2002 LAND ROVER DISCOVERY oil

MANUAL GEARBOX - R380
37-34 OVERHAUL
Reassembly
1.Clean input shaft and bearing/oil seal recess in
front cover.
2.Lubricate a new input shaft oil seal with
gearbox oil.
3.Fit oil seal using a suitable mandrel.
4.Using a press and a suitable mandrel, fit
bearing outer track in front cover.
5.Using a press and a suitable mandrel, fit pilot
bearing outer track to input shaft.
6.Using tool LRT-37-043, LRT-37–043/2 and
LRT-99-002, fit new taper bearing to input
shaft.7.Using tool LRT-99-002 and a suitable mandrel,
press new pilot bearing onto output shaft.
8.Position input shaft to gearbox case.
9.With assistance, fit output shaft and layshaft
assembly into gearbox case.
10.Fit reverse idler gear shaft.

+ MANUAL GEARBOX - R380,
OVERHAUL, Shaft - reverse idler.
11.Fit gearbox front cover.

+ MANUAL GEARBOX - R380,
OVERHAUL, Cover - front.

MANUAL GEARBOX - R380
OVERHAUL 37-35
Extension - gearbox rear
$% 37.12.01
Disassembly
1.Remove 4 bolts and remove gear selector
housing.
2.Using tools LRT-37-009, LRT-37-001/2 and
LRT-37-010 , remove output shaft oil seal
collar.3.Remove bolt securing interlock spool retainer
and discard 'O' ring.
4.Noting fitted position of 2 longest bolts, remove
10 bolts securing extension housing to
gearbox.
5.Remove extension housing from gearbox
centre plate.

MANUAL GEARBOX - R380
37-36 OVERHAUL
6.Fit 2 off 8x35 mm slave bolts to secure centre
plate to gearbox casing.
7.Remove 3 Torx screws, remove oil pump and
discard 'O' ring.
8.Drift out layshaft support bearing.
9.Remove and discard output shaft rear oil seal.
10.Remove oil pick-up pipe.
11.Drift out output shaft support bearing and oil
pick-up ring.
12.Remove reverse inhibitor shaft, cam and
spring. 13.Remove 2 bolts and remove gate plate.
14.Remove reverse light switch and discard
sealing washer.
15.Remove 2 bolts, remove oil cooler by-pass and
discard 'O' rings.
Reassembly
1.Clean extension housing and mating faces.
2.Clean oil cooler by-pass.
3.Using new 'O' rings, fit oil cooler by-pass and
tighten bolts to 15 Nm (11 lbf.ft).
4.Using new sealing washer, fit reverse light
switch and tighten to 24 Nm (17 lbf.ft).
5.Fit reverse inhibitor spring and cam.
6.Clean threads of reverse inhibitor shaft and
gate plate bolts.
7.Apply Loctite 290 to threads of reverse inhibitor
shaft, fit and tighten shaft.
8.Apply Loctite 290 to threads of gate plate bolts.
9.Position gate plate and tighten bolts to 15 Nm
(11 lbf.ft).
10.Fit output shaft support bearing and oil pick-up
ring. Align tag with centre of drain slot.
11.Fit layshaft support bearing.
12.Fit new output shaft oil seal using tool LRT-37-
014.

MANUAL GEARBOX - R380
OVERHAUL 37-37
13.Fit oil pick-up pipe with the off-set uppermost.
14.Lubricate oil pump recess with gearbox oil.
15.Lubricate a new 'O' ring with gearbox oil and fit
to oil pump.
16.Locate oil pump in extension housing with word
'TOP' towards top of housing.
17.Align oil pump fixing screw holes and tap pump
lightly around edges until it is fully in recess.
Do not attempt to pull pump into recess
using fixing screws.
18.Fit Torx screws and tighten to 6 Nm (4.5 lbf.ft).
19.Remove 2 slave bolts securing centre plate to
gearbox casing.
20.Apply sealant, Part No. STC 3254 to gearbox
casing face.
21.Position extension housing, align oil pump drive
with layshaft.
22.Clean extension housing bolt threads.
23.Apply Loctite 290 to threads of extension
housing bolts, fit bolts ensuring 2 longest bolts
are in their original positions and tighten by
diagonal selection to 25 Nm (18 lbf.ft).
24.Using new 'O' ring, fit interlock spool retainer
and tighten bolt to 8 Nm (6 lbf.ft).
25.Using tool LRT-37-015 and LRT-37-021, fit oil
seal collar.
26.Clean gear selector selector housing and
mating face.
27.Apply sealant, Part No. STC 3254 to gear
selector housing face.
28.Position gear selector housing and tighten
bolts to 25 Nm (18 lbf.ft).
Pump - gearbox oil
$% 37.12.47
Disassembly
1.Remove gearbox extension.

