2002 BUICK RANDEZVOUS keyless entry

2-53 Interior Lamps Control
Turn the interior lamps control to one of the
following positions:

OFF: Use OFF to turn the interior lamps off.

DOOR: Use DOOR to turn on the interior lamps
when any door is opened and when the key is
removed from the ignition.

ON: Use ON to turn the interior lamps on.
Illuminated Entry
With illuminated entry, the interior of your vehicle will
illuminate for 25 seconds so you can see inside your
vehicle before you enter. To activate illuminated entry,
do the following:

Unlock a door using the key when the interior lamp
control is in the DOOR position, and when the
ignition is in OFF, or

press UNLOCK on the optional remote keyless entry
transmitter when the interior lamp control is in the
DOOR position, and when the ignition is in OFF.
After 25 seconds have passed, the interior lamps will
slowly fade out.The lamps will turn off before 25 seconds if you do one
of the following:

Press LOCK on the optional remote keyless entry
transmitter, or

press the front of the power door lock switch, or

turn the ignition to ON.
When any door is opened, illuminated entry is cancelled.
The interior lamps will stay on while any door or the
liftgate is open, and slowly fade out when all doors and
the liftgate are closed.Delayed Lighting
The delayed lighting feature will continue to illuminate
the interior for 25 seconds after all doors have been
closed so that you can find the ignition and buckle your
safety belt when it is too dark. The lamps will continue
to illuminate when the following conditions are met:

When a door is opened then closed,

when the interior lamp control is in the DOOR
position, and

when the ignition is in OFF.
After 25 seconds have passed, the interior lamps will
slowly fade out.

2-54
The lamps will fade out before the 25 seconds have
passed if the following conditions are met:

The ignition is turned to ON,

LOCK is pressed on the optional remote keyless
entry transmitter, or

the front of the power door lock switch is pressed.
If your vehicle is equipped with the Driver Information
Center (DIC), you can program this feature on or off.
See ªDriver Information Centerº in the Index.
Exit Lighting
With exit lighting, the interior lamps will come on for
about 30 seconds whenever you remove the key from
the ignition if the following conditions are met:

The vehicle is in PARK (P),

the key is out of the ignition,

the interior lamp control is in the DOOR
position, and

all of the doors are closed.
After 30 seconds have passed, the interior lamps will
slowly fade out.The interior lamps will slowly fade out before
30 seconds have passed, if the following conditions
are met:

The ignition is turned to ON,

LOCK is pressed on the optional remote keyless
entry transmitter, or

the front of the power door lock switch is pressed.
If your vehicle is equipped with the Driver Information
Center (DIC), you can program this feature on or off.
See ªDriver Information Centerº in the Index.Perimeter Lighting
The perimeter lighting feature will turn on the
headlamps and parking lamps for 25 seconds when the
following conditions are met:

The ignition is turned to OFF,

the exterior lamp control is in the AUTO position,

UNLOCK is pressed on the optional remote keyless
entry transmitter, and

it is dark enough outside.
After 25 seconds have passed, the headlamps and
parking lamps will turn off.

2-55
The lamps will turn off before the 25 seconds have
passed if the following conditions are met:

The ignition is turned to ON, or

the exterior lamp control is turned out of the
AUTO position.
To program the perimeter lighting feature, see ªRemote
Lock and Unlock Confirmationº under ªVehicle
Customizationº in the Index. If your vehicle is equipped
with the Driver Information Center (DIC), see ªDriver
Information Center, Remote Lock Feedbackº in
the Index.
Headlamp Exit Delay
The headlamp exit delay feature will turn on the
headlamps and parking lamps at night for 30 seconds if
the following conditions are met:

The ignition is turned to OFF,

the exterior lamp control is in the AUTO position,

LOCK is pressed on the optional remote keyless
entry transmitter, and

it is dark enough outside.
After 30 seconds have passed, the headlamps and
parking lamps will turn off.The lamps will turn off before the 30 seconds have
passed if the following conditions are met:

The ignition is turned to ON, or

the exterior lamp control is turned out of the
AUTO position.
To program the headlamp exit delay feature, see
ªVehicle Customizationº in the Index. If your vehicle is
equipped with the Driver Information Center (DIC), see
ªDriver Information Centerº in the Index.
Front Reading Lamps
There are two reading lamps located on the
rearview mirror.
To turn either reading lamp on or off, press the button
located next to each lamp.
These lamps will come on each time you open the
doors, if the interior lamp control is in the ON or
DOOR position.
Rear Reading Lamps
There are two reading lamps with coat hooks in the
second row headliner, above the rear doors.
To turn on or off either reading lamp, press the lens of
the lamp.

2-103 Program Mode Message
United States Canada
If you receive this message, your vehicle is in program
mode. You are ready to begin programming your
vehicle's customization features.
If your vehicle does not have the Driver Information
Center (DIC), see ªVehicle Customizationº in the Index.
If your vehicle is equipped with the Driver Information
Center (DIC), see ªDriver Information Centerº in
the Index.
Key Fob Battery Low Warning Message
United States Canada
If you receive this message, the battery in the
remote keyless entry needs to be replaced.
See ªBattery Replacementº in the Index for battery
replacement instructions.

