2003 ASTON MARTIN DB AR1 Q low beam

B - Controls
1-B-5 AMBER is used for non-emergency indications such as Low Fuel, Low
Screen Wash Fluid.
GREEN signals the use of normal functions such as Direction Indicators and
Sport Mode engagement.
BLUE is used to indicate that the Headlight Main Beams are on.
The following descriptions cover all instrument panel warning lights grouped
in the order warnings (reds), cautions (ambers), and normal status lights
(greens and blue).

B - Controls
1-B-9 Headlights (Blue)
Shows when the main beam of the headlights are in use.
Instrument Pack Chime
A warning chime will sound briefly to attract your attention if any of the
following warning lamps illuminate - ABS, Low brake fluid, Low coolant
level, Low fuel level, Low oil pressure, Boot open or a Frost warning.
The warning will be repeated each time the ignition is switched on until the
cause is cleared.
Instrument Panel Illumination
The level of instrument illumination can be adjusted using the rotary control
on the left hand side of the steering column.

C - Driving
1-C-6
Warning Light Indications at Ignition On
As the ignition is switched on, the DB AR1 electronic control units each
complete a self check to ensure correct operation. During these checks, the
warning lights on the instrument panel will illuminate as follows:
• Bulb Check - All warning lamps illuminate for about three seconds as a
bulb check. (The Sport and Transmission Fail lamps are not illuminated
on manual transmission vehicles).
• The Ignition and Oil Pressure warning lights illuminate until the engine
starts.
• The Check Engine light will illuminate during the engine management
self-check and will extinguish when the starter button is pressed.
• The Seat Belt warning light illuminates and a gong sounds for six seconds
if the driver's seat belt is not fastened. On fastening the seat belt, the gong
immediately ceases. The warning lamp extinguishes at the end of the six
second warning period.
• The ABS and Traction Control warning lights illuminate and extinguish
if the system self checks are satisfactory.
• The Brake warning light will illuminate and extinguish if the brake fluid
level is within specification.
• The SRS Airbag warning light will illuminate and extinguish if the SRS
Airbag control system check is satisfactory.
Only the handbrake (parking brake) warning light should stay on after the
engine has started and is running correctly. The handbrake warning light will
extinguish as the handbrake is fully released.
Note: Other Information lights may remain on (e.g. Main Beam Warning or Low
Screen Wash) dependant on the vehicle state and switch settings at the time.

F - Owner Maintenance
1-F-44
Headlight Dipped Beam Bulb Replacement
The dipped beam lights are accessed through panels in the wheel arch liners.
1. Turn the steering to the opposite lock to the defective light (i.e. full right
lock to access the left dipped beam light and vice versa).
2. Using a screwdriver from the tool kit, release the quarter turn fastener on
the access cover in the wheel arch liner and remove the cover.
3. Remove and replace the bulb following the instructions for the main
beam on the previous page.
4. Refit and secure the access cover.

F - Owner Maintenance
1-F-45
On Board Headlight Aiming (where fitted)
The headlight assemblies (main and dipped beam lights) are factory set to
give correct forward illumination under average load conditions. Should
your headlight aiming require adjustment, it may be corrected as follows:
1. Ensure that the tyres are inflated to the specified pressures.
2. Fill the car with fuel.
3. Park the car on level ground.
NOTE: Any error in ground level will adversely influence the accuracy of the
vertical beam alignment check
4. Have an adult person sit in the drivers seat.
5. Load the boot with the normal items you carry.
6. Open the bonnet.
Horizontal Beam Alignment Check
1. Check the gauge labelled Horizontal Angle Gauge. The green line on the
collar must be aligned with the pointer at the side of the spirit level. If
adjustment is required, rotate the screw and collar until the green line
is aligned with the pointer.

F - Owner Maintenance
1-F-46
Vertical Beam Alignment Check
1. Check the position of the bubble in the Vertical Angle Spirit Level. Rotate
the lower screw if necessary to align the bubble centrally between the
reference lines of the level
If you have any difficulty in getting the indicators to align, take your car to
an Aston Martin dealer for service.