2003 ASTON MARTIN DB AR1 Q lights

B - Controls
1-B-12
Steering Column Controls - Left Hand Stalk
The left column stalk controls the following functions:
Turn Signals
Move the stalk up to indicate a right turn, or down to indicate a left turn. The
stalk automatically returns to the centre position on completion of the
manoeuvre. The stalk may be moved partially up or down to bring on the
indicator lights to indicate a lane change. When released from the partially
up or down positions, the stalk is returned to the centre position by spring
pressure.
If an external indicator bulb fails, the remaining indicator lights on that side
of the car and the instrument panel warning light for that side will flash at
twice the normal rate when a turn to that side is indicated. If this situation
occurs, replace the defective bulb as soon as possible.

B - Controls
1-B-13
Side and Headlight Switching
The left stalk collar has three positions that control the external running lights
of the vehicle: in the off position all external lights are off.
Rotating the collar to the first click (the side lamp symbol) switches on the
side lights, side marker lights, rear lights and registration plate lights (licence
plate lights).
Rotating to the second click position (the headlamp symbol) switches on the
headlight dipped beams in addition to the side, side marker, rear and
registration plate (licence plate) lights.
Main and Dipped Beam Switching
When the headlight dipped beams are switched on, they may be switched
to main beams by pushing the left stalk away from the steering wheel. Pulling
the left stalk back to its central position will switch the headlights back to
dipped beams.
Headlight Flashing
When all lights are off or when only the side lights are on, the headlight main
beams may be flashed by pulling the left stalk towards the steering wheel.
The headlights will go off when the stalk is released.

B - Controls
1-B-18
Fog Lights, Screen Heater and Seat Heater Switches
The row of controls beneath the air-conditioning panel contains a variety of
switches dependant on model and market. Your DB AR1 will have an
appropriate selection of the switches described below.
Front Fog Lights
The front fog lights can be switched on when the headlights
or sidelights are in use. They must be switched off when
visibility clears to reduce glare to the drivers of oncoming
vehicles.
Rear Fog Lights (Where fitted)
These lights may only be used in conjunction with the
headlamps or sidelamps. They should be switched on when
fog is causing restricted visibility. They must be switched off
when visibility clears to reduce glare to the drivers of
following vehicles.
Heated Front Screen
This switch controls the front windscreen heater which
turns off automatically after about 4 minutes if not turned
off manually.

B - Controls
1-B-19 Seat Heater Switches
Press to switch on the heater. Press the button a second
time to switch off the heater. The heater is thermostatically
controlled and maintains a constant seat temperature until
either the heater is switched off or the ignition is switched
off.
Boot Release Switch
Press to open the boot at any time when the alarm system
is switched off and the ignition is switched on.
Radio/Cassette/CD Player
The radio/cassette player is located beneath the console switch panel. The
CD changer is fitted in the boot (trunk). Manufacturers operating instructions
for the in-car entertainment system are included with this Owner's Guide.
Hazard Warning Lights
The hazard warning light switch is located beside the
radio cassette player. When pressed, the external indicator
lights and side repeater lights will flash in unison.
Press the switch again to turn off the hazard lights.
Caution: Observe local laws on the use of hazard lights

B - Controls
1-B-27
Interior Lights
The interior light assembly is mounted in the front windscreen header rail
and contains two 'eyeball' lamps and the front interior lamp. The 'eyeball'
lamps are controlled by the outer switches on the lamp assembly and may
be rotated to illuminate the driver or passenger seat areas.
The centre switch on the lamp assembly controls the operation of the front
and rear interior lights as follows:
Front and rear interior lights on
Front and rear interior lights off
Front and rear interior lights come on when a door is opened and
remain on for approximately 12 seconds after a door is closed with
the ignition off.
12 sec

C - Driving
1-C-2
Checks Before Driving
Inspect the car to make sure that everything is according to the information
and specifications in this Owner's Guide.
Check the wheels, wheel nuts and tyres.
Check that all windows, mirrors and lights are clear and unobstructed.
Check that the boot and bonnet are closed.
Once you are in the car, check that the doors are closed.
Check that the seat, mirrors and steering wheel adjustments are correct.
Check that all gauges and indicators are reading correctly.
Check that the seat backs are in an upright position.
Check that all occupants have fastened their seat belts.
Fuel
DB AR1 uses 95/98 RON Unleaded Fuel only (USA - Premium Unleaded).
For optimum performance and extended high speed driving, the use of 98
RON fuel is recommended.
Caution: Do not use unleaded petrol containing metal based additives, such as those
based on Manganese (often sold as MMT) and Iron (often sold as Ferrocene). The use
of fuel containing such additives could lead to catalyst failure which is not covered by
the vehicle warranties.
The DB AR1 total fuel capacity is 82 litres (18 Imp gallons / 21.5 US gallons).
Note: Approximately 7 litres of the total fuel capacity specified above is required
to prime the fuel system and is therefore not usable.

C - Driving
1-C-6
Warning Light Indications at Ignition On
As the ignition is switched on, the DB AR1 electronic control units each
complete a self check to ensure correct operation. During these checks, the
warning lights on the instrument panel will illuminate as follows:
• Bulb Check - All warning lamps illuminate for about three seconds as a
bulb check. (The Sport and Transmission Fail lamps are not illuminated
on manual transmission vehicles).
• The Ignition and Oil Pressure warning lights illuminate until the engine
starts.
• The Check Engine light will illuminate during the engine management
self-check and will extinguish when the starter button is pressed.
• The Seat Belt warning light illuminates and a gong sounds for six seconds
if the driver's seat belt is not fastened. On fastening the seat belt, the gong
immediately ceases. The warning lamp extinguishes at the end of the six
second warning period.
• The ABS and Traction Control warning lights illuminate and extinguish
if the system self checks are satisfactory.
• The Brake warning light will illuminate and extinguish if the brake fluid
level is within specification.
• The SRS Airbag warning light will illuminate and extinguish if the SRS
Airbag control system check is satisfactory.
Only the handbrake (parking brake) warning light should stay on after the
engine has started and is running correctly. The handbrake warning light will
extinguish as the handbrake is fully released.
Note: Other Information lights may remain on (e.g. Main Beam Warning or Low
Screen Wash) dependant on the vehicle state and switch settings at the time.

C - Driving
1-C-7 If either the ABS or Brake Fluid Warning lights remain illuminated, refer to
the description of Brake Warnings during Driving later in this section.
Starting the Engine - Hot or Cold
WARNINGS:
Before driving the vehicle, ensure that you are wearing appropriate footwear to
efficiently operate the floor mounted pedals.
Ensure that floor mounted pedal movement is not restricted by floor mats or
other objects trapped beneath the pedals.
Manual Transmission - The engine can only be started with the clutch
pedal fully depressed.
Touchtronic Transmission - The engine can only be started when the gear
selector lever is in Park or Neutral.
Place the gear selector lever in Neutral (Park on Touchtronic vehicles) and
check that the handbrake is applied. Fully depress the clutch pedal on
manual transmission vehicles.
Insert the ignition key and rotate it to position II. Press the
starter button, wait until the engine fires, then release the
starter button.
Note: Do not press the accelerator during engine starting. The Electronic Engine
Management System automatically compensates for cold or hot start conditions
and makes appropriate adjustments to the fuel/air mixture and engine idle speed
without driver intervention.