2-106
When the ignition is turned to ON or START, the DIC
will display the following:
BUICK: BUICK will be displayed for three seconds.
DRIVER #: This message will be displayed for another
three seconds after BUICK appears in the display. This
display lets the driver know which driver's remote
keyless entry transmitter is being used and the driver's
customization features.
The DIC controls are
located to the left of the
steering column on the
instrument panel.
The DIC will be in the last mode displayed when the
engine was turned off. To select a different mode, press
MODE. The display will cycle through its options at
each press of MODE.MODE: This button lets you cycle through the options
on the display.
SET: This button is used to select and set the options to
your preference.
Driver Information Center (DIC) Messages
The DIC will always display the compass reading and
the outside temperature. If the temperature is below
38
F (3
C), the temperature reading will toggle
between displaying the temperature and the word ICE
for two minutes.
AVG ECONOMY: Average fuel economy is viewed as
a long term approximation of your overall driving
conditions. To learn the average fuel economy from a
new starting point, press and hold the SET button while
the average fuel economy is displayed on the DIC. The
average fuel economy will set to zero.
INST ECONOMY: Instantaneous fuel economy varies
with your driving conditions, such as acceleration,
braking and the grade of the road being traveled.

2-109
ZONE # PRESS & HOLD SET TO CHANGE: This
display mode will be displayed when you are manually
calibrating the system. The current zone number for
compass variance will be displayed in place of the
# symbol. Use the SET button to select the zone number
from the graphic shown to select the current area of the
country that you are driving in.
PRESS SET TO CALIBRATE COMPASS: After
selecting your zone, press the MODE button and this
will be displayed on the DIC. Press the SET button and
complete three 360 degree turns in an area free from
large metal objects.
The following two messages will toggle in the display
until you calibrate the compass:

DRIVE VEHICLE IN CIRCLE

CALIBRATING COMPASS
When calibration is complete, the display will return to
its normal mode.Driver Information Center (DIC)
Vehicle Customization
The DIC is used to program the choices of two drivers.
The drivers are recognized as DRIVER 1 and
DRIVER 2 in the DIC display. You will let the DIC
know which driver you are by using your remote keyless
entry transmitter. Each remote keyless entry transmitter
was pre
-programmed to belong to DRIVER 1 or
DRIVER 2. Each transmitter may be programmed
differently for each driver's preferences.
After you press the LOCK button on your transmitter
and the ignition key is in ON, the DIC will display the
identified driver number. The vehicle will also recall the
vehicle customization features that were last
programmed to correspond to your transmitter.
If you unlock your vehicle using your key instead of
your transmitter, the DIC will not change drivers and
your vehicle will recall the information from the last
transmitter used.

2-110
Entering Programming Mode
To program features, your vehicle must be in the
programming mode. Follow these steps:
1. Turn the ignition key to ON with the vehicle
in PARK (P).
2. Press and release the MODE button,
scrolling through the DIC messages, until
PERSONALIZATION PRESS SET TO
BEGIN is displayed.
3. Press the SET button and TO SELECT DRIVER
PRESS REMOTE LOCK will appear. Press the
LOCK button on the optional remote keyless entry to
start. This identifies which remote keyless entry
transmitter is being programmed by displaying
PERSONALIZATION FOR DRIVER 1 or
PERSONALIZATION FOR DRIVER 2.
United States Canada
4. The program mode message will appear in the
message center as an indication that your vehicle is
ready to begin programming.
5. Follow the instructions given by the DIC.

2-112
Interior Lighting Delay
The interior lighting delay feature can be programmed
to one of the following modes:
ON: Continue to illuminate the interior lamps for
25 seconds after all doors have been closed so that
you can find your ignition and buckle your safety belt
at night.
Interior lighting delay will not occur while the ignition
is in ON. After 25 seconds have passed, the interior
lamps will slowly fade out. The lamps will fade out
before the 25 seconds have passed if the following
conditions are met:

The ignition is turned to ON,

all doors are locked using the optional remote
keyless entry transmitter, or

there is no occupant activity detected for an
illumination period of 25 seconds.
OFF: The interior will not illuminate your vehicle when
all of the doors are closed.Before your vehicle was shipped from the factory, it was
programmed in ON. The mode to which the vehicle has
been programmed may have been changed since it left
the factory. To determine the mode to which your
vehicle is programmed or to program your vehicle to a
different mode, do the following:
1. Follow the instructions for ªEntering Programming
Modeº listed previously.
2. Press the MODE button until INTERIOR
LIGHTING DELAY appears on the DIC.
3. Press the SET button until the arrow is before ON
or OFF.
The mode you selected is now set. You can either exit
programming mode by following the instructions later in
this section or program the next feature available on
your vehicle.