2002 ISUZU AXIOM wheel

5C±112
POWER±ASSISTED BRAKE SYSTEM
Brake Lining
Brake Lining and Associated Parts
305RW001
Legend
(1) Wheel and Tire Assembly
(2) Drum
(3) Hold-down Spring and Cup
(4) Hold-down Spring and Cups
(5) Lower Return Spring
(6) Upper (other) Return Spring
(7) Trailing Shoe Assembly with Parking Brake
Lever
(8) Leading Shoe Assembly with Upper (inner)
Return Spring(9) Upper (inner) Return Spring
(10) Auto Adjuster Lever
(11) Parking Brake Lever
(12) Adjuster Assembly
(13) Wave Washer
(14) Retainer
(15) Hold-down Pin
(16) Hold-down Pin
Removal
1. Raise the vehicle and support with suitable safety
stands.
2. Remove wheel and tire assembly (1).

Refer to
Wheel and Tires in Wheel and Tire System
section.
3. Remove Drum (2).

If difficulty is encountered in removing the drum:
± Mark the position of the drum to the axle.
± Make sure the parking brake is released.± Use a rubber mallet to tap gently on the outer rim of
the drum and/or around the inner drum. Be careful
to avoid damaging the drum.
4. Remove upper (other) return spring (6) and auto
adjuster lever.
5. Remove lower return spring (5).
6. Remove hold-down spring and cups (4) and
hold-down pin (15).
7. Remove adjuster assembly (12)
8. Remove leading shoe assembly (8) with upper (inner)
return spring (9).

5C±114
POWER±ASSISTED BRAKE SYSTEM
8. Install adjuster assembly (12).
9. Install hold-down pin (15) and hold-down spring and
cups (4).
10. Install lower return spring (5).

Use brake spring tool.
11. Install auto adjuster lever (10).
12. Install upper (outer) return spring (6).

Use brake spring tool.
13. Install brake drum (2).

Adjust the brakes, refer to the
Drum Brake
Adjustment
in this section.
14. Install wheel and tire assembly (1).

Refer to
Wheels and Tires in wheel and Tire System
section.
Drum Brake Adjustment (4y2 Model)
NOTE: All brakes are self-adjusting. Brakes are adjusted
by repeated stepping on the brake pedal. (After stepping
on the pedal and releasing it, the rear auto adjuster, in the
rear brake, produces a clicking sound.
The same operation should be repeated until the sound
disappears.)
Take the following steps after overhauling the rear brake
assembly.
1. Move the parking brake handle to its fully released
position.
2. Parking cable must be loosened sufficiently. (Loosen
the adjust nut and the lock nut.)
3. Repeat stepping on the brake pedal firmly, and
releasing it until the clicking sound can no longer be
heard.
If the difference between the brake drum inside
diameter and diameter of the brake shoes is adjusted
to be 0,5 mm, the number of times for depressing the
brake pedal can be reduced.
4. Remove the drum. Measure the brake drum inside
diameter and diameter of the brake shoes.
Shoe clearance: 0.25-0.4 mm (0.0098-0.0157 in)
If incorrect, check the brake auto-adjusting system.
5. Rotate the adjust nut until all slack disappears from
the cable. Set the adjust nut.
6. Applying about 30 kg (66 lb) of force, pull the parking
brake handle to its fully set position three or four
times.
7. If the parking brake is properly adjusted, the travel
between the fully disengaged position and the fully
engaged position will be between 9 and 11 notches.
If the traveling range is not within these limits, again
repeat steps 1 through 5.
After adjusting has been done, check to see if the rear
wheel rotates smoothly without drag when turned by
hand.
Servicing The Brake Drum
Whenever the brake drums are removed, they should be
thoroughly cleaned and inspected for cracks, scores,
deep grooves and out-of-round.
Cracked, Scored or Grooved Drum
A cracked drum is unsafe and must be replaced.
Do not attempt to weld a cracked drum.
Smooth any slight scores. Heavy or extensive scoring will
cause excessive brake lining wear, and it will probably be
necessary to machine the drum braking surface.
If the brake linings are slightly worn and the drum is
grooved, the drum should be polished with fine emery
cloth but should not be machined. At this stage,
eliminating all the grooves in the drum and smoothing the
ridges on the lining would require the removal of too much
metal and lining. If left alone, the grooves and ridges
match and satisfactory service can be obtained. If brake
linings are to be replaced, a grooved drum should be
machined. Using a grooved drum with new linings will
create inefficient braking performance and cause the
linings to wear quicker.
Out-Of-Round Drum
An out-of-round drum makes accurate brake shoe
adjustment impossible and is likely to cause excessive
wear to other parts of the brake mechanism due to its
eccentric action. An out-of-round drum can also cause
severe and irregular tire tread wear as well as a pulsing
brake pedal. When the braking surface of a brake drum
exceeds the specification limit of 0.15 mm (0.006 in) in
out-of-round, the drum should be machined to true up the
braking surface. Out-of-round can be accurately
measured with an inside micrometer fitted with proper
extension rods. When measuring a drum for out-of-round
and wear, take measurements at the open and closed
edges of machines surfaces and at right angles to each
other.
Maximum out-of-round: 0.15 mm (0.006 in)
420RS034

