2002 LAND ROVER DISCOVERY oil type

GENERAL DATA
04-5
Idle speed:

All loads off 660 ± 50 rev/min

Base idle speed Non-adjustable

Idle air control (IAC) valve position Checked via TestBook
CO at idle:

Catalyst vehicles 0.5 %

Non-catalyst vehicles 0.5 - 1.0 %
Valve timing
Inlet valves:

Opens 28° BTDC

Closes 77° ABDC
Exhaust valves:

Opens 66° BBDC

Closes 39° ATDC
Fuel grade:

High compression catalyst vehicles 95 RON minimum unleaded

Low compression catalyst vehicles 91 RON minimum unleaded

Non-catalyst vehicles 97 RON leaded
Lubrication
Type Wet sump, pressure fed
Pump type Crankshaft driven eccentric rotor
Oil filter Disposable canister with full flow by-pass
Pressure at idle - minimum 0.7 bar (10 lbf.in
2)
Pressure at 2000 rev/min (hot) 3.4 bar (50 lbf.in
2)
Relief valve opening pressure 3.4 bar (50 lbf.in
2)
Low oil pressure switch opening pressure 0.24-0.41 bar (3.5-6.0 lbf.in
2)
Crankshaft
Main journal diameter 63.487 - 63.500 mm (2.4995 - 2.520 in)
Crankpin journal diameter 55.500 - 55.513 mm (2.20 - 2.22 in)
End float 0.08 - 0.26 mm (0.003 - 0.010 in)
Maximum ovality 0.040 mm (0.002 in)
Main bearings
Quantity 5
Material Glacier Vandervell / AS 15
Diametrical clearance 0.015 - 0.016 mm (0.00059 - 0.00063 in)
Connecting Rods
Type Horizontally split big-end, plain small end
Distance between centres 155.120 - 155.220 mm (6.1071 - 6.1110 in)

GENERAL DATA
04-6
Big-end bearings
Quantity 8
Material Glacier Vandervell GPL 2120/AS 124A
Diametrical clearance 0.015 - 0.016 mm (0.00059 - 0.00063 in)
End float 0.15 - 0.35 mm (0.0006 - 0.0138 in)
Gudgeon pins
Diameter 23.995 - 24.000 mm (0.9447 - 0.9449 in)
Clearance in piston 0.006 - 0.015 mm (0.00024 - 0.00059 in)
Fit in connecting rod Press fit
Length 60.00 - 60.50 mm (2.362 - 2.382 in)
Pistons
Type Solid skirt, elliptical open end with offset gudgeon pin
Material Aluminium AE413P
Clearance in cylinder bore.
Measured 10 mm (0.4 in) from bottom of skirt, 90° to
gudgeon pin.0.022 - 0.067 mm (0.0009 - 0.0026 in)
Diameter - Grade A 93.970 - 93.985 mm (3.6996 - 3.7002 in)
Diameter - Grade B 93.986 - 94.001 mm (3.7002 - 3.7008 in)
Piston rings
Type: 2 compression, 1 oil control

Top compression ring Barrel faced nitrided steel

2nd compression ring Tapered spherical

Oil control ring 3 piece AE Conoform
Piston ring fitted gap in cylinder bore:

Top compression ring gap 0.3 - 0.5 mm (0.012 - 0.020 in)

2nd compression ring gap 0.40 - 0.65 mm (0.016 - 0.026 in)

Oil control ring gap 0.38 - 1.40 mm (0.015 - 0.055 in)
Piston ring width:

Top compression ring width 1.21 - 1.23 mm (0.0476 - 0.0484 in)

2nd compression ring width 1.478 - 1.490 mm (0.0582 - 0.0587 in)

Oil control ring width 3.00 mm (0.1181 in)
Piston ring to groove clearance:

1st and 2nd compression rings 0.05 - 0.10 mm (0.002 - 0.004 in)
Camshaft
Bearings 5
Drive Chain, 9.52 mm (0.3748 in) pitch x 54 pitches
End float 0.075 - 0.25 mm (0.002 - 0.010 in)
Tappets
Type Hydraulic self adjusting
Outside diameter 21.386 - 21.407 mm (0.8420 - 0.8427 in)

GENERAL DATA
04-15
Suspension
* Measurement taken with vehicle at unladen weight.
Type - Front Beam axle with coil springs, longitudinal radius arms,
Panhard rod, twin tube dampers and either anti-roll
bar or active cornering enhancement (ACE)
Nominal height from hub centre to wheel arch (not liner)* 500 ± 15 mm (19.7 ± 0.6 in)
Front road spring colour codes:

