2002 ISUZU AXIOM key

5A±46BRAKE CONTROL SYSTEM
Chart B-18 FR Speed Sensor Open or Shorted (DTC 52 (Flash out) / C0221 (Serial
communications))
StepActionYe sNo
11. Turn the key off.
2. Disconnect coil integrated module connector.
3. Measure the resistance between coil integrated module
connector (C-6) terminals 3 and 11.
Is the resistance between 2.0k and 2.8k ohms?Check for faults
in harness
between speed
sensor and coil
integrated
module.
Fault found:
Repair, and
perform system
self-check.
No fault found:
Replace coil
integrated
module.
Go to
Step 3Go to Step 2
2Measure the FR speed sensor resistance at the sensor
connector.
Is the resistance between 2.0k and 2.8k ohms?Repair harness
abnormality
between sensors
and coil
integrated
module.
Go to
Step 3
Replace sensor.
Go to
Step 3
31. Reconnect all components, ensure all components are
properly mounted.
2. Clear diagnostic trouble code.
Was this step finished?
Repeat the ªBasic
diagnostic flow
chartº
Go to Step 3

5A±47
BRAKE CONTROL SYSTEM
Chart B-19 Rear Speed Sensor Open or Shorted (DTC 53 (Flash out) / C0235 (Serial
communications))
StepActionYe sNo
11. Turn the key off.
2. Disconnect coil integrated module connector.
3. Measure the resistance between coil integrated module
connector (C-6) terminals 4 and 12.
Is the resistance between 1.0k and 1.7k ohms?Check for faults
in harness
between speed
sensor and coil
integrated
module.
Fault found:
Repair, and
perform system
self-check.
No fault found:
Replace EHCU.
Go to
Step 3Go to Step 2
2Measure the Rear speed sensor resistance at the sensor
connector.
Is the resistance between 1.0k and 1.7k ohms?Repair harness
abnormality
between sensors
and coil
integrated
module.
Go to
Step 3
Replace sensor.
Go to
Step 3
31. Reconnect all components, ensure all components are
properly mounted.
2. Clear diagnostic trouble code.
Was this step finished?
Repeat the ªBasic
diagnostic flow
chartº
Go to Step 3

5A±48BRAKE CONTROL SYSTEM
Chart B-20 FL Speed Sensor Missing Signal (DTC 61 (Flash out) / C0226, C0227 (Serial
communications))
StepActionYe sNo
11. Turn the key off.
2. Disconnect coil integrated module connector.
3. Measure the FL speed sensor resistance between coil
integrated module connector (C-6) terminals 2 and 10.
Is the resistance between 2.0k and 2.8k ohms?
Go to Step 2Go to Step 3
2Is there play sensor/sensor rotor?Repair.
Go to
Step 6Go to Step 4
3Measure the FL speed sensor resistance at the sensor connector.
Is the resistance between 2.0k and 2.8k ohms?Repair harness
abnormality
between sensors
and coil
integrated
module.
Go to
Step 6
Replace sensor.
Go to
Step 6
4Damage and powdered iron sticking to sensor/sensor ring?Repair.
Go to
Step 6Go to Step 5
5Is sensor output normal? (Chart C-1-1 or TC-1)Check for faults
in harness
between speed
sensor and coil
integrated
module.
Fault found:
repair, and
perform system
self-check.
No fault found:
replace EHCU.
Go to
Step 6
Replace sensor.
Go to
Step 6
61. Reconnect all components, ensure all components are
properly mounted.
2. Clear diagnostic trouble code.
Was this step finished?
Repeat the ªBasic
diagnostic flow
chartº
Go to Step 6
NOTE: Even after repairing the faulty part the warning
light (W/L) does not go out if the vehicle is at a stop. Turn
the ignition switch to the ON position and drive the vehicle
at 12 km/h (8 mph) or higher to make sure that the
warning light goes out.

