2003 DAEWOO MATIZ steering

SUPPLEMENTAL INFLATABLE RESTRAINTS (SIR) 8B–19
DAEWOO M-150 BL2
DTC 03 – Driver Firing Circuit, Short To Ground
Step Action Value(s) Yes No

1


Visually inspect the supplemental inflatable
restraints (SIR) wiring harness for damage.
Is there any visible damage to the SIR harness?
–

Go to Step 2

Go to Step 3

2



1. Replace the SIR wiring harness.
2. Reconnect the negative battery cable.
Is the repair complete?

–



Go to
Diagnostic
System Check


–













3













1. Remove the driver airbag module.
2. Place the driver airbag module in a secure
position with the decorative surface facing
upward.
3. Disconnect the electrical connector at the SDM.

The shorting bar at the disconnected SDM
connector will create a complete circuit be-
tween the wires from the driver airbag
module.
4. Use an ohmmeter to check the continuity
between ground and one of the terminals on the
wiring harness connector for the driver airbag
module.

Refer to ‘‘Diagnostic Illustration 5’’ in this
section.
Is the resistance less than the specified value?











∞












Go to Step 6












Go to Step 4






4






1. Replace the SDM.
2. Reconnect the negative battery cable.
3. Set the scan tool for CODE ERASE.
4. Do the diagnostic system check.

Refer to the “Diagnostic System Check” in this
section.
Does the code 03 still show as a current fault?




–





Go to Step 5





System OK

5


1. Replace the driver airbag module.
2. Reconnect the negative battery cable.
Is the repair complete?
–


Go to
Diagnostic
System Check
–






6







1. Disconnect the clock spring wiring harness
connector at the lower steering column.

The shorting bar at the disconnected SDM
connector will create a complete circuit be-
tween the wires from the clock spring.
2. Using an ohmmeter, check for continuity between
ground and one of the terminals on the SDM side
of the clock spring connector.
Is the resistance less than the specified value?






∞







Go to Step 2







Go to Step 7

7



1. Replace the clock spring.
2. Reconnect the negative battery terminal.
Is the repair complete?


–



Go to
Diagnostic
System Check


–

SUPPLEMENTAL INFLATABLE RESTRAINTS (SIR) 8B–21
DAEWOO M-150 BL2
DTC 04 – Driver Firing Circuit, Short To Battery Voltage
Step Action Value(s) Yes No

1


Visually inspect the supplemental inflatable
restraints (SIR) harness for damage.
Is there any visible damage to the SIR harness?
–

Go to Step 2

Go to Step 3

2



1. Replace the SIR wiring harness.
2. Reconnect the negative battery cable.
Is your repair complete?

–



Go to
Diagnostic
System Check


–












3












1. Remove the driver airbag module.
2. Place the driver airbag module in a secure
position with the decorative surface facing
upward.
3. Disconnect the electrical connector at the SDM.

The shorting bar at the disconnected SDM
connector will create a complete circuit be-
tween the wires from the driver airbag
module.
4. Use a multimeter to check the voltage at one of
the terminals on the wiring harness connector for
the driver airbag module.

Refer to ‘‘Diagnostic Illustration 6’’ in this
section.
Is the voltage greater than the specified value?










0 v











Go to Step 6











Go to Step 4




4




1. Replace the SDM.
2. Reconnect the negative battery cable.
3. Set the scan tool for CODE ERASE.
4. Do the diagnostic system check.
Does the code 04 still show as a current fault?


–



Go to Step 5



System OK


5



1. Replace the driver airbag module.
2. Reconnect the negative battery cable.
Is the repair complete?

–



Go to
Diagnostic
System Check


–









6









1. Disconnect the clock spring wiring harness at the
lower steering column.

The shorting bar at the disconnected SDM
connector will create a complete circuit be-
tween the wires from the clock spring
connector.
2. Using a multimeter, check the voltage at one of
the terminals on the SDM side of the clock spring
connector.

