2001 TOYOTA SEQUOIA actuator

V08425
LOCK
KNK
E6 Connector
(a) Remove the glove compartment (See page SF±68).
(b) Disconnect the E6 connector of ECM.
INSPECTION PROCEDURE
Replace knock sensor. 1 Check continuity between terminal KNK of ECM connector and body ground.
OK:
Check knock sensor (See page SF±61).Measure resistance between terminal KNK of ECM connector
and body ground.
Resistance: 1 MW or higher
Connector being checked is connected.  Indicates the condition of the connector of ECU during the check.
PREPARATION:
CHECK:
2Go to step 3.
OK OK
NG
 Indicates the position of the ignition switch during the check.
Check from the connector back side.
(with harness)
Ignition Switch LOCK (OFF)
Ignition Switch START
LOCKIgnition Switch ON
Ignition Switch ACC
STARTON
ACC

 Indicates the place to check the voltage or resistance.
 Indicates the connector position to be checked, from the front or back side.
Connector being checked is disconnected. Check from the connector front side. (without harness)
In this case, care must be taken not to bend the terminals.
E6 Connector KNKWire Harness
E6 Connector KNK
A00255 AB0117
A00265
Inspection Procedure
Use the inspection procedure to determine if
the circuit is normal or abnormal, and, if it is
abnormal, use it to determine whether the
problem is located in the sensors, actuators,
wire harness or ECU. IN±34
± INTRODUCTIONHOW TO TROUBLESHOOT ECU CONTROLLED
SYSTEMS
34 Author: Date:
2005 SEQUOIA (RM1146U)

FI0048
FI0047
FI0046
IN011±61
± INTRODUCTIONHOW TO TROUBLESHOOT ECU CONTROLLED
SYSTEMSIN±35
35 Author: Date:
2005 SEQUOIA (RM1146U)
HOW TO USE THE DIAGNOSTIC
CHART AND INSPECTION
PROCEDURE
1. CONNECTOR CONNECTION AND TERMINAL IN-
SPECTION

For troubleshooting, diagnostic trouble code charts or
problem symptom table are provided for each circuit with
detailed inspection procedures on the following pages.

When all the component parts, wire harnesses and con-
nectors of each circuit except the ECU are found to be
normal in troubleshooting, then it is determined that the
problem is in the ECU. Accordingly, if diagnosis is per-
formed without the problem symptoms occurring, refer to
step 8 to replace the ECU. So always confirm that the
problem symptoms are occurring, or proceed with inspec-
tion while using the symptom simulation method.

The instructions ºCheck wire harness and connectorº and
ºCheck and replace ECUº which appear in the inspection
procedure, are common and applicable to all diagnostic
trouble codes. Follow the procedure outlined below
whenever these instructions appear.
OPEN CIRCUIT:
This could be due to a disconnected wire harness, faulty con-
tact in the connector, and a connector terminal pulled out, etc.
HINT:

It is rarely the case that a wire is broken in the middle of
it. Most cases occur at the connector. In particular, care-
fully check the connectors of sensors and actuators.

Faulty contact could be due to rusting of the connector
terminals, to foreign materials entering terminals or a de-
formation of connector terminals. Simply disconnecting
and reconnecting the connectors once changes the
condition of the connection and may result in a return to
normal operation. Therefore, in troubleshooting, if no ab-
normality is found in the wire harness and connector
check, but the problem disappears after the check, then
the cause is considered to be in the wire harness or con-
nectors.
SHORT CIRCUIT:
This could be due to a contact between wire harness and the
body ground or to a short circuit occurred inside the switch, etc.
HINT:
When there is a short circuit between the wire harness and body
ground, check thoroughly whether the wire harness is caught
in the body or is clamped properly.

PP1DZ±02
PP±42
± PREPARATIONTRANSFER
100 Author: Date:
2005 SEQUOIA (RM1146U)
SSM (Special Service Materials)
08826±00080Seal Packing Black or equivalent
(FIPG)
08826±00090Seal Packing 1281,
THREE BOND 1281 or equivalent
(FIPG)Front case x Rear case
Rear case x Case cover
Case x Extension housing
Motor actuator x Front case

SS0PY±05
SS±28
± SERVICE SPECIFICATIONSTRANSFER
170 Author: Date:
2005 SEQUOIA (RM1146U)
TORQUE SPECIFICATION
Part tightenedN´mkgf´cmft´lbf
Transfer x Transfer adaptor2424518
Engine rear mounting x Transmission6566048
Crossmember x Frame7273053
Engine rear mounting x Crossmember1818513
Heat insulator x Crossmember1616412
Front suspension member bracket x Crossmember3333624
Filler plug x Transfer3737727
Rear propeller shaft x Rear differential8889765
Rear propeller shaft x Transfer8889765
Protector x Transfer1818513
Front propeller shaft x Front differential7475054
Front propeller shaft x Transfer8889765
Front exhaust pipe x Exhaust manifold6263046
Front exhaust pipe x Center exhaust pipe4849035
Transfer case cover x Transfer front case1818413
Case plug x Transfer front case18.619014
Front bearing retainer x Transfer front case11.511 98
Front output shaft companion flange lock nut11 81,20387
Oil pump x Front case7.56966 in.´lbf
Oil separator x Front case7.56966 in.´lbf
Transfer shift actuator x Transfer case rear2020415
Front case x Transfer case rear2828621
Shift shaft stopper1919414
Drain and filler plug3737727
Transfer extension housing x Transfer case rear121229
Rear output shaft companion flange lock nut11 81,20387
Gear shift fork2424518