5A±49
BRAKE CONTROL SYSTEM
Chart B-21 FR Speed Sensor Missing Signal (DTC 62 (Flash out) / C0222, C0223 (Serial
communications))
StepActionYe sNo
11. Turn the key off.
2. Disconnect coil integrated module connector.
3. Measure the FR speed sensor resistance between coil
integrated module connector (C-6) terminals 3 and 11.
Is the resistance between 2.0k and 2.8k ohms?
Go to Step 2Go to Step 3
2Is there play sensor/sensor rotor?Repair.
Go to
Step 6Go to Step 4
3Measure the FR speed sensor resistance at the sensor
connector.
Is the resistance between 2.0k and 2.8k ohms?Repair harness
abnormality
between sensors
and coil
integrated
module.
Go to
Step 6
Replace sensor.
Go to
Step 6
4Damage and powered iron sticking to sensor/sensor ring?Repair.
Go to
Step 6Go to Step 5
5Is sensor output normal? (Chart C-1-2 or TC-1)Check for faults
in harness
between speed
sensor and coil
integrated
module.
Fault found:
repair, and
perform system
self-check.
No fault found:
replace EHCU.
Go to
Step 6
Replace sensor.
Go to
Step 6
61. Reconnect all components, ensure all components are
properly mounted.
2. Clear diagnostic trouble code.
Was this step finished?
Repeat the ªBasic
diagnostic flow
chartº
Go to Step 6
NOTE: Even after repairing the faulty part the warning
light (W/L) does not go out if the vehicle is at a stop. Turn
the ignition switch to the ON position and drive the vehicle
at 12 km/h (8 mph) or higher to make sure that the
warning light goes out.

5A±50BRAKE CONTROL SYSTEM
Chart B-22 Rear Speed Sensor Missing Signal (DTC 63 (Flash out) / C0236, C0237 (Serial
communications))
StepActionYe sNo
11. Turn the key off.
2. Disconnect coil integrated module connector.
3. Measure the Rear speed sensor resistance between coil
integrated module connector (C-6) terminals 4 and 12.
Is the resistance between 1.0k and 1.7k ohms?
Go to Step 2Go to Step 3
2Is there play sensor/sensor rotor?Repair.
Go to
Step 6Go to Step 4
3Measure the rear speed sensor resistance at the sensor
connector.
Is the resistance between 1.0k and 1.7k ohms?Repair harness
abnormality
between sensors
and coil
integrated
module.
Go to
Step 6
Replace sensor.
Go to
Step 6
4Damage and powered iron sticking to sensor/sensor ring?Repair.
Go to
Step 6Go to Step 5
5Is sensor output normal? (Chart C-1-3 or TC-1)Check for faults
in harness
between speed
sensor and coil
integrated
module.
Fault found:
repair, and
perform system
self-check.
No fault found:
replace EHCU.
Go to
Step 6
Replace sensor.
Go to
Step 6
61. Reconnect all components, ensure all components are
properly mounted.
2. Clear diagnostic trouble code.
Was this step finished?
Repeat the ªBasic
diagnostic flow
chartº
Go to Step 6
NOTE: Even after repairing the faulty part the warning
light (W/L) does not go out if the vehicle is at a stop. Turn
the ignition switch to the ON position and drive the vehicle
at 12 km/h (8 mph) or higher to make sure that the
warning light goes out.

5A±51
BRAKE CONTROL SYSTEM
Chart B-23 Simultaneous Drop-out of Front Speed Sensor Signal (DTC 64 (Flash out) /
C0229 (Serial communications))
StepActionYe sNo
11. Turn the key off.
2. Disconnect coil integrated module connector.
3. Measure the FL speed sensor resistance between coil
integrated module connector (C-6) terminals 2 and 10.
Is the resistance between 2.0k and 2.8k ohms?
Go to Step 2Go to Step 3
2Measure the FR speed sensor resistance between coil integrated
module connector (C-6) terminals 3 and 11.
Is the resistance between 2.0k and 2.8 k ohms?
Go to Step 5Go to Step 4
3Measure the FL speed sensor resistance at the sensor connector.
Is the resistance between 2.0k and 2.8k ohms?Repair harness
abnormality
between sensors
and coil
integrated
module.
Go to
Step 2
Replace sensor.
Go to
Step 2
4Measure the FR speed sensor resistance at the sensor
connector.
Is the resistance between 2.0k and 2.8k ohms?Repair harness
abnormality
between sensors
and coil
integrated
module.
Go to
Step 5
Replace sensor.
Go to
Step 5
5Damage and powered iron sticking to sensor/sensor ring?Repair.
Go to
Step 6Go to Step 6
6Is there play sensor/sensor rotor?Repair.
Go to
Step 7Go to Step 7
7Is sensor output normal? (Chart C-1-1&C-1-2 or TC-1)Check for faults
in harness
between speed
sensor and coil
integrated
module.
Fault found:
repair, and
perform system
self-check.
No fault found:
replace EHCU.
Go to
Step 8
Replace sensor.
Go to
Step 8
81. Reconnect all components, ensure all components are
properly mounted.
2. Clear diagnostic trouble code.
Was this step finished?
Repeat ªBasic
diagnostic flow
chartº
Go to Step 8
NOTE: Even after repairing the faulty part the warning
light (W/L) does not go out if the vehicle is at a stop. Turn
the ignition switch to the ON position and drive the vehicle
at 12 km/h (8 mph) or higher to make sure that the
warning light goes out.