Refer to ‘‘Diagnostic Illustration 7’’ in this
section.
Did the voltmeter indicate the specified value?







0 v








Go to Step 7








Go to Step 2

7



1. Replace the clock spring.
2. Reconnect the negative battery cable.
Is the repair complete?

–



Go to
Diagnostic
System Check


–

SUPPLEMENTAL INFLATABLE RESTRAINTS (SIR) 8B–69
DAEWOO M-150 BL2
REPAIR INSTRUCTIONS
ON–VEHICLE SERVICE
D110B501
DRIVER AIRBAG MODULE
(Left–Hand Drive Shown, Right–Hand
Drive Similar)
Tool Required
DS 401 Torx Bolt Wrench
Removal Procedure
1. Disconnect the negative battery cable.
2. Position the steering wheel straight ahead.
3. Remove the driver airbag module mounting bolts.

Remove the airbag module bolt cover (1).

Remove the airbag module torx bolt using a torx
bolt wrench DS 401.
a. Airbag module torx bolt.
D110B502
Caution: When handling an airbag module, always
keep the top of the unit facing upward. This leaves
room for the module to expand if the module unex-
pectedly deploys. Without room for expansion, a
module suddenly propelled toward a person or ob-
ject can cause injury or vehicle damage.
4.Remove the driver airbag module.

Disconnect the driver airbag module connector (1).

Disconnect the horn terminal connector (2).

Remove the driver airbag module (3).
15 Nm
D1AB503A
Installation Procedure
Caution: When removing an airbag module or han-
dling a new airbag module, always keep the top of
the unit facing upward. This leaves room for the
module to expand if the module unexpectedly de-
ploys. Without room for expansion, a module sud-
denly propelled toward a person or object can
cause injury or vehicle damage.
1. Install the driver airbag module.
2. Connect the connectors to the horn terminal and the
driver airbag module.
3. Install the driver airbag module torx bolt using a torx
bolt wrench DS 401.
Tighten
Tighten the torx bolt to 15 Nm (11 lb-ft)
4. Connect the negative battery cable.

8B–70 SUPPLEMENTAL INFLATABLE RESTRAINTS (SIR)
DAEWOO M-150 BL2
D110B504
CLOCK SPRING
(Left–Hand Drive Shown, Right–Hand
Drive Similar)
Removal Procedure
1. Disconnect the negative battery cable. Wait 1 minute
until the capacitor inside the sensing and diagnostic
module has discharged.
2. Remove the driver airbag module. Refer to “Driver
Airbag Module” in this section.
3. Remove the steering wheel. Refer to Section 6E,
Steering Wheel and Column.
4. Remove the lower/upper steering column cover.

Remove the screws (1).

Remove the lower/upper steering column cover(2).
D110B505
5. Disconnect the clock spring and the horn terminal
connector.
6. Disconnect the clock spring and the horn terminal
connector which are banded on the steering column.
7. Remove the clock spring.

Remove the screws (1).

Remove the clock spring (2).
3 Nm
D1AB506A
D110B507
Installation Procedure
Caution: If the clock spring is not properly aligned,
the steering wheel may not be able to rotate com-
pletely during a turn. Restricted turning ability can
cause the vehicle to crash. Improper alignment of
the clock spring also may make the supplemental
inflatable restraints (SIR) system inoperative, pre-
venting the airbags from deploying during a crash.
Both of these outcomes can result in injury.
Notice: Turning the clock spring more than three turns
clockwise or more than three turns counterclockwise
can damage the spring.
1. Turn the front wheels straight ahead.
2. Install the clock spring with the screws.
Tighten
Tighten the clock spring mounting screws to 3 Nm
(27 lb-in)
Important: The clock spring may come packed in mate-
rial used to prevent damage to the spring during ship-
ping or storage. Avoid installing any of the packing
material with the clock spring.
3. Turn the label of the clock spring clockwise to lock.
4. Turn the label of the clock spring counterclockwise
approximately three turns to the neutral positions with
the front wheels ahead.