5C±115 POWER±ASSISTED BRAKE SYSTEM
Machining The Drum
If a drum is to be machined, only enough metal should be
removed to obtain a true, smooth braking surface. If a
drum does not clean-up when machined to a maximum
diameter, it must be replaced. Removal of more metal willaffect dissipation of heat and may cause distortion of the
drum.
After refinishing, replace any drum that exceeds a
maximum inside diameter of 296.5 mm (11.673 in). Do
not use a brake drum that is not within the specification.
Maximum inside diameter: 296.5 mm (11.673 in)
Wheel Cylinder Assembly (4y2 Model)
Wheel Cylinder Assembly and Associated Parts
305RW003
Legend
(1) Brake Linings
(2) Wheel Cylinder(3) Bolts
(4) Brake Pipe
Removal
1. Remove brake linings (1).

Refer to
Brake Lining and Associated Parts in this
section.
2. Remove brake pipe (4).

Plug the opening in the line to prevent fluid loss and
contamination.
3. Remove bolts (3) and wheel cylinder (2).
Installation
1. Install wheel cylinder (2) and tighten bolts (3) to the
specified torque.
Torque: 10 N´m (8 lb ft)
2. Install brake pipe (4) and tighten the nut to the
specified torque.
Torque: 16 N´m (12 lb ft)
3. Install brake linings (1).

Refer to
Brake Lining Replacement in this section.

Bleed brake system. Refer to
Hydraulic Brake in
this section.

5C±116
POWER±ASSISTED BRAKE SYSTEM
Disassembled View
305RS006
Legend
(1) Boot
(2) Piston Assembly
(3) Piston Cup
(4) Return Spring
(5) Bleeder
(6) Wheel Cylinder
Disassembly
1. Remove boot (1) and piston assembly (2).
2. Remove piston cup (3) from piston assembly (2).
3. Remove return spring (4) and bleeder (5) from wheel
cylinder (6).
Inspection and Repair
1. Make necessary parts replacement if wear, damage,
corrosion or any other abnormal condition are found
through inspection.
Check the following parts;

Wheel cylinder body

Cylinder bore

Piston

Return spring

Bleeder
NOTE: Replace the piston cups and boots each time the
wheel cylinder is overhauled. Discard these used rubber
parts and replace with new ones.
Reassembly
1. Lubricate the cylinder bore with clean rubber grease.
305RS007
2. Install bleeder (5) to wheel cylinder (6).
Torque: 10 N´m (8 lb ft)
305RS008

5C±117 POWER±ASSISTED BRAKE SYSTEM
3. Install new piston cups (3) on each piston so that the
flared end of the cups are turned to the inboard side of
the pistons.
Attach the return spring (4) and the boot (1) to the
piston.
305RS009
4. Apply DELCO silicone lube No. 5459912 (or
equivalent) to the piston and the inner face of the
boots.
5. Install piston assembly (2) to wheel cylinder (6).

