2002 MAZDA 6 Workshop Manual Suplement

U–18
CONTROL SYSTEM
1K Ambient
temperature
sensor inputAmbient
temperature sensorDepends on temperature
surrounding sensor
See Figure
2•Inspect for continuity
(Climate control unit—
ambient temperature
sensor: 1K—B, 1I—A)
•Inspect for short circuit
(Climate control unit—
ambient temperature
sensor: 1K—B)
•Inspect ambient
temperature sensor
•Inspect terminal voltage of
climate control unit (2H, 2L)
1L MZR-CD (RF
Turbo) selectGround Under any condition
Below 1.0•Inspect for continuity
(Climate control unit—
ground: 1L—GND)
•Inspect center panel
1M Cabin
temperature
sensor inputCabin temperature
sensorDepends on temperature
surrounding sensor
See Figure
3•Inspect for continuity
(Climate control unit— cabin
temperature sensor: 1M—B,
1I—A)
•Inspect for short circuit
(Climate control unit— cabin
temperature sensor: 1M—B)
•Inspect cabin temperature
sensor
•Inspect terminal voltage of
climate control unit (2H, 2L)
1N—— —— —
1O Water
temperature
sensor inputWater temperature
sensorDepends on temperature
surrounding sensor
See Figure
4•Inspect for continuity
(Climate control unit—water
temperature sensor: 1O—A,
1I—B)
•Inspect for short circuit
(Climate control unit—water
temperature sensor: 1O—A)
•Inspect water temperature
sensor
•Inspect terminal voltage of
climate control unit (2H, 2L)
1P A/C Refrigerant
pressure switchFan switch at OFF
12•Inspect for continuity or
short circuit (Climate control
unit—refrigerant pressure
switch: 1P—A) (Refrigerant
pressure switch—PCM: B—
1AC (except MZR-CD (RF
Turbo)), 84 (MZR-CD (RF
Turbo)))
•Inspect refrigerant pressure
switch
•Inspect PCM terminal
voltage (1AC (except MZR-
CD (RF Turbo)), 84 (MZR-
CD (RF Turbo)))
(See F1–33 PCM
INSPECTION (4WD) )
(See F2–65 PCM
INSPECTION )
Fan switch at 1st
position, A/C switch ONBelow 1.0•Inspect terminal voltage of
climate control unit (2H, 2L) Terminal Signal Connected to Test condition Voltage (V) Action

CONTROL SYSTEM
U–19
U
1Q Evaporator
temperature
sensor input
signalEvaporator
temperature sensorDepends on temperature
surrounding sensor
See Figure
1•Inspect for continuity
(Climate control unit—
evaporator temperature
sensor: 1Q—B, 1I—A)
•Inspect for short circuit
(Climate control unit—
evaporator temperature
sensor: 1Q—B)
•Inspect evaporator
temperature sensor
•Inspect terminal voltage of
climate control unit (2H, 2L)
1R—— —— —
1S Solar radiation
sensor inputSolar radiation
sensorIncandescent light (60W)
shining on solar
radiation sensor from
distance of approx.
100mm {3.9 in}4.0•Inspect for continuity or
short circuit (Climate control
unit—solar radiation sensor:
1S—B, 1B—A)
•Inspect terminal voltage of
climate control unit (1B)
•Inspect solar radiation
sensor Light to solar radiation
sensor blockBelow 1.0
1T GND Ground Under any condition
Below 1.0•Inspect for continuity
(Climate control unit—
ground: 1T—GND)
•Inspect center panel
1U Potentiometer
signalAir mix actuator Set temperature at MAX
COLD0.6•Inspect for continuity or
short circuit (Climate control
unit—air mix actuator: 1U—
C)
•Inspect air mix actuator
•Inspect terminal voltage of
climate control unit (1B) Set temperature at MAX
HOT
4.3
1V—— —— —
1W Potentiometer
signalAirflow mode
actuatorVENT mode 4.3•Inspect for continuity or
short circuit (Climate control
unit—airflow mode actuator:
1W—C)
•Inspect airflow mode
actuator
•Inspect terminal voltage of
climate control unit (1B) BI-LEVEL mode 3.3
HEAT mode 2.3
HEAT/DEF mode 1.5
DEFROSTER mode
0.6
1X Hazard warning
SW signalHazard warning
switchHazard warning switch is
off
12•Inspect for continuity or
short circuit (Climate control
unit—flasher unit: 1X—H)
•Inspect flasher unit
Hazard warning switch is
on Below 1.0•Inspect terminal voltage of
climate control unit (1T)
•Inspect center panel
2A Panel light control
signalPanel light control
switchHeadlight switch ON and
panel light control switch
at max. illumination
0.2•Inspect for continuity
(Climate control unit— panel
light control switch: 2A—C)
(Panel light control switch—
ground: C—GND)
•Inspect panel light control
switch
Headlight switch ON and
panel light control switch
at min. illumination10.2•Inspect for short circuit
(Climate control unit— panel
light control switch: 2A—C) Terminal Signal Connected to Test condition Voltage (V) Action