SUPPLEMENTAL INFLATABLE RESTRAINTS (SIR) 8B–71
DAEWOO M-150 BL2
5. Properly align the pointed marks () on the com-
ponents of the clock spring.
6. Connect the electrical connectors on the lower
spring steering column.
7. Install the lower/upper steering column cover.
8. Install the steering wheel. Refer to Section 6E,
Steering Wheel and Column.
9. Connect the driver airbag module and the horn con-
nectors.
10. Install the driver airbag module. Refer to “Driver air-
bag module” in this section.
11. Connect the negative battery cable.
D110B508
PASSENGER AIRBAG MODULE
(Left–Hand Drive Shown, Right–Hand
Drive Similar)
Tool Required
DS 401 Torx Bolt Wrench.
Removal Procedure
1. Disconnect the negative battery cable.
2. Remove the glove box. Refer to Section 9E, Instru-
ment/Driver Information.
3. Disconnect the passenger airbag module connector.
D110B509
4. Remove the passenger airbag module.

Remove the nuts (1).

Remove the airbag module torx bolts using a torx
bolt wrench DS 401.
a. Passenger airbag module torx bolt.

Remove the passenger airbag module (2).
15 Nm 10 Nm
D1AB510A
Installation Procedure
1. Install the passenger airbag module.
2. Install the passenger airbag module mounting torx
bolts and the nuts using a torx bolt wrench DS 401.
Tighten

Tighten the passenger airbag module torx bolts to
15 Nm (11 lb-ft).
a. Passenger airbag module torx bolt.

Tighten the passenger airbag module nuts to 10
Nm (89 lb-in).
b. Passenger airbag module nut.
Notice : Do not reuse the removed torx bolts.
Replace the torx bolts with the new ones.

8B–74 SUPPLEMENTAL INFLATABLE RESTRAINTS (SIR)
DAEWOO M-150 BL2
D110B010
AIRBAG MODULE DEPLOYMENT
(IN VEHICLE)
(Left–Hand Drive Shown, Right–Hand
Drive Similar)
Deploy the airbags before disposing of them. This in-
cludes those in a whole vehicle being scrapped.
If the vehicle is still within the warranty period, contact
the Daewoo regional service manager for approval or
special instructions before deploying the airbag mod-
ules.
Caution: Before deploying the airbags, remove all
loose objects from the airbags expansion area.
Caution: Deploy the airbags with the vehicle doors
closed and the side windows open.
Caution: Deploy the airbags only in an evacuated
area. Service personnel who must be present dur-
ing the deployment should be at least 10 meters
(33 feet) in front of the vehicle.
Caution: Do not connect the voltage source until af-
ter having completed all other preparations for the
deployment of the airbags.
Caution: Allow a deployed airbag module to cool
for at least 30 minutes before handling.
Caution: Wear the gloves and the eye protectors
during the disposal process.
Caution: If the deployment fails, disconnect the volt-
age source and wait 5 minutes before approaching
the vehicle.
Deployment Procedure
1. Disconnect both battery cables and place the battery
at least 10 meters (32.8 feet) from the vehicle.
Caution: Wait 1 minute after disconnecting both
battery cables to allow the capacitor inside the
sensing and diagnostic module (SDM) to discharge
before taking any other action. The capacitor sup-
plies the reserve power to deploy the airbags, even
if the battery is disconnected. Unintentional deploy-
ment of the airbags can cause injury.
2. Remove the lower cover from the steering column.
3. At the lower steering column, cut the two wires lead-
ing from the supplemental inflatable restraint (SIR)
harness to the clock spring.
4. Strip 13 mm (0.5 inch) of insulation from the ends of
the wires leading to the clock spring.
5. Use two additional wires, each at least 10 meters
(33 feet) long, to reach from the deployment battery
to the airbag module.
6. Strip 13 mm (0.5 inch) of insulation from the ends of
these two additional wires.
7. Twist the two wires together at one end.