5C±118
POWER±ASSISTED BRAKE SYSTEM
Main Data and Specifications
General Specifications
Rear drum brake
TypeLeading-trailing, non-servo
Drum inside diameter295 mm (11.6 in)
Wheel cylinder diameter22.22 mm (7/8 in)
Torque Specifications
E05RW010

5D1±1
PARKING BRAKE SYSTEM (4x4 Model)
AXIOM
BRAKES
PARKING BRAKE SYSTEM (4y4 Model)
CONTENTS
Service Precaution 5D1±1. . . . . . . . . . . . . . . . . . . . . .
General Description 5D1±1. . . . . . . . . . . . . . . . . . . . .
Operation 5D1±2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Parking Brake Lever and Front Cable 5D1±3. . . . . .
Parking Brake Lever Assembly and
Associated Parts 5D1±3. . . . . . . . . . . . . . . . . . . . . .
Removal 5D1±3. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 5D1±3. . . . . . . . . . . . . . . . . . . . . . . . . . . . Parking Brake Rear Cable 5D1±4. . . . . . . . . . . . . . . .
Parking Brake Rear Cable and Associated
Parts 5D1±4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Removal 5D1±5. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation 5D1±5. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Inspection and Repair 5D1±6. . . . . . . . . . . . . . . . . .
Parking Brake Adjustment 5D1±6. . . . . . . . . . . . . . . .
Main Data and Specifications 5D1±7. . . . . . . . . . . . .
Service Precaution
WARNING: THIS VEHICLE HAS A SUPPLEMENTAL
RESTRAINT SYSTEM (SRS). REFER TO THE SRS
COMPONENT AND WIRING LOCATION VIEW IN
ORDER TO DETERMINE WHETHER YOU ARE
PERFORMING SERVICE ON OR NEAR THE SRS
COMPONENTS OR THE SRS WIRING. WHEN YOU
ARE PERFORMING SERVICE ON OR NEAR THE SRS
COMPONENTS OR THE SRS WIRING, REFER TO
THE SRS SERVICE INFORMATION. FAILURE TO
FOLLOW WARNINGS COULD RESULT IN POSSIBLE
AIR BAG DEPLOYMENT, PERSONAL INJURY, OR
OTHERWISE UNNEEDED SRS SYSTEM REPAIRS.
CAUTION: Always use the correct fastener in the
proper location. When you replace a fastener, use
ONLY the exact part number for that application.
ISUZU will call out those fasteners that require a
replacement after removal. ISUZU will also call out
the fasteners that require thread lockers or thread
sealant. UNLESS OTHERWISE SPECIFIED, do not
use supplemental coatings (Paints, greases, or other
corrosion inhibitors) on threaded fasteners or
fasteners joint interfaces. Generally, such coatings
adversely affect the fastener torque and the joint
clamping force, and may damage the fasteners.
When you install fasteners, use the correct
tightening sequence and specifications. Following
these instructions can help you avoid damage to
parts and systems.
General Description
Pulling up the parking brake lever by hand will set the
parking brake. By means of a ratchet type lock, the lever
can be held in that position until it is released. The position
of the lever is transmitted through cable/lever systems to
the rear wheels. These parts are designed to obtain
sufficient braking force even when parking on slopes.
When the parking brake is set, or when the ignition SW is
in theªONº position, the brake warning light illuminates.
The rear wheel parking brake is a duo±servo brake
(mechanical inside expansion type) built in the rear disc
brake. Parking brake adjustment is made through the
adjusting hole (bored through back plate). Parking brake
lever stroke should be adjusted to 6±8 notches. Refer to
Parking Brake Adjustment in this section.

5D1±4
PARKING BRAKE SYSTEM (4x4 Model)
Parking Brake Rear Cable
Parking Brake Rear Cable and Associated Parts
311RY00004
Legend
(1) Rear Wheels
(2) Caliper Assembly
(3) Rotor (Drum)
(4) Holding Spring
(5) Upper Return Spring
(6) Lower Return Spring
(7) Shoe Assembly(8) Cable Fixing Bolt
(9) Bolt
(10) Bolt
(11) Bolt (Only Long Wheel Base Model)
(12) Nut
(13) Nut
(14) Retainer
(15) Rear Cable