2002 BUICK RANDEZVOUS keyless entry

2-113
Interior Lighting On
The interior lighting on feature can be programmed to
one of the following modes:
KEY OUT: The interior lamps will come on for
about 25 seconds whenever you remove the key from
the ignition.
DOOR: The interior lamps will come on for about
25 seconds when any door is opened.
Interior lighting on will not occur while the ignition is in
ON. After 25 seconds have passed, the interior lamps
will slowly fade out. The lamps will fade out before the
25 seconds have passed if the following conditions
are met:

The ignition is turned to ON,

LOCK is pressed on the optional remote keyless
entry transmitter, or

there is no occupant activity detected for an
illumination period of 25 seconds.Before your vehicle was shipped from the factory, it was
programmed in DOOR. The mode to which the vehicle
has been programmed may have been changed since it
left the factory. To determine the mode to which your
vehicle is programmed or to program your vehicle to a
different mode, do the following:
1. Follow the instructions for ªEntering Programming
Modeº listed previously.
2. Press the MODE button until INTERIOR
LIGHTING ON appears on the DIC.
3. Press the SET button until the arrow is before KEY
OUT or DOOR.
The mode you selected is now set. You can either exit
programming mode by following the instructions later in
this section or program the next feature available on
your vehicle.

2-116
Delayed Locking
The delayed locking feature can be programmed to one
of the following modes:
ON: Lock your vehicle using the power door lock
switch or the optional remote keyless entry transmitter
while any door is opened, you will hear three chimes
and the doors will not lock. Five seconds after the last
door is closed, all doors will lock.
Once delayed locking is programmed to ON, you can do
the following:

Cancel the delayed locking by pressing unlock using
the power door lock switch or by fully inserting the
key in the ignition,

override the delayed locking feature by pressing lock
immediately using the power door lock switch, or

let the delayed locking feature complete the locking
of the vehicle.OFF: The doors will always lock immediately when
you lock the doors using the power door lock switch
or press LOCK on the optional remote keyless
entry transmitter.
Before your vehicle was shipped from the factory, it was
programmed in ON. The mode to which the vehicle has
been programmed may have been changed since it left
the factory. To determine the mode to which your
vehicle is programmed or to program your vehicle to a
different mode, do the following:
1. Follow the instructions for ªEntering Programming
Modeº listed previously.
2. Press the MODE button until DELAYED LOCKING
appears on the DIC.
3. Press the SET button until the arrow is before ON
or OFF.
The mode you selected is now set. You can either exit
programming mode by following the instructions later in
this section or program the next feature available on
your vehicle.

2-117
Remote Door Unlock
The remote door unlock feature can be programmed to
one of the following modes:
DRIVER/ALL: With the first press of UNLOCK on
the remote keyless entry transmitter, the driver's door
will unlock, and with the second press of UNLOCK,
within five seconds of the first press, all passenger's
doors will unlock.
ALL: All doors will unlock with every press of
UNLOCK on the remote keyless entry transmitter.Before your vehicle was shipped from the factory, it was
programmed in ALL. The mode to which the vehicle
has been programmed may have been changed since it
left the factory. To determine the mode to which your
vehicle is programmed or to program your vehicle to a
different mode, do the following:
1. Follow the instructions for ªEntering Programming
Modeº listed previously.
2. Press the MODE button until REMOTE DOOR
UNLOCK appears on the DIC.
3. Press the SET button until the arrow is before
DRIVER/ALL or ALL.
The mode you selected is now set. You can either exit
programming mode by following the instructions later in
this section or program the next feature available on
your vehicle.

2-118
Unlock Feedback
The unlock feedback feature can be programmed to one
of the following modes:
LIGHTS: This mode does the following:

During the day, when the ignition is in OFF and
UNLOCK on the remote keyless entry transmitter
is pressed, the headlamps and parking lamps will
flash, or

during the night, when the ignition is in OFF and the
headlamp exit delay feature is programmed to any
mode but OFF, the headlamps and parking lamps
will be activated for the same time period as the
headlamp exit delay feature is programmed to when
UNLOCK is pressed on the remote keyless entry
transmitter (see ªHeadlamp Exit Delayº earlier in
this section), or

during the night, when the ignition is in OFF and the
headlamp exit delay feature is programmed to OFF,
the headlamps and parking lamps will be activated
for 30 seconds when UNLOCK is pressed on the
remote keyless entry transmitter (see ªHeadlamp
Exit Delayº earlier in this section).OFF: The headlamps and parking lamps will not
flash when UNLOCK is pressed on the remote keyless
entry transmitter.
Before your vehicle was shipped from the factory, it was
programmed in LIGHTS. The mode to which the
vehicle has been programmed may have been changed
since it left the factory. To determine the mode to which
your vehicle is programmed or to program your vehicle
to a different mode, do the following:
1. Follow the instructions for ªEntering Programming
Modeº listed previously.
2. Follow the instructions for programming
HEADLAMP EXIT DELAY earlier in this section,
to make sure which mode it is programmed to.
3. Press the SET button until UNLOCK FEEDBACK
appears on the DIC.
4. Press the MODE button until the arrow is before
LIGHTS or OFF.
5. Press the SET button once you have determined
which mode you prefer.
The mode you selected is now set. You can either exit
programming mode by following the instructions later in
this section or program the next feature available on
your vehicle.

