2003 DAEWOO MATIZ light

INSTRUMENTATION/DRIVER INFORMATION 9E–3
DAEWOO M-150 BL2
COMPONENT LOCATOR
INSTRUMENT PANEL ASSEMBLY
(Left–Hand Drive Shown, Right–Hand Drive Similar)
D19B401A
1. Tie–Bar
2. Tie–Bar Center
3. Instrument Panel Guide
4. Defroster Grille
5. Instrument Panel Upper Cap
6. Passenger’s Airbag Blank Cover
7. Demister Grille
8. Side Ventilation Grille
9. Glove Box Bracket
10. Glove Box11. Instrument Cluster Housing Molding
12. Center Ventilation Grille
13. Switch Blank Cover (Fog Lamp Switch)
14. Hazard Warning Switch
15. Immobilizer LED Indicator Switch
16. Ashtray Bracket
17. Ashtray
18. Ashtray Lamp
19. Cigar Lighter Housing
20. Instrument Cluster Bracket
21. Instrument Panel

INSTRUMENTATION/DRIVER INFORMATION 9E–5
DAEWOO M-150 BL2
DIAGNOSTIC INFORMATION AND PROCEDURES
D19B301B
CIGAR LIGHTER
Condition Probable Cause Correction
Cigar Lighter Inoperative

The open or a short in the power supply
circuit to the fuse F7.

Repair or Replace the wiring
harness.

Fuse F7 is blown.
Replace the fuse F7.





The circuit between the fuse F7 and the
terminal 2 of the cigar lighter connector is
the open circuit or a short circuit.


Repair or Replace the wiring
harness.




Faulty the cigar lighter connector.

Repair or Replace the cigar
lighter connector.

Cigar lighter element is blown.
Replace the cigar lighter.





Open ground (G201) circuit.


Repair the open ground
circuit.

9E–8 INSTRUMENTATION/DRIVER INFORMATION
DAEWOO M-150 BL2
REPAIR INSTRUCTIONS
ON–VEHICLE SERVICE
D109B501
CIGAR LIGHTER
(Left–Hand Drive Shown, Right–Hand
Drive Similar)
Removal Procedure
1. Disconnect the negative battery cable.
2. Remove the ashtray from the ashtray housing.
3. Remove the cigar lighter from the cigar lighter socket.
D19B502A
4. Remove the cigar lighter socket from the cigar lighter
housing.
Caution: Ashtray housing edge could cause seri-
ous injury.

Push out the socket.

Disconnect the electrical connector (1).

Remove the socket (2).
D109B503
Installation Procedure
1. Connect the electrical connector.
2. Install the cigar lighter socket.
3. Install the cigar lighter in the cigar lighter socket.
4. Install the ashtray.
5. Connect the negative battery cable.

INSTRUMENTATION/DRIVER INFORMATION 9E–13
DAEWOO M-150 BL2
D109B518
12. Remove the instrument cluster assembly. Refer to
“Instrument Cluster” in this section.
13. Remove the A/C controller from the instrument. Re-
fer to Section 7B, Manual Control Heating, Ventila-
tion, and Air Conditioning System.
14. Remove the audio system from the instrument pan-
el. Refer to Section 9F, Audio Systems.
15. Disconnect the cigar lighter connector.
16. Disconnect the ashtray lamp if equipped.
D109B519
17. Disconnect the ALDL connector.

Remove the screws (1).

Disconnect the ALDL connector (2).
D109B520
18. Remove the instrument trim panel assembly.

Remove the bolts after removing the caps (1).

Remove the screws on the side plate (2).

Remove the tie–bar retaining bolts on the lower
panel (3).

Remove the instrument trim panel assembly (4).
D109B521
Installation Procedure
1. Install the instrument trim panel assembly with the
bolts and screws.
2. Connect the ALDL connector with the screws.
3. Connect the ashtray lamp if equipped with.
4. Connect the cigar lighter connector.
5. Install the audio system to the instrument panel. Re-
fer to Section 9F, Audio Systems.
6. Install the A/C controller to the instrument panel.
Refer to Section 7B, Manual Control Heating, Ven-
tilation, and Air Conditioning System.

INSTRUMENT/DRIVER INFORMATION 9E–17
DAEWOO M-150 BL2
D109B702
4. Remove the passenger’s airbag module blank cover
from the instrument panel.

Remove the screws.

Remove the passenger’s airbag module blank cov-
er (1).
D109B703
5. Remove the ventilation duct from the instrument pan-
el.

Remove the screws.

Remove the ventilation duct (1).
D109B704
6. Remove the ventilation grilles from the instrument
panel.

Remove the screws.

Remove the ventilation grilles (1).
D109B705
7. Remove the cigar lighter housing from the instrument
panel.

