2003 ASTON MARTIN DB AR1 Q run flat

C - Driving
1-C-9
Running-In
Your DB AR1 engine is fully hot tested during manufacture and no special
running-in procedures are necessary. Nevertheless it is prudent to limit
engine loads (e.g. by using lower gears on steep hills) during the first 4,000
km (2500 miles).
Maximum Engine Speed - Fuel Cut-Off
The maximum safe engine speed is 7,000 RPM on manual transmission
vehicles (6,400 RPM on auto and touchtronic transmission cars). If this
speed is exceeded, fuel supply to the engine is gradually reduced. As the
engine speed reduces back to a safe level, fuel supply is progressively
restored.
Driving in Wet Conditions
When driving in wet conditions, water can build up under your tyres so that
they ride on a layer of water. This is called aquaplaning or hydroplaning.
When this happens, you have little or no control. Aquaplaning is more prone
to happening at higher road speeds if there is a lot of water on the road and
particularly if the tyres are also under inflated or approaching minimum
tread depth. Slow down when it is raining.
It is important to take bends or curves at a safe, reasonable speed,
particularly when driving on wet or slippery road surfaces.
Rapid acceleration or deceleration can cause loss of control, especially on
slippery surfaces. Use extra care when driving on such surfaces.

F - Owner Maintenance
1-F-22
Jacking and Wheel Changing
WARNINGS:
The front road wheels must be in the straight ahead position before removal. The
front tyre will catch on the wheel arch during removal if not in the "straight
ahead" position.
Check that the temporarily repaired tyre is inflated to the specified pressure.
Never exceed 50 km/h (30 mph) when a temporarily repaired wheel is fitted.
Ensure that no persons are in the vehicle before jacking commences.
Ensure that the handbrake (parking brake) is set and that the car is in 'Park' (Auto)
or 1st Gear (Manual).
Ensure that the vehicle is parked on firm and level ground to ensure a secure base
for the jack.
Do not run the engine while the car is on the jack and never let anyone work
under the car whilst it is on the jack.
Spare Wheel Access (where fitted)
On vehicles with the space saver spare
wheel, the spare wheel is stored in a
well in the boot floor.
Lift out the boot floor and toolkit.
Remove the spare wheel retaining screw
and lift out the spare wheel.

F - Owner Maintenance
1-F-36
Electrical Start from Another Vehicle
If your DB AR1 will not start due to a discharged battery, it may be started
by connecting the battery from another vehicle to the discharged battery.
Before the vehicle is started in this way, ensure that the donor vehicle has
a 12 volt battery and negative (-), black earth terminal to ensure that the
correct battery polarity is maintained.
WARNING: If the voltage or earth of the donor vehicle is different or not known,
do not attempt starting in the way described.
1. Position the vehicles so that the connecting cable will reach between
the batteries. Ensure that the vehicles do not touch each other.
2. To lessen the risk of an electrical short circuit, remove rings, metal
watch bands and any other jewellery. Wear eye protection when
working near the battery. Turn off all electrical motors and ancillaries
in both vehicles. Switch off all lights except those needed to protect the
vehicles or illuminate the work area. Switch off the ignition and apply
the handbrake.
3. Lift out the boot floor panels to gain access to the battery.
4. Connect the red (+) cable between the red (+) positive terminal of the
two batteries.
5. Connect the black (-) cable between the black (-) negative terminals of
the two batteries.
6. Start the donor vehicle engine and run at about 1500 - 2000 rpm.
7. Start the engine. Allow the engine to run for some minutes until the flat
battery is partially charged. Switch off both vehicles.

F - Owner Maintenance
1-F-58
Storing the Car - Recommendations
Note: These recommendations apply to new and pre-owned cars either in
Dealer or customer ownership.
When ever the car is not in use always cover the car with it's fabric cover.
If the vehicle is not to be used for periods up to six months it should be stored
in a dry, well ventilated building.
Drive the car for a sufficient distance to warm the oil in the engine, torque
convertor, transmission and final drive unit; this ensures complete lubrication
of the internal components.
Check the engine coolant level. Top up if necessary with the correct
antifreeze/water solution.
In order to take the weight off the tyres, raise the car with a jack and place
supports under the front and rear suspension.
If the vehicle is not raised from the ground, increase the tyre pressures to 3.4
bar 340 kpa 50 psi. Cover the tyres to exclude any light. Rotate the wheels
1/4 turn every month to avoid tyre flat spots.
The battery should be removed and cleaned. Fully charge the battery on a
trickle charger and recharge once a month.
Once a month
Reconnect the battery and ventilate the storage area. Start and run the
engine until fully warmed up. Check that there are no fluid leaks. Check
and correct the tyre pressures if necessary.
Run the Air Conditioning system to keep the internal parts of the Air
Conditioning system lubricated.