2-119
Lock Feedback
The lock feedback feature can be programmed to one of
the following modes:
OFF: When LOCK is pressed on the remote keyless
entry transmitter, the headlamps and parking lamps will
not flash and the horn will not sound.
LIGHTS: When LOCK is pressed on the remote
keyless entry transmitter, the headlamps and parking
lamps will flash briefly.
LIGHTS and HORN: When LOCK is pressed a
second time on the remote keyless entry transmitter
within five seconds, the headlamps and parking lamps
will flash briefly and the horn will sound.Before your vehicle was shipped from the factory, it was
programmed in LIGHTS and HORN. The mode to
which the vehicle has been programmed may have been
changed since it left the factory. To determine the mode
to which your vehicle is programmed or to program
your vehicle to a different mode, do the following:
1. Follow the instructions for ªEntering Programming
Modeº listed previously.
2. Press the MODE button until LOCK FEEDBACK
appears on the DIC.
3. Press the SET button until the arrow is before OFF,
LIGHTS or LIGHTS and HORN.
The mode you selected is now set. You can either exit
programming mode by following the instructions later in
this section or program the next feature available on
your vehicle.

2-120
Seat Recall
The seat recall feature can be programmed to one of the
following modes:
ON: The previously programmed memory seat position
will be recalled when the UNLOCK button is pressed on
the remote keyless entry transmitter.
OFF: No memory seat position will be recalled when
you press the UNLOCK button on the remote keyless
entry transmitter.
To determine the mode to which your vehicle is
programmed or to program your vehicle to a different
mode, do the following:
1. Follow the instructions for ªEntering Programming
Modeº listed previously.
2. Press the MODE button until SEAT RECALL
appears on the DIC.
3. Press the SET button until the arrow is before
ON or OFF.If the seat recall feature has been programmed to ON,
the seat recall feature can also be programmed to one of
the following modes:
MEMORY: The position recalled will be the memory
driving position.
EXIT: The position recalled will be the previously
programmed exit position.
To determine the mode to which your vehicle is
programmed or to program your vehicle to a different
mode, do the following:
1. Follow the instructions for ªEntering Programming
Modeº listed previously.
2. Follow the instructions for programming SEAT
RECALL to ON listed previously.
3. Press the MODE button until RECALL POSITION
appears on the DIC.
4. Press the SET button until the arrow is before
MEMORY or EXIT.
The mode you selected is now set. You can either exit
programming mode by following the instructions later in
this section or program the next feature available on
your vehicle.

6-66
Fuses Usage
16 Heated Mirrors
17 Power Mirrors
18 Ignition 1 Module
19 Turn Signal Switch and
NSBU Switch
21 Rear Defogger
22 Air Bag Module
24 Canister Vent Solenoid and
TCC Switch
25 HVAC Blower Motor
26 HVAC Mode and Temperature
Motors and Head
-Up Display
28 Not Used
29 Windshield Wipers and Washer
30 Instrument Panel Cluster,
BCM, PASS
-Key
III
31 Park Lock Ignition Key Solenoid
32 Rear Window Wiper/Washer
34 Power SunroofFuses Usage
35 Power Windows
36 Map Lamps, Courtesy Lamps and
Instrument Panel Lights
37 Radio
38 UQ3 Radio Amplifier
39 Head
-Up Display
40 Hazard Flashers
41 Instrument Panel Cluster, HVAC
Control, Security LED and
Remote Keyless Entry Module
42 PASS
-Key
III
44 Body Control Module (BCM)
Relays Usage
20 Rear Defogger Relay
23 IGN3 Relay
27 Accessory Relay
33 Retained Accessory Power Relay
Diode
43 Accessory Diode

6-69
J-Style Fuse Usage
38 Spare
39 Engine Cooling Fan
40 Engine Cooling Fan
41 Main Battery Fuse for Retained
Accessory Power Relay and
Accessory Relay
42 Main Battery Fuse for Heated
Seats, Air
43 Spare
44 Spare
45 Main Battery Fuse for Power
Outlets, Level Control,
Power Seats and Mirrors and
Body computer
46 Spare
47 Main Battery Fuse for HVAC
Blower and Ignition 3 relay
48 Main Battery fuse for Ignition
Switch, Radio, Heads
-Up Display,
Remote Keyless Entry (RKE),
Instrument Cluster, Air
Conditioning and Body ComputerMaxi Breaker Usage
49 Spare
Micro Relay Usage
50 Horn
51 Fuel Pump
52 Air Conditioning Clutch
53 Daytime Running Lamps (DRL)
54 Low
-Beam Headlamps
55 Parking Lamps
56 High
-Beam Headlamps
57 Fog Lamps
Mini Relay Usage
58 Starter Relay
59 Cooling Fan
60 Ignition 1 Relay
61 Cooling Fan
62 Cooling Fan
63 Air Pump