9B – 2 LIGHTING SYSTEMS
DAEWOO M-150 BL2
DESCRIPTION AND OPERATION
HEADLAMPS AND PARKING LAMPS
The headlamps are controlled by the multifunction lever
located on the left side of the steering column. They will
come on with the ignition switch in any position. Turning
the headlamp switch to the first position turns on the
parking lamps, the license plate lamps and the instru-
ment panel illumination. Turning the switch to the sec-
ond position turns on all of the previous lamps and the
headlamps. Turning the switch to the off position turns
off all the lamps.
The parking lamps can be turned on by turning the light-
ing switch to the first position. The parking lamps can be
turned off by turning the switch to the OFF position.
Headlamp high beam and low beam are also controlled
by this lever. When the headlamps are on, pushing the
lever away from the driver until the switch clicks
changes the lamp from low beam to high beam. An indi-
cator lamp on the instrument cluster assembly will come
on when the high beam headlamps are on. To return the
headlamps to low beam, pull the lever toward the driver.
The headlamps must be aimed for proper illumination of
the road. Headlamp aim should be checked whenever a
new headlamp assembly is installed or service repairs to
the front end area may have disturbed the headlamp as-
sembly or its mountings.
FRONT TURN SIGNAL LAMPS
When the turn signals are activated, the side turn signal
lamps flash to signal a turn. The turn signal works only
when the ignition switch is on.
The turn signals are controlled by the light switch on the
left side of the steering column. Moving the lever all the
way up or down (past the detent) will turn on the turn sig-
nals. When the turn is completed, the lever will return to
horizontal and the turn signals will stop flashing.
For changing lanes or shallow turns where the steering
wheel does not turn far enough to cancel the signal,
move the signal only to the first detent and hold it there.
When the lever is released, it will return to horizontal and
the turn signal will cancel.
REAR FOG LAMP
The rear fog lamp is incorporated in the drive side tail-
lamp assembly and are controlled by the rear fog lamp
switch on the instrument panel. The rear fog lamp can
be turned on only when headlamps are on.
TAILLAMPS
The taillamps, stoplamps, backup lamp(s), rear fog lamp
(if equipped with) and turn signal lamps are one assem-
bly.
Turning on either the headlamps or the parking lamps
will also turn on the taillamps. When the brake pedal is
pushed, the taillamps will glow brighter to serve as sto-
plamps.
The center high-mounted stoplamp is located in the rear
window and will come on when the brake pedal is
pressed.
LICENSE PLATE LAMPS
The license plate lamps will come on when the head-
lamps or the parking lamps are on. The license plate
lamps are mounted on the rear bumper, above the li-
cense plate.
INTERIOR COURTESY LAMP
The courtesy lamp is located on the headliner just be-
fore the front seats. The lamp switch has three posi-
tions. If the switch is in the center position, the lamp will
go on whenever a door is opened and go off when it is
closed. In the ON position, the lamp will stay on until it is
turned off. In the OFF position, the lamp will not come
on, even when a door is opened.
BACKUP LAMP(S)
The backup lamps are located in the rear combination
lamps. They will come on when the transaxle is shifted
into REVERSE. On a vehicle with a manual transaxle,
they are activated by a reverse switch which is part of
the transaxle.
DAYTIME RUNNING LAMPS (DRL)
(W/Europe Only)
The daytime running lamps (DRL) work in conjunction
with the exterior lamps system. When the ignition switch
is turned to the ”II” position with the light switch off, park-
ing, tail, license plate and instrument panel lights illumi-
nate. And, when the engine is started, the headlamps
(low beam) also come on.
They remain on until the ignition switch is turned off or
the light switch is turned on. They revert to normal op-
eration when the light switch is on.
The daytime running lamps (DRL) is optional.

9C – 2 HORN
DAEWOO M-150 BL2
DESCRIPTION AND OPERATION
HORN
The horn is located under the hood. It is attached near
the radiator at the front of the vehicle. The horn is actu-ated by pressing the steering wheel pad, which grounds
the horn’s electrical circuit.