2002 ISUZU AXIOM roof

8J±4EXTERIOR/INTERIOR TRIM
7. Remove the CD changer.

Remove the four fixing bolts and the connector.Installation
To install, follow the removal steps in the reverse order.
Front Door Trim Panel
Front Door Trim Panel and Associated Parts
635R200012
Legend
(1) Glass
(2) Glass Run
(3) Door Mirror Assembly
(4) Door Mirror Cover
(5) Tweeter
(6) Speaker Spacer
(7) Speaker Assembly
(8) Inner Waist Seal
(9) Door Trim Panel
(10) Power Window Switch
(11) Inside Lock Bracket(12) Inside Handle
(13) Pull Box
(14) Courtesy Light
(15) Pull Box Bracket
(16) Waterproof Sheet
(17) Front Door Panel
(18) Door Lock Assembly
(19) Door Lock Cylinder
(20) Outside Handle
(21) Power Window Regulator
(22) Outer Waist Seal

8J±6EXTERIOR/INTERIOR TRIM
Rear Door Trim Panel
Rear Door Trim Panel and Associated Parts
655R200009
Legend
(1) Glass Run
(2) Glass
(3) Division Bar
(4) Fix Window Glass
(5) Power Window Regulator
(6) Outside Handle
(7) Door Lock Assembly
(8) Pull Box Bracket
(9) Speaker Spacer
(10) Speaker(11) Pull Box
(12) Door Trim Panel
(13) Courtesy Light
(14) Power Window Switch
(15) Inside Handle
(16) Inside Lock Bracket
(17) Inner Waist Seal
(18) Tweeter
(19) Waterproof Sheet
(20) Outer Waist Seal
(21) Rear Door Panel

EXTERIOR/INTERIOR TRIM8J±9
Interior Trim Panels
Interior Trim Panels and Associated Parts
643R200003
Legend
(1) Assist Grip (Front & Rear)
(2) Door Finisher (Front & Rear)
(3) Upper Quarter Pillar Trim Cover
(4) Upper Rear Pillar Trim Cover
(5) Rear Roof Trim Cover
(6) Tailgate Weather Strip
(7) Multi Hook(8) Rear End Floor Trim Cover
(9) Lower Quarter Trim Cover
(10) Sill Plate (Front & Rear)
(11) Lower Center Pillar Trim Cover
(12) Upper Center Pillar Trim Cover
(13) Dash Side Trim Cover
(14) Front Pillar Trim Cover
Removal
1. Disconnect the battery ground cable.
2. Remove the sill plates (Front & Rear).
3. Remove the dash side trim cover.
4. Remove the lower center pillar trim cover.

Remove the lower anchor bolt cover and lower
anchor bolt from the front seat belt.

Pry the trim cover with the clips from the body panel.
5. Remove the door finishers (Front & Rear).

8J±10EXTERIOR/INTERIOR TRIM
6. Remove the upper center pillar trim cover.

Remove the cover (1) and screw.

Remove the shoulder anchor cap (2) and upper
anchor bolt (3) from the front seat belt.

Pry the trim cover with the clip from the body panel.
760R200006
7. Remove the front pillar trim cover.

Ply the trim cover with the clips from the body panel.
8. Remove the tailgate weather strip.
9. Remove the rear end floor trim cover.

Remove the four screw cover and nine fixing
screws.
10. Remove the rear roof trim cover.

Pry the trim cover with the clips from the body panel.
11. Remove the tonneau cover assembly (1).
643R200001
12. Remove the multi hooks.

While raising the notch of the hook with the
screwdriver, pull out the hook by turning 180
.
643R200004
13. Remove the lower quarter trim cover (1).

Remove the lower anchor bolt cover (4) and the
lower anchor bolt (3) from the rear seat belt.

Pull the trim cover at the five clip positions (2).

Disconnect the accessory socket connectors (LH
side).
643R200006
14. Remove the upper quarter pillar trim cover (1).

Remove the cover and screw, pull the trim cover at
the two clip positions (2).

Remove the shoulder anchor cap (4) and upper
anchor bolt (3) from the rear seat belt.

8J±12EXTERIOR/INTERIOR TRIM
Headlining
Parts Location
666R200001
Legend
(1) Interior Trim Panels
(2) Headlining (Without Sunroof)
(3) Clip
(4) Luggage Room Light
(5) Assist Grip
(6) Headlinng (With Sun Roof)(7) Sunroof Finisher (With Sunroof)
(8) Overhead Console/Sunroof Switch (With
Sunroof)
(9) Dome Light
(10) Overhead Console (Without Sunroof)
(11) Sunvisors
(12) Sunvisor Holder
Removal
1. Disconnect the battery ground cable.
2. Remove the interior trim panels.

Refer to
Interior Trim Panels in this section.
3. Remove the dome light.

Remove the dome light lens and the fixing screws.
Disconnect the dome light connectors.

EXTERIOR/INTERIOR TRIM8J±13
4. Remove the luggage room light.

Remove the luggage room light lens (1) and the
fixing screw.

Disconnect the luggage room light connector.
825R200030
5. Remove the overhead console/sunroof switch (With
sunroof).

Refer to
Overhead Console in this section.
6. Remove the overhead console (without sunroof).
7. Remove the sunvisors.

Remove the fixing screws and pull out the sunvisor
holder (1) to remove it.

Disconnect the vanity mirror illumination connector.
743R200003
8. Remove the sunroof finisher (With sunroof).
9. Remove the headlining.

Remove the four headlining fixing clips.
Installation
To install, follow the removal steps in the reverse order,
noting the following points.
1. Install the headlining so that the fixing clips will not
come off.
2. To install the sunroof finisher (1), first fit it in at one
place with the headlining (3) close to the sunroof
frame (2), then install the entire finisher tightly by
hitting it with a plastic hammer, not allowing it to move
up.
665RW003

8J±14EXTERIOR/INTERIOR TRIM
Overhead Console
Parts Location (W/O Sunroof)
743R200005
Legend
(1) Overhead Console Bracket
(2) Harness Connector
(3) Head Lining(4) Room Mirror
(5) Overhead Console Assembly
(6) Front Door Finisher
(7) Front Assist Grip
Removal
1. Disconnect the battery ground cable.
2. Remove the overhead console assembly.

Open the lid and remove the two screws.

Disconnect the harness connector.
3. Remove the sunvisor and sunvisor holder. (right and
left)
4. Remove the front assist grip. (right and left)
5. Remove the front piller trim cover.6. Remove the front door finisher.

Remove the upper side of door finisher.
7. Remove the interior mirror.

Refer to
Interior Mirror in this section.
8. Remove the overhead console bracket.

Remove the two screws.
Installation
To install, follow the removal steps in the reverse order.

EXTERIOR/INTERIOR TRIM8J±15
Parts Location (W/ Sunroof)
743R200004
Legend
(1) Sunroof Weatherstrip
(2) Overhead Console Bracket(3) Head Lining
(4) Overhead Console
(5) Clip Position
Removal
1. Disconnect the battery ground cable.
2. Remove the overhead console.

Open the lid and remove the two screws.

Pull the over head console at the two clip positions.

Disconnect the harness connectors.
3. Remove the head lining.

Refer to
Head Lining in this section.
4. Remove the overhead console bracket.

Remove the five fixing screws.
Installation
To install, follow the removal steps in the reverse order.