2002 TOYOTA LAND CRUISER Navigation Manual

55
UN100
3. Add a way point in the same way as
you input the destination.
You can set up to 5 way points.
After adding a way point, the screen
changes and displays the map location of
the way point and route preference. (See
ºEntering Destinationº on page 19.) 1. Touch the
ºDeleteº switch to display
the Delete Way Point screen.
UN101
2. Select the way point you want to delete
and touch the
ºDeleteº switch.
UN102
3. A selected point and above message
appear. To delete the point, touch the
ºYESº switch. If you want to try again or
cancel the deletion, touch the
ºNOº
switch. The previous screen will return.
INFORMATION
When the vehicle is in motion, ºDelete
Nextº instead of ºDeleteº is dis-
played.
(c) Deleting a way point

56
UN103
When the vehicle is in motion, only the
next way point can be deleted. Touch the
ºDelete Nextº switch. Any points you want to avoid due to traf-
fic jams, construction work or other rea-
sons can be registered as avoid points.
Push the
ºMENUº button on the bezel
to display the menu screen and then
touch the
ºAvoid Point/Areaº switch
to display the following screen.
un137
INFORMATION

Some areas and freeways may not be able to be set as an avoid point.

If a destination is input in the avoidarea or the route calculation cannotbe made without running throughthe avoid area, a route passingthrough the avoid area may beshown.
(d) Deleting the next way
point
Avoid Point/Area

57
1. Touch the
ºRegister Avoid Point/
Areaº switch.
UN104
2. Enter the avoid point location in the
same way as you input any destination or
display the map of the area you want to
avoid. (See page 6 through 19.)
UN105
3. Depending on the contents to be
edited, touch either the ºReduceº orºEnlargeº switch or one of the arrows.
When you touch the
ºEnterº switch, the
following message appears.
UN106
After a few seconds, the avoid point/area
screen returns. 1. Touch the
ºEdit Avoid Point/
Areaº switch to display the Edit Avoid
Point/Area screen.
UN107
2. Touch the point you want to edit from
the list.
(a) Registering avoid point/area (b) Editing avoid points

58
UN108
3. Depending on the contents to be
edited, touch either the ºReduceº orºEnlargeº switch or one of the arrows.
When editing is completed, touch the
ºEn-
terº
switch.
INFORMATION

If you try to change the map to an in-
appropriate scale, a message ap-pears.

For enlargement or reduction of themap scale, see page 33.
1. Touch the ºDelete Avoid Point/
Areaº switch to display the Delete A void
Point/Area screen.
UN109
2. Select the point you want to delete
from the list.
Delete All: All avoid points registered in the
system are deleted.
UN110
UN111
3. Either of the above messages appears.
To delete the point(s), touch the
ºYESº
switch.
If you touch the
ºYESº switch, the data
cannot be recovered.
If you want to try again or cancel deletion,
touch the
ºNOº switch. The previous
screen will return.
(c) Deleting avoid point/area

59
The current vehicle position mark will be
automatically corrected during driving
on reception of GPS signals. If your ve-
hicle cannot receive GPS signals, you
can correct the current position mark
manually.
UN112
1. Push the ºMENUº button on the bez-
el to display the ºMenuº screen, and then
touch the
ºSystem Optionº switch.
UN113
2. Touch the ºPositionº switch.
INFORMATION
For additional information on current position accuracy, see ºLimitations ofthe Navigation Systemº on page 35.

Position
UN114
1. Touch the scroll arrows to move the
cursor to your desired location.
Touch the
ºEnterº switch.
Current Position Calibration

60
UN115
2. Touch either the left or right arrow to
correct the direction of the current ve-
hicle position mark on the road.
Touch the
ºEnterº switch on the screen
and the map screen returns.

Distance
The distance calibration function is to be
used when the tires are replaced. This
will adjust for any possible change in tire
circumference from the old tires to the
new ones. If this procedure is not per-
formed when tires are replaced, the cur-
rent vehicle position mark may become
incorrect.
To execute the fast distance tire calibration
procedure, touch the
ºDistanceº switch
on the System Option screen.
UN116
The above message appears and the fast
distance calibration is automatically started.
A few seconds later, the map screen returns.

61

i
Changing the route
guidance
s-007u
When you touch this switch, the Change
Route screen will appear. For details, see
page 22.
One - touch registra-
tion of marked point
s-008u
To register the current vehicle position as a
marked point. For details, see page 53.
Display of point of
interest
s-009u
Symbols such as restaurants and hotels,
etc.
can be displayed on the screen. For de-
tails, see page 29.
Deletion of point of
interest
s-010u
Symbols such as restaurants and hotels,
etc.
displayed on the screen can be deleted.
For details, see page 30. Heading-up symbol
and scale of map
On the map, the vehicle travel direction is up.
The red arrow indicates North. Touc
hing this
symbol directly on the screen changes the
map to North-up. For details, see page 35.