U–20
CONTROL SYSTEM
2B TNS signal TNS relay Headlight switch OFF
Below 1.0•Inspect for short circuit
(Climate control unit—TNS
relay: 2B—D)
•Inspect TNS relay
•Inspect headlight switch
Headlight switch ON
12•Inspect for continuity or
short circuit (Climate control
unit—TNS relay: 2B—D)
•Inspect TNS relay
•Inspect headlight switch
2C Motor drive signal Air mix actuator Moving to COLD 12•Inspect for continuity or
short circuit (Climate control
unit—air mix actuator: 2D—
D, 2C—F)
•Inspect air mix actuator Moving to HOT
Below 1.0
2D Motor drive signal Air mix actuator Moving to HOT 12•Inspect for continuity or
short circuit (Climate control
unit—air mix actuator: 2C—
F, 2D—D)
•Inspect air mix actuator Moving to COLD
Below 1.0
2E Motor drive signal Airflow mode
actuatorMoving to DEFROSTER 12•Inspect for continuity or
short circuit (Climate control
unit—airflow mode actuator:
2E—F, 2G—D)
•Inspect airflow mode
actuator Moving to VENT
Below 1.0
2F Backup power
supply ROOM 15 A fuse Under any condition
B+•Inspect for continuity or
short circuit (Climate control
unit—fuse: 2F— ROOM 15
A fuse)
•Inspect ROOM 15 A fuse
2G Motor drive signal Airflow mode
actuatorMoving to VENT 12•Inspect for continuity or
short circuit (Climate control
unit—airflow mode actuator:
2G—D, 2E—F)
•Inspect airflow mode
actuator Moving to DEFROSTER
Below 1.0
2H IG2 A/C 15 A fuse Ignition switch at ON
position
B+•Inspect for continuity or
short circuit (Climate control
unit—fuse: 2H—A/C 15 A
fuse)
•Inspect A/C 15 A fuse
Ignition switch at LOCK
position Below 1.0•Inspect for short circuit
(Climate control unit—fuse:
2H—A/C 15 A fuse)
2I Motor drive signal Air intake actuator Moving to
RECIRCULATE12•Inspect for continuity or
short circuit (Climate control
unit—air intake actuator:
2I—F, 2K—D)
•Inspect air intake actuator Moving to FRESH
Below 1.0
2J—— —— —
2K Motor drive signal Air intake actuator Moving to FRESH 12•Inspect for continuity or
short circuit (Climate control
unit—air intake actuator:
2K—D, 2I—F)
•Inspect air intake actuator Moving to
RECIRCULATE
Below 1.0
2L GND Ground Under any condition
Below 1.0•Inspect for continuity
(Climate control unit—
ground: 2L—GND) Terminal Signal Connected to Test condition Voltage (V) Action

CONTROL SYSTEM
U–21
U
End Of Sie
VOLTAGE (V)
01 2 3 45
TEMPERATURE
°C {°F} -20
{-4}-10
{14}0
{32}10
{50}20
{68}30
{86}40
{104}50
{122} Figure 1 (Evaporator temperature sensor)
°C {°F}
VOLTAGE (V)
0 1 23 4
5
TEMPERATURE -20
{-4}-10
{14}0
{32}10
{50}20
{68}30
{86}40
{104}50
{122} Figure 2 (Ambient temperature sensor)
°C {°F} 0 1 2 3 45
-20
{-4}-10
{14}0
{32}10
{50}20
{68}30
{86}40
{104}50
{122}
TEMPERATURE
VOLTAGE (V)
Figure 3 (Cabin temperature sensor)
°C {°F} 0 12 3 45
VOLTAGE (V)
10
{50}30
{86}50
{122}70
{158}90
{194}
TEMPERATURE Figure 4 (Water temperature sensor)

