 W
High Beam Indicator Blue 14 v 1.4 W
Low Fuel Level Warning Amber 12 v 3 W Oil Pressure Warning Red 14 v 1.4 W Parking Brake Indicator and Brake Fluid Warning Red 14 v 1.4 W Service Engine Soon Warning Amber 14 v 1.4 W
Turn Signal Indicators

Green

14 v 1.4 W
Instrument Cluster IlluminationBlue12 v 3 W
Rear Fog Lamp IndicatorAmber14 v 1.4 W

DAEWOO M-150 BL2
SECTION 9G
INTERIOR TRIM
CAUTION: Disconnect the negative battery cable before removing or installing any electrical unit or when a
tool or equipment could easily come in contact with exposed electrical terminals. Disconnecting this cable
will help prevent personal injury and damage to the vehicle. The ignition must also be in B unless otherwise
noted.
TABLE OF CONTENTS
Description and Operation 9G-2. . . . . . . . . . . . . . . . . .
Interior Trim Panels 9G-2. . . . . . . . . . . . . . . . . . . . . . . .
Pressure Relief Vent 9G-2. . . . . . . . . . . . . . . . . . . . . . .
Floor Console 9G-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Parking Brake Cable Cover 9G-2. . . . . . . . . . . . . . . . .
Floor Carpet 9G-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Component Locator 9G-3. . . . . . . . . . . . . . . . . . . . . . . .
Interior Trim 9G-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Repair Instructions 9G-4. . . . . . . . . . . . . . . . . . . . . . . . .
On-Vehicle Service 9G-4. . . . . . . . . . . . . . . . . . . . . . . . . .
Front Door Trim Panel (Standard) 9G-4. . . . . . . . . . .
Front Door Trim Panel (Deluxe) 9G-5. . . . . . . . . . . . .
Rear Door Trim Panel (Standard) 9G-6. . . . . . . . . . . .
Rear Door Trim Panel (Deluxe) 9G-7. . . . . . . . . . . . . .
Rear Door Interior Garnish Molding 9G-8. . . . . . . . . .
Rear Door Exterior Garnish Molding 9G-9. . . . . . . . . Tailgate Trim Panel 9G-9. . . . . . . . . . . . . . . . . . . . . . . .
A–Pillar Trim Panel 9G-10. . . . . . . . . . . . . . . . . . . . . . .
Upper B–Piller Trim Panel 9G-10. . . . . . . . . . . . . . . . .
Lower B–Pillar Trim Panel 9G-11. . . . . . . . . . . . . . . . .
C–Pillar Trim Panel 9G-11. . . . . . . . . . . . . . . . . . . . . . .
Rear Parcel Shelf 9G-12. . . . . . . . . . . . . . . . . . . . . . . .
Rear Parcel Side Shelf 9G-13. . . . . . . . . . . . . . . . . . . .
Front Rocker Trim Panel 9G-13. . . . . . . . . . . . . . . . . .
Rear Rocker Trim Panel 9G-14. . . . . . . . . . . . . . . . . . .
Floor Console 9G-15. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Parking Brake Cable Cover 9G-15. . . . . . . . . . . . . . . .
Floor Carpet 9G-16. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Luggage Compartment Wheelhouse
Trim Panel 9G-17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Special Tools and Equipment 9G-18. . . . . . . . . . . . . .
Special Tools Table 9G-18. . . . . . . . . . . . . . . . . . . . . . .

9G –2 INTERIOR TRIM
DAEWOO M-150 BL2
DESCRIPTION AND OPERATION
INTERIOR TRIM PANELS
The interior trim panels are molded plastic and fasten
with screws or plastic clips.
PRESSURE RELIEF VENT
When all the windows are closed and the ventilation sys-
tem is on, the addition of outside air to the interior of the
vehicle causes a positive pressure within the vehicle. In
order to relieve the pressure, air is released through one
pressure relief vents. The pressure relief vent is located
in the luggage compartment, behind the spare wheel.
FLOOR CONSOLE
The floor console fits over the tunnel in the floor of the
vehicle and extends from under the center of the instru-
ment panel to the front seat area. The floor console con-
tains the transaxle shift lever and a cupholder.
The sensing and diagnosis module (SDM) for the airbag
system is located under the floor console.
PARKING BRAKE CABLE COVER
The parking brake cable cover should be removed to ad-
just the free play of the parking brake cable.
FLOOR CARPET
The molded one-piece floor carpet goes over both the
front and the rear floor pans.

INTERIOR TRIM 9G–3
DAEWOO M-150 BL2
COMPONENT LOCATOR
INTERIOR TRIM
D19E402A
1. A–Pillar Trim Panel
2. B–Pillar Upper Trim Panel
3. C–Pillar Trim Panel
4. Front Rocker Trim Panel
5. B–Pillar Lower Trim Panel
6. Rear Rocker Trim Panel
7. Rear Parcel Side Shelf8. Wheel House Trim Panel
9. Floor Console
10. Parking Brake Cable Cover
11. Console Cover Assembly
12. Deposit Box
13. Console Boot Assembly

INTERIOR TRIM 9G–15
DAEWOO M-150 BL2
D19E573A
FLOOR CONSOLE
Removal Procedure
1. Remove the floor console screws.
D19E575A
2. Remove the gear shift lever boot cover and the floor
console.

Remove the gear shift lever boot cover (1).

Remove the screws (2).

Remove the floor console (3).
D19E576A
Installation Procedure
1. Install the floor console.
2. Install the gear shift lever boot cover to the floor con-
sole.
3. Tighten the floor console screws.
D109E577
PARKING BRAKE CABLE COVER
Removal Procedure
1. Remove the parking brake cable cover.

Remove the screw (1).

Remove the cable cover (2).