5A±53
BRAKE CONTROL SYSTEM
Unit Inspection Procedure
This section describes the following inspection
procedures referred to during
Symptom Diagnosis and
Diagnosis By ªABSº Warning Light Illumination Pattern
without TECH 2with TECH 2
Sensor Output InspectionChart C-1-1 to C-1-3Chart TC-1
Chart C-1-1 FL Sensor Output Inspection Procedure
StepActionYe sNo
11. Turn the key off.
2. Disconnect coil integrated module connector.
3. Jack up the vehicle with all four wheels off the ground.
Measure the AC voltage between coil integrated module
connector terminals while turning FL wheel at a speed of 1
RPS:
Is the voltage between coil integrated module connector (C-6)
terminals 2 and 10 less than 200 mV?
Go to Step 2
OK.
Go to
Step 3
21. Disconnect the wheel speed sensor.
2. Measure resistance between the wheel speed sensor
connector terminals 1 and 2.
Is the check between connector (C-28) terminals 1 and 2 within
2.0k - 2.8k ohms?Connector is
faulty, or open or
short circuit of
harness between
wheel speed
sensor connector
and coil
integrated
module.
Inspect and
correct the
connector or
harness.
Go to
Step 3
Wheel speed
sensor is faulty.
Replace the
wheel speed
sensor.
Go to
Step 3
3Reconnect all components, ensure all components are properly
mounted.
Was this step finished?Repeat the ªBasic
diagnostic flow
chartº
Go to Step 3

5A±54BRAKE CONTROL SYSTEM
Chart C-1-2 FR Sensor Output Inspection Procedure
StepActionYe sNo
11. Turn the key off.
2. Disconnect coil integrated module connector.
3. Jack up the vehicle with all four wheels off the ground.
Measure the AC voltage between coil integrated module
connector terminals while turning FR wheel at a speed of 1
RPS:
Is the voltage between coil integrated module connector (C-6)
terminals 3 and 11 less than 200 mV?
Go to Step 2
OK.
Go to
Step 3
21. Disconnect the wheel speed sensor.
2. Measure resistance between the wheel speed sensor
connector terminals 1 and 2.
Is the check between connector (C-1) terminals 1 and 2 within
2.0k - 2.8k ohms?Connector is
faulty, or open or
short circuit of
harness between
wheel speed
sensor connector
and coil
integrated
module.
Inspect and
correct the
connector or
harness.
Go to
Step 3
Wheel speed
sensor is faulty.
Replace the
wheel speed
sensor.
Go to
Step 3
3Reconnect all components, ensure all components are properly
mounted.
Was this step finished?Repeat the ªBasic
diagnostic flow
chartº
Go to Step 3
Chart C-1-3 Rear Sensor Output Inspection Procedure
StepActionYe sNo
11. Turn the key off.
2. Disconnect coil integrated module connector.
3. Jack up the vehicle with all four wheels off the ground measure
the AC voltage between coil integrated module connector
terminals while turning Rear wheel at a speed of 1 RPS:
Is the check between coil integrated module connector (C-6)
terminals 4 and 12 than under 200 mV?
Go to Step 2
OK.
Go to
Step 3
21. Disconnect the wheel speed sensor.
2. Measure resistance between the wheel speed sensor
connector terminals 1 and 2.
Is the check between connector (F-4) terminals 1 and 2 within
1.0k - 1.7k ohms?Connector is
faulty, or open or
short circuit of
harness between
wheel speed
sensor connector
and coil
integrated
module.
Inspect and
correct the
connector or
harness.
Go to
Step 3
Wheel speed
sensor is faulty.
Replace the
wheel speed
sensor.
Go to
Step 3
3Reconnect all components, ensure all components are properly
mounted.
Was this step finished?Repeat the ªBasic
diagnostic flow
chartº
Go to Step 3