V8 LHS Pink/orange

V8 RHS - LHD Pink/orange

V8 RHS - RHD White/purple

Td5 LHS White/purple

Td5 RHS - LHD White/purple

Td5 RHS - RHD White/purple
Rear road spring colour codes:
5 seat, LHS Purple
5 seat, RHS - LHD Purple
5 seat, RHS - RHD Purple/purple
7 seat, LHS - LHD Grey/blue
7 seat, LHS - RHD Grey/green
7 seat, RHS - LHD Grey/blue
7 seat, RHS - RHD Grey/white
Bump stop height (top of bump stop to axle bracket) 44.5 mm (1.75 in)
Anti-roll bar diameter - front

With ACE fitted 35 mm (1.38 in)

Without ACE 30 mm (1.18 in)
Type - Rear Beam axle with coil or air springs, longitudinal radius
arms, Watts linkage, twin tube dampers and either
anti-roll bar or active cornering enhancement (ACE)
Nominal height from hub centre to wheel arch (not liner):*

Coil spring 483 ± 15 mm (19.0 ± 0.6 in)

Air spring 473 ± 15 mm (18.6 ± 0.6 in)
Road spring colour code Purple (all models)
Bump stop height (top of bump stop to axle bracket):

Coil spring 71.5 mm (2.8 in)

Air spring 61.5 mm (2.4 in)
Anti-roll bar diameter - rear

With ACE fitted 35 mm (1.38 in)

Without ACE - SLS fitted 29 mm (1.14 in)

Without ACE - SLS not fitted 5 seats = 19 mm (0.75 in)
7 seats = 16 mm (0.63 in)

GENERAL DATA
04-17
Air conditioning
Electrical - Td5
Electrical - V8
Type CFC free, sealed closed loop
Compressor:

Displacement 177.7 cm
3/rev (10.84 in3/rev)

Relief valve operating pressure 34.3 to 41.4 bar (497 to 600 lbf.in
2)

Refrigerant oil quantity 180ml (6.3 fl.oz)
Dual pressure switch operating pressures (nominal):

Low pressure switch Opens 2.0 bar (29.0 lbf.in
2), pressure decreasing

Low pressure switch Closes 2.3 bar (33.4 lbf.in
2), pressure increasing

High pressure switch Opens 32 bar (464 lbf.in
2), pressure increasing

High pressure switch Closes 26 bar (377 lbf.in
2), pressure decreasing
System 12 volt, negative earth
Battery:

Type Delco Freedom

Capacity 110 amp hour
Alternator:

Type Nippon Denso

Maximum output 120 amp
Starter motor:

Type Nippon Denso

Power 2 kW
System 12 volt, negative earth
Battery:

Type Delco Freedom

Capacity 72 amp hour
Alternator:

Type Bosch NC65/130

Maximum output 130 amp
Starter motor

Type Nippon Denso

Power 1.8 kW

LIFTING AND TOWING
08-2
Reverse procedure when removing vehicle from
stands.
Hydraulic ramps
Use only a 'drive on' type ramp which supports a
vehicle by it's own road wheels. If a 'wheel free'
condition is required, use a 'drive on' ramp
incorporating a 'wheel free' system that supports
under axle casings. Alternatively, place vehicle on a
firm, flat floor and support on axle stands.
TOWING
Towing
The vehicle has permanent four wheel drive. The
following towing instructions must be adhered
to:
Towing on 4 wheels with driver
Turn ignition key to position '1' to release steering
lock.
Select neutral in main gearbox and transfer gearbox.
Secure tow rope, chain or cable to towing eye.
Release the handbrake.
The brake servo and power assisted steering
system will not be functional without the engine
running. Greater pedal pressure will be required
to apply the brakes, the steering system will
require greater effort to turn the front road
wheels. The vehicle tow connection should be
used only in normal road conditions, 'snatch'
recovery should be avoided.Suspended tow
To prevent vehicle damage, front or rear
propeller shaft MUST BE removed, dependent
upon which axle is being trailed.
Mark propeller shaft drive flanges at transfer box and
axles with identification lines to enable the propeller
shaft to be refitted in its original position.
Remove the propeller shaft fixings, remove the shaft
from the vehicle.
If the front axle is to be trailed turn ignition key to
position '1' to release steering lock.
The steering wheel and/or linkage must be
secured in a straight ahead position. DO NOT use
the steering lock mechanism for this purpose.
Towing eyes
The towing eyes at the front and rear of the vehicle
are designed for vehicle recovery purposes only and
must NOT be used to tow a trailer or caravan.
Front:A single towing eye, set behind a removable
panel in the front spoiler. DO NOT use the front
lashing rings for towing.

