2003 ASTON MARTIN DB AR1 Q lights

F - Owner Maintenance
1-F-47
Front Indicator Lights / Front Fog Lights / Front Parking Lights
1. Using the screwdriver from the tool kit, remove three screws and remove
the lamp assembly from the front apron.
2. If preparing to replace the front fog lamp (C), release the rubber seal from
the lamp housing.
3. Turn the appropriate bulb holder (Indicator - A, Parking Lamp - B, Fog
Lamp - C) a quarter turn anticlockwise and remove it.
4. Pull the defective bulb from the bulb holder and fit the replacement
bulb.
5. Refit the bulb holder to the lamp assembly and, if necessary, refit the
rubber seal to the fog lamp
6. Refit the lamp assembly to the car and secure with three screws.

F - Owner Maintenance
1-F-48
Side Repeater Lamps
1. Taking care to protect the paint work,
push the side repeater lamp and rotate a
quarter of a turn anticlockwise. Withdraw
from the front wing.
Note: Take care not to let the bulb holder fall
into the front wing.
2. Holding the bulb holder, rotate the lens
a quarter of a turn anticlockwise.
Withdraw the lens. Replace bulb and
reassemble the side repeater lamp.
3. Push the side repeater lamp to the wing and rotate a quarter of a turn
clockwise.
Side Marker Lights
1.Taking care to protect the paint work, push the side marker light and rotate
a quarter of a turn anti-clockwise. Withdraw from front wing.
NOTE: Take care not to let the bulb holder fall into the front wing.
2. Holding the bulb holder, pull the lens complete with bulb from the bulb
holder. Replace bulb and re-assemble the side marker light.
3. Push the side marker light to the wing and rotate a quarter of a turn
clockwise.

F - Owner Maintenance
1-F-49
Rear Lights - (Indicators, Stop/Rear)
The indicators and stop/rear lights are contained in two clusters, one either
side of the car. The replacement technique for all rear light bulbs is similar.
1. Remove the boot trim panel.
2. Remove two knurled nuts and withdraw the blub holder.
3. Push and rotate the blub a quarter of a turn anti-clockwise. Withdraw
from bulb holder.
NOTE: The stop/rear light bulb has two filaments and offset bayonet pins. Ensure
correct orientation when fitting.
4. Insert the new bulb. Push and rotate bulb a quarter of a turn clockwise.
5. Place the bulb holder back to the light cluster and secure with the two
knerled nuts. Install the boot trim.

F - Owner Maintenance
1-F-50
Rear Lights - (Reversing)
1. Remove outer trim panel (three allen key head bolts).
2. Each bulb holder is held in place with three screws. Remove the bulb
holder containing the defective bulb.
3. Replace bulb. Refit bulb holder and outer trim panel.
Number Plate Lights
1. Lever / Unscrew the light unit from the bumper. Be carefull not to
damage paint work.
2. Pull the defective bulb form its holder and replace with a new one.
3. Replace the number plate light unit

F - Owner Maintenance
1-F-51
Rear Interior Quarter Lights
1.Insert a small screwdriver into the
lever slot in the light lens and lever
out the lens assembly.
2.Remove the defective bulb from its
clips and replace with a new one.
3.Press the light lens assembly back
into its housing until it clips into
position.
Front Interior Lights
1. Release the quarter turn fastener on the front interior light assembly and
lower the assembly from the roof liner.
2. To replace an interior light festoon bulb, pull the defective bulb from its
clips and insert a new one.
3. To replace a map reading light bulb, swing the bulb contact away from
the bulb. Lift out the defective bulb and fit a replacement. Swing the bulb
contact back to its original position.
4. Refit the light assembly to the roof lining and secure by turning the
quarter turn fastener clockwise.

F - Owner Maintenance
1-F-52
Door Edge Lights
1. Taking care to protect the paint
work, use a screwdriver to lever the
light assembly from its location in
the lower door edge.
2. Remove the bulb from the light
assembly and fit a replacement bulb.
3. Refit the assembly to the door,
pushing firmly until it clips into place.
Central High Mounted Stop Lamp
The high mounted stop lamp is fitted in the boot lid. It is recommended that
your have your dealer change the high mounted stop lamp if necessary.
Electric Window Reset Procedure
If either the battery or the window controllers are disconnected, the window
controller will lose its memory of the window maximum up and down
positions. The window controller memory may be checked and reset as
follows:

F - Owner Maintenance
1-F-60
Recommissioning After Storage
Provided that the car has been stored in accordance with the recommended
procedure, the following points only should require attention before using
the car on the road.
Check the tyre pressures, inflate if necessary and lower the car to the ground.
Fully charge and refit the battery. Reset the clock and electric windows.
Drain the engine sump and final drive unit, fit a new engine oil filter element,
then refill with the approved oils. Check the coolant level and if necessary
top up with the correct antifreeze/water solution.
Check all fluid levels and top-up as necessary. Fill the fuel tank
Caution: Starting the engine without sufficient lubrication can cause serious engine
damage. Take care to establish engine oil pressure as directed in the following steps
before allowing the engine to start.
Press and hold the accelerator hard to the floor (kickdown switch actuated).
This will temporarily inhibit the fuel injectors during cranking. Turn on the
ignition. Press and hold the starter button to crank the engine until normal
oil pressure is indicated on the oil pressure gauge. Release the starter button
and the accelerator pedal.
Start the engine normally and check that the oil pressure and ignition
warning lights go out as the engine starts indicating correct oil pressure and
battery charging. Raise the bonnet and check for leaks of fuel, oil and
coolant.
Finally, check the operation of all instruments, lights and accessories.

G - Specifications
1-G-1
Contents
Body ................................................................................................. 1-G-2
Engine ............................................................................................... 1-G-2
Power and Torque Graphs ................................................................. 1-G-3
Transmission - Manual....................................................................... 1-G-4
Transmission - Automatic ................................................................... 1-G-4
Final Drive ......................................................................................... 1-G-4
Steering ............................................................................................. 1-G-4
Suspension........................................................................................ 1-G-5
Brakes ............................................................................................... 1-G-5
Towing .............................................................................................. 1-G-5
Wheels and Tyres .............................................................................. 1-G-6
Exterior Features ................................................................................ 1-G-7
Interior Features ................................................................................ 1-G-7
Lights ................................................................................................ 1-G-8
Exterior Dimensions and Clearances.................................................. 1-G-9
Interior Dimensions .........................................................................1-G-10
Weights ........................................................................................... 1-G-10
Capacities........................................................................................ 1-G-11
Recommended Fluids ......................................................................1-G-12