U–22
ON-BOARD DIAGNOSTIC
FOREWORDA6E857001038201Outline
•When the customer reports a vehicle malfunction, verify the DTC, then diagnose the malfunction according to
following flowchart.
—If a DTC exists, diagnose according to the applicable DTC inspection (See U–22–2 DTC TABLE.)
—If a DTC exists, diagnose according to the applicable symptom troubleshooting (See U–26
TROUBLESHOOTING INDEX.)
Read/clear diagnostic results
•This function allows you to read or clear DTCs in the water heater unit.
DTCs Reading Procedure
1. Perform the necessary vehicle preparation and visual inspection.
2. Connect SST (WDS or equivalent) to the vehicle
DLC-2 16-pin connector located as shown in the
figure.
3. Retrieve DTCs using WDS or equivalent.
KOEO Self Test/Combustion Test
1. Connect the SST (WDS or equivalent) to the
vehicle DLC-2 16-pin connector located as shown
in the figure.
2. Select the “Supplemental Heater Test” in the
“Supplemental Heater Menu” of the “Guided
Diagnosis” function.
3. Perform the KOEO Self Test/Combustion Test.
Note
•If the water heater unit is operating, the
water heater unit will reject the test
command. Perform the DTC reading
procedure after the water heater unit stops
operating.
End Of Sie
ON-BOARD DIAGNOSTIC
Repair the malfunctioning part by following the
DTC inspection, referring to DTC TABLE.Connect the SST (WDS or equivalent).
Perform the KOEO Self Test/Combustion
Test.
Are any DTCs displayed?
Ye s
No Customer arrivesConfirm the malfunction symptom and troubleshoot
the water heater system for the applicable
malfunction, referring to the TROUBLESHOOTING
INDEX.
B6E0740TL01
DLC-2
A6E3970W002
DLC-2
A6E3970W002

ON-BOARD DIAGNOSTIC
U–22–1
U
U–22H EA TER AND A I R C O NDI T ION ER SYST EMS
After Repair Procedure
1. Connect the SST (WDS or equivalent) to the
vehicle DLC-2 16-pin connector located as shown
in the figure.
2. Turn the ignition switch to the ON position.
3. Perform the DTCs reading procedure and record
any DTCs that are retrieved.
4. Clear the DTCs using the SST (WDS or
equivalent).
5. Verify that the customer’s concern has been
resolved.
Lockout Reset
Using the SST (WDS or equivalent)
1. Connect the SST (WDS or equivalent) to the
vehicle DLC-2 16-pin connector located as shown
in the figure.
2. Select “CLR_LOCKOUT” and “LOCKOUT”.
3. Turn “CLR_LOCKOUT” to ON using the
simulation function.
4. Verify that the “LOCKOUT” reading changes to
“Unlocked”.
Not using the SST (WDS or equivalent)
For factory equipped water heater unit
1. Turn the ignition switch to the OFF position.
2. Remove the HEATER 20 A fuse from the main
fuse block for more than 5 seconds.
3. Re-install the HEATER 20 A fuse.
For vehicles with a transmitter or timer
1. Turn the ignition switch to the OFF position.
2. Remove the power supply 20 A fuse from the
heater wiring harness for approx. 3 seconds.
3. Re-install the power supply 20 A fuse.
4. Press and hold down the ON switch of the
transmitter or timer for approx. 3 seconds.
5. Remove the power supply 20 A fuse from the
heater wiring harness for approx. 3 seconds.
6. Re-install the power supply 20 A fuse.
ON-BOARD DIAGNOSTIC
DLC-2
A6E3970W002
DLC-2
A6E3970W002
HEATER 20 A FUSE
MAIN FUSE
BLOCK
B6E0740TL02
WAIT FOR
APPROX. 3
SECONDS
OR
ON
ONWAIT FOR
APPROX. 3
SECONDS WAIT FOR
APPROX. 3
SECONDS
B6E0740TL03