Remove the screws.

Remove the cigar lighter housing (1).

9E –18 INSTRUMENT/DRIVER INFORMATION
DAEWOO M-150 BL2
D109B706
8. Remove the glove box striker and bracket from the
instrument panel.

Remove the screws (1).

Remove the glove box striker and bracket (2).
D109B707
9. Remove the instrument panel guide from the instru-
ment panel.

Remove the screws (1).

Remove the instrument panel guide (2).
D109B708
10. Remove the defroster grilles and the demister grilles
from the instrument panel.
a. Defroster grille.
b. Demister grille.
D109B521
Installation Procedure
1. Install the defroster grilles and the demister grilles to
the instrument.
2. Install the instrument panel guide to the instrument
panel with the screws.
3. Install the glove box striker and the bracket to the in-
strument panel with the screws.
4. Install the cigar lighter housing to the instrument pan-
el with the screws.
5. Install the ventilation grilles to the instrument panel
with the screws.
6. Install the ventilation duct to the instrument panel with
the screws.

9F –2 AUDIO SYSTEMS
DAEWOO M-150 BL2
DESCRIPTION AND OPERATION
STEREO CASSETTE AM/FM RADIO
WITH CD CHANGER AND
RDS/AUDIO SECURITY SYSTEM
The stereo digital logic cassette AM/FM radio with elec-
tronic tape ejection and the stereo digital logic cassette
AM/FM radio with a CD changer located under the front
seat (LH) are optional equipment.
The radio data system (RDS) uses a single button to se-
lect a specific radio station once it is set to the listener’s
preference.
The audio security system is activated whenever the au-
dio system circuit is disconnected from the battery. A
four-digit security code must be entered in order for the
audio system to be functional once again. The security
code is stamped on a card located in the vehicle (usually
in the glove box). One of the following security code en-
tering procedures can be followed.
With RDS
1. With the ignition switch in the I or II position, turn the
radio ON. At this time, “CODE” will be shown on the
radio display.
2. Press the P-UP button until the correct first digit is
shown on the display.
3. Press the P-DN button to move over to the second
digit and then press P-UP once again to enter the cor-
rect second digit.
4. Use steps two and three to enter the third and fourth
digits using the same method.
5. After entering the correct four-digit security code,
press the TP button. “CODE OK” will briefly appear
on the radio display, and the system is ready for use.
Wrong Code
If the wrong code is entered, “ERROR 1” will appear on
the display. After this, “CODE” will appear once again,
and the correct security code can be entered. The timebetween each new coding attempt is doubled; a total of
ten coding attempts can be made.
FRONT AND REAR SPEAKERS
All audio systems use four speakers: two speakers
mounted in the front doors and two speakers mounted in
the rear parcel side shelf.
ROOF ANTENNA
Roof antenna is located on the roof and is designed to
separate the antenna pole from the antenna base. The
antenna pole should be removed to prevent the painting
damage before washing the vehicle. The roof antenna
cannot be adjusted.
TAPE PLAYER AND CASSETTE CARE
The head and the capstan are the two parts of the tape
player that should be cleaned. This service should be
performed every 100 hours of cassette operation.
In order to clean the head and the capstan, use a cotton
swab dipped in rubbing alcohol.
A cassette cleaning kit may also be used to clean the
head and the capstan. Follow the cleaning kit instruc-
tions to clean the tape player.
Do not touch the tape head with magnetized tools. If the
head becomes magnetized, it will degrade cassettes
played in the player. No service is performed on the cas-
settes. The cassette manufacturer handles warranties
of the cassettes. Store cassettes away from extreme
heat and direct sunlight.
COMPACT DISC CARE
Handle discs carefully. Store the discs in protective
cases away from the sun, heat, and dust. If the surface
is soiled, dampen a clean, soft cloth in a solution of mild
neutral detergent and wipe the disc clean. Mini discs
(about 3 inches in diameter), will not eject and should
not be used.

9F –10 AUDIO SYSTEMS
DAEWOO M-150 BL2
D109D561
ROOF ANTENNA
Removal Procedure
1. Disconnect the negative battery cable.
2. Remove the interior courtesy lamp. Refer to Section
9B, Lighting Systems.
3. Remove the roof antenna.

Remove the screw from the vehicle inside (1).

Remove the roof antenna (2).
D19D562A
3 Nm
Installation Procedure
1. Install the roof antenna with the screw.
Tighten
Tighten the roof antenna retaining screw to 3 Nm (27
lb-in).
a. Roof antenna retaining screw.
2. Install the interior courtesy lamp. Refer to Section 9B,
Lighting Systems.
3. Connect the negative battery cable.