+ MANUAL GEARBOX - R380,
OVERHAUL, Extension - gearbox rear.
2.Remove 3 Torx screws, remove oil pump and
discard 'O' ring.
Reassembly
1.Clean oil pump recess in extension housing,
ensure screw holes are clean and dry.
2.Lubricate oil pump recess in housing with
gearbox oil.
3.Lubricate a new 'O' ring with gearbox oil and fit
to oil pump.
4.Locate oil pump in extension housing with word
'TOP' towards top of housing.
5.Align fixing screw holes and tap pump lightly
around edges until pump is fully in housing. Do
not pull pump into housing by tightening
screws.
6.Fit Torx screws and tighten to 6 Nm (4.5 lbf.ft).
7.Fit gearbox extension.

+ MANUAL GEARBOX - R380,
OVERHAUL, Extension - gearbox rear.

MANUAL GEARBOX - R380
37-38 OVERHAUL
Filter - gearbox oil
$% 37.12.38
Disassembly
1.Remove gearbox extension.

+ MANUAL GEARBOX - R380,
OVERHAUL, Extension - gearbox rear.
2.Remove oil filter from gearbox.
Reassembly
1.Clean filter recess in gearbox.
2.Fit filter.
3.Fit gearbox extension.

+ MANUAL GEARBOX - R380,
OVERHAUL, Extension - gearbox rear.
Gear - 5th gear set
$% 37.20.36
Disassembly
1.Remove 5th gear - layshaft.

+ MANUAL GEARBOX - R380,
OVERHAUL, 5th gear - layshaft.
2.Using tool LRT-37-001/2, LRT-37-009 and
LRT-37-010, remove output shaft support
bearing track.
3.Remove 5th gear and baulk ring from output
shaft.

MANUAL GEARBOX - R380
37-42 OVERHAUL
Bearing - layshaft rear support
$% 37.20.58
Disassembly
1.Remove extension housing.

+ MANUAL GEARBOX - R380,
OVERHAUL, Extension - gearbox rear.
2.Remove 3 Torx screws, remove oil pump and
discard 'O' ring.
3.Drift out layshaft support bearing.
4.Using a suitable two legged puller remove 5th
gear layshaft support bearing track from end of
layshaft. Reassembly
1.Clean layshaft and bearing recess in extension
housing.
2.Fit layshaft support bearing.
3.Clean oil pump recess in extension housing,
ensure screw holes are clean and dry.
4.Lubricate oil pump recess in housing with
gearbox oil.
5.Lubricate a new 'O' ring with gearbox oil and fit
to oil pump.
6.Locate oil pump in extension housing with word
'TOP' towards top of housing.
7.Align fixing screw holes and tap pump lightly
around edges until pump is fully in housing. Do
not pull pump into housing by tightening
screws.
8.Fit Torx screws and tighten to 6 Nm (4.5 lbf.ft).
9.Apply a small amount of heat and fit support
bearing track to layshaft.
10.Fit extension housing.

+ MANUAL GEARBOX - R380,
OVERHAUL, Extension - gearbox rear.

MANUAL GEARBOX - R380
OVERHAUL 37-43
Bearing - output shaft rear support
$% 37.20.55
Disassembly
1.Remove extension housing.

+ MANUAL GEARBOX - R380,
OVERHAUL, Extension - gearbox rear.
2.Using tool LRT-37-001/2, LRT-37-009 and
LRT-37-010, remove output shaft support
bearing track.
3.Remove output shaft rear oil seal. 4.Remove output shaft support bearing and oil
pick-up ring.
Reassembly
1.Clean output shaft and bearing recess in
extension housing.
2.Fit output shaft support bearing and oil pick-up
ring. (Align tag with centre of drain slot).
3.Fit new output shaft oil seal using LRT-37-014.

MANUAL GEARBOX - R380
37-44 OVERHAUL
4.Using tool LRT-37-015 and LRT-37-021, fit
support bearing track to output shaft.
5.Fit extension housing.

+ MANUAL GEARBOX - R380,
OVERHAUL, Extension - gearbox rear.
Shaft - reverse idler
$% 37.20.13
Disassembly
1.Remove 5th / reverse gear synchroniser.

+ MANUAL GEARBOX - R380,
OVERHAUL, Synchronizer assembly - 5th/
reverse.
2.Remove reverse gear complete with needle
roller bearing and collar noting selective spacer
between collar and centre plate bearing.
3.Remove layshaft reverse gear noting oil groove
faces centre plate bearing.
4.Remove detent screw from centre plate and
collect upper detent ball and spring.