U–22–2
ON-BOARD DIAGNOSTIC
PID/Data Monitor and Record Procedure
1. Connect SST (WDS or equivalent) to the vehicle
DLC-2 16-pin connector located as shown in the
figure.
2. Access and monitor PIDs by WDS or equivalent.
End Of SieDTC TABLEA6E857001038202
* : If a DTC not listed above is detected, there is a water heater malfunction, and the water heater must be
replaced.
End Of SiePID/DATA MONITOR AND RECORDA6E857001038209PID Monitoring Item Table
DLC-2
A6E3970W002
DTC Possible cause Page
B1317 Input voltage high (See U–22–3 DTC B1317)
B1318 Input voltage low (See U–23 DTC B1318)
B1342 Malfunction in water heater unit(See U–23 DTC B1342, B2463,
B2537, B2538, B2547)
B2449 Glow plug circuit short to ground (See U–24 DTC B2449, B2450)
B2450 Glow plug circuit open (See U–24 DTC B2449, B2450)
B2451 Fuel pump circuit short to ground (See U–24 DTC B2451, B2452)
B2452 Fuel pump circuit open (See U–24 DTC B2451, B2452)
B2453 Blower fan circuit short to ground (See U–25 DTC B2453, B2454)
B2454 Blower fan circuit open (See U–25 DTC B2453, B2454)
B2463 Overheat(See U–23 DTC B1342, B2463,
B2537, B2538, B2547)
B2537 Water heater system does not start(See U–23 DTC B1342, B2463,
B2537, B2538, B2547)
B2538 Unstable flame(See U–23 DTC B1342, B2463,
B2537, B2538, B2547)
B2547 Flame prior to operation(See U–23 DTC B1342, B2463,
B2537, B2538, B2547)
B2548 Water heater lockout mode (See U–25 DTC B2548)
PID Name
(Definition)Unit/
ConditionCondition/Specification
(Reference)ActionWater
Heater Unit
terminal
CCNTFFH
(Number of continuous
codes)—•DTC is detected: 1—255
•DTC is not detected: 0Perform inspection
using appropriate
DTC.—
ECT
(Engine coolant temperature)°C°F•ECT 20 °C {68 °F}: 20 °C {68 °F}
•ECT 60 °C {140 °F}: 60 °C {140 °F}——
VPWR_FFH
(Module supply voltage)V•Ignition switch ON: B+Inspect water heater
unit power supply
terminal.A
VPWR_LMT
(Low voltage threshold)V•Ignition switch ON: approx. 9.5 VInspect water heater
unit power supply
terminal.A
FAN
(Fan control)%•Blower fan is not operating: 0 %
•Blower fan is operating: 0—100 %——
GPD
(Glow plug duty cycle)%•Water heater unit is not operating: 0 %
•Water heater unit is operating: 0—100 %——
BLOWRMTR
(Blower motor)On/Off•Blower fan is not operating: Off
•Blower fan is operating: On——

ON-BOARD DIAGNOSTIC
U–22–3
U
Simulation Test Item Table
End Of SieDTC B1317A6E857001038203
Diagnostic procedure
End Of Sie
FP
(Fuel pump)On/Off•Water heater unit is not operating: Off
•Water heater unit is operating: On——
WATER_PMP
(Water pump)On/Off•Water heater unit is not operating: Off
•Water heater unit is operating: On——
GLOW PLUG
(Glow plugs)On/Off•Water heater unit is not operating: Off
•Water heater unit is operating: On——
COMB_FAN
(Combustion air fan)On/Off•Water heater unit is not operating: Off
•Water heater unit is operating: On——
LOCKOUT
(Heater lockout)Lock/
Unlock•Water heater unit is not operating: Lock
•Water heater unit is operating: Unlock——
FS
(Flame sensor)On/Off•Water heater unit is not operating: Off
•Water heater unit is operating: On——
HEATER
(Heater status)Inactive/
Active•Water heater unit is not operating:
Inactive
•Water heater unit is operating: Active——
HEATER_SW
(Heater activation switch)Inactive/
Active•Water heater unit is not operating:
Inactive
•Water heater unit is operating: Active—— PID Name
(Definition)Unit/
ConditionCondition/Specification
(Reference)ActionWater
Heater Unit
terminal
Item Definition OperationWater Heater
Unit terminal
CLR_LOCKOUT Heater lockout mode clearing command On/——
FUEL_PRIMEFuel pump priming command
(The fuel pump is activated for 5 seconds.)On/——
DTC B1317 Input voltage high
DETECTION
CONDITION•Voltage detected at water heater unit terminals A is more than 16 V.
POSSIBLE
CAUSE•Short to power circuit between the generator and PCM
•Generator malfunction
•Battery malfunction
STEP INSPECTION ACTION
1INSPECT BATTERY VOLTAGE
•Measure the battery voltage.
•Is the voltage less than 16 V?Yes Go to the next step.
No Inspect the charging system.
2INSPECT WATER HEATER UNIT
•Clear the DTC.
•Perform the KOEO Self Test. (See U–22 KOEO
Self Test/Combustion Test.)
•Is the same DTC present?Yes Replace the water heater unit.
(See U–15 WATER HEATER UNIT REMOVAL/
INSTALLATION)
No Go to the next step.
3VERIFY AFTER REPAIR PROCEDURE
•Perform the after repair procedure. (See U–22–1
After Repair Procedure.)
•Are any DTCs present?Yes Go to the applicable DTC troubleshooting.
No Troubleshooting completed.
A C E
B
D F WATER HEATER UNIT CONNECTOR