CAPACITIES, FLUIDS AND LUBRICANTS
09-2
Refrigerant - A/C system
Fluids
Anti-freeze
Use Havoline Extended Life Coolant (XLC), or any
ethylene glycol based anti-freeze (containing no
methanol) with only Organic Acid Technology
corrosion inhibitors, to protect the cooling system
CAUTION: No other anti-freeze should be used
with Havoline Extended Life Coolant.
The cooling system should be drained, flushed and
refilled with the correct amount of anti-freeze solution
at the intervals given on the Service Maintenance
Check Sheet.
After filling with anti-freeze solution, attach a warning
label to a prominent position on the vehicle stating
the type of anti-freeze contained in the cooling
system to ensure that the correct type is used for
topping-up.
Brake/Clutch fluid
Use only DOT 4 brake fluid.
PAS/ACE fluid
Use Texaco cold climate power assisted steering
fluid 14315.
Air conditioning
Use only refrigerant R134a.
Refrigerant oil
Use only NipponDenso ND-oil 8 or Unipart ND-oil 8.
Refrigerant oil absorbs water and must not be stored
for long periods. Do not pour unused oil back into the
container.
NOTE: The total quantity of refrigerant oil in the
system is 180 ml.
CAUTION: Do not use any other type of
refrigerant oil.

Refill3.4 pt

Fill from dry 3.6 pt
Cooling system - V8 Engine:

Refill24.2 pt

Fill from dry 26.2 ptComponent US Units

Front A/C 700 ± 25 g

Front/rear A/C 900 ± 25 g

MAINTENANCE
PROCEDURES 10-15
Centrifuge rotor – diesel engine
Replace
1.Replace centrifuge rotor.

+ ENGINE - Td5, REPAIRS, Rotor -
centrifuge.
Engine oil filter - diesel engine
Replace
1.Replace oil filter.

+ ENGINE - Td5, REPAIRS, Filter - oil.
Engine oil filter – V8 engine
WARNING: Avoid excessive skin contact with
used engine oil. Used engine oil contains
potentially harmful contaminants which may
cause skin cancer or other serious skin
disorders.
Replace
1.Disconnect battery.
2.Position suitable container beneath oil filter.
3.Using a strap type filter wrench, remove filter
element, discard element.
4.Smear sealing ring of replacement filter
element with engine oil.
5.Fit filter element, tighten two thirds of a turn by
hand or to 17 Nm (13 lbf.ft).
6.Top-up engine with recommended grade of oil
to correct mark on dipstick.

+ CAPACITIES, FLUIDS AND
LUBRICANTS, Lubrication.
7.Connect battery.
8.Run engine and check for oil leaks from filter.
9.Stop engine, wait for oil to return to sump.
10.Re-check oil level and top-up if necessary.

ENGINE - TD5
12-1-16 DESCRIPTION AND OPERATION
Oil filters
The Td5 engine features two types of oil filter; the main filter is a standard disposable cartridge-type full-flow oil filter
which is augmented with a by-pass centrifuge filter used to filter out particulate matter having a diameter smaller than
15 micron but greater than 3 micron.
1Centre spindle
2Spindle oil holes (2 off)
3Centrifuge filter housing
4Centrifuge filter drain pipe
5Port – centrifuge filter drain pipe to sump6Filter rotor
7Internal seal
8Cover
9Cover bolts (2 off)
The centrifuge filter is located on the left hand side of the engine block by the exhaust manifold and is housed in a pot
which is bolted to the oil cooler housing by means of three bolts. The pot contains a rotor located on a central spindle
which spins at up to 15,000 revs/min. when oil is flowing through the unit under pressure. The rotor contains two fine
holes drilled at obtuse angles which cause the rotor to spin about the centre spindle when high pressure oil is passing
through it. The inner surface of the rotor captures carbon deposits and small particulate matter as it is thrown outwards
under centrifugal force to form a sludge on the inner walls of the rotor. The unit is able to trap very fine impurities that
build up in the oil that would be too small to filter using the normal paper-element type full-flow filters alone.
Approximately 10% of the total oil flow enters the centrifuge pot through a side port in the pot casting which is mated
to an outlet port at the lower side of the oil cooler housing. A rubber O-ring sits in a recess around the oil cooler port
which seals the faces between the centrifuge pot and oil cooler port, and it must be replaced every time the centrifuge
assembly is removed. Oil leaves the centrifuge pot through a drain tube which is attached to the base of the pot by
means of two fixing screws. The lower end of the drain tube returns oil to the sump and is fixed to the sump by means
of two screws. Gaskets are included at the port interfaces between the oil drain tube and the centrifuge pot, and the
oil drain tube and sump return port; these gaskets must be replaced every time the oil drain tube is removed.
The centrifuge cover is fixed to the pot by two screws and is sealed by an 'O'-ring.