SS1KF±04
± SERVICE SPECIFICATIONSSUSPENSION AND AXLE
SS±39
181 Author: Date:
2005 SEQUOIA (RM1146U)
TORQUE SPECIFICATION
Part tightenedN´mkgf´cmft´lbf
TIRE PRESSURE MONITOR RECEIVER
Tire pressure monitor receiver set bolt7.57666 in.´lbf
TIRE PRESSURE MONITOR VALVE
Tire pressure monitor valve set nut4.04135 in.´lbf
FRONT AXLE
Hub nut11 01,15083
Tie rod end lock nut5556041
Steering knuckle x Brake caliper8082059
Steering knuckle x Dust cover1231,25090
Drive shaft lock nut1818513
Upper suspension arm x Upper ball joint2352,400173
Brake line clamp x Steering knuckle1051,10077
ABS speed sensor x Steering knuckle2828521
ABS speed sensor wire harness clamp x Steering knuckle8.08271 in.´lbf
ABS speed sensor wire harness clamp x Upper suspension arm8.08271 in.´lbf
FRONT DIFFERENTIAL
Drive pinion x companion flangeSee page SA±43
Differential front mounting cushion x Chassis frame1371,400101
Differential rear mounting cushion x Chassis frame8789064
Differential front mounting cushion x Differential1571,60011 6
Differential rear mounting cushion x Differential1081,10080
Ring gear x Differential case9798571
Differential carrier x Differential tube7880058
Differential carrier x Side bearing retainer6970051
Differential x Front propeller shaft7475054
A.D.D. clutch case x Differential7880058
A.D.D. clutch case x Differential tube7880058
A.D.D. actuator x A.D.D. clutch case2121015
Tube with wire harness assembly clamp x Differential carrier131309
Drain plug6566048
Filler plug3940029
FRONT SUSPENSION
Suspension support x Chassis frame6465047
Piston rod x Suspension support2525018
Lower suspension arm x Shock absorber1351,400100
Upper suspension arm x Chassis frame981,00072
Lower suspension arm x Chassis frame1301,32596
Lower suspension arm x Lower ball joint1591,62111 7
Power steering gear Left side nut
Center bolt
Right side bolt and nut130
165
1651,350
1,700
1,70096
122
122
Tie rod end x Lower ball joint9193067
No. 1, No. 2 spring bumper31 (23)315 (235)23 (17)
Lower suspension arm x Stabilizer bar link6970051

SS085±04
± SERVICE SPECIFICATIONSBRAKE
SS±43
185 Author: Date:
2005 SEQUOIA (RM1146U)
TORQUE SPECIFICATION
Part tightenedN´mkgf´cmft´lbf
Bleeder plug1111 08
Master cylinder x Reservoir1.51513 in.´lbf
Master cylinder x Brake booster2525018
Master cylinder x Master cylinder pressure sensor2525018
Brake booster clevis lock nut2525018
Brake booster x Brake booster bracket2525018
Brake booster x Pedal bracket131309
Brake pedal x Pedal bracket3435025
Stop light switch lock nut2526019
Parking brake pedal assembly x Pedal bracket3232023
Parking brake pedal assembly x Body131309
Brake line union nut 10 mm1515511
12 mm19.519514
Front disc brake caliper x Steering knuckle1231,25090
Rear disc brake caliper installation bolt8890065
Rear disc brake caliper x Flexible hose3132023
Rear disc brake torque plate x Backing plate1051,07077
Actuator bracket x Body1111 28
Actuator bracket x Actuator assembly9.59784 in.´lbf
Actuator x Skid control ECU1.81816 in.´lbf
Speed sensor installation bolt8.08271 in.´lbf
Front speed sensor harness x Steering knuckle8.08271 in.´lbf
Front speed sensor harness x Upper arm8.08271 in.´lbf
Front speed sensor harness x Coil support8.08271 in.´lbf

DID7O±02
± DIAGNOSTICSENGINE
DI±3
197 Author: Date:
2005 SEQUOIA (RM1146U)
TOYOTA PART AND SYSTEM NAME LIST
This reference list indicates the part names used in this manual along with their definitions.
TOYOTA/LEXUS nameDefinition
Toyota HCAC system, Hydro±carbon Adsorptive Catalyst
(HCAC) system, HC adsorptive three±way catalystHC adsorptive three±way catalytic converter
Variable Valve Timing sensor, VVT sensorCamshaft position sensor
Variable valve timing system, VVT systemCamshaft timing control system
Camshaft timing oil control valve, Oil control valve, OCV,
VVT, VSVCamshaft timing oil control valve
Variable timing and lift, VVTLCamshaft timing and lift control
Crankshaft position sensor ºAºCrankshaft position sensor
Engine speed sensorCrankshaft position sensor
THAIntake air temperature
Knock control moduleEngine knock control module
Knock sensorEngine knock sensor
Mass or volume air flow circuitMass air flow sensor circuit
Vacuum sensorManifold air pressure sensor
Internal control module, Control module, Engine control
ECU, PCMPower train control module
FC idleDeceleration fuel cut
Idle air control valveIdle speed control
VSV for CCV, Canister close valve VSV for canister controlEvaporative emissions canister vent valve
VSV for EVAP, Vacuum switching valve assembly No. 1,
EVAP VSV, Purge VSVEvaporative emissions canister purge valve
VSV for pressure switching valve, Bypass VSVEvaporative emission pressure switching valve
Vapor pressure sensor, EVAP pressure sensor, Evaporative
emission control system pressure sensorFuel tank pressure sensor
Charcoal canisterEvaporative emissions canister
ORVR systemOn±board refueling vapor recovery system
Intake manifold runner controlIntake manifold tuning system
Intake manifold runner valve, IMRV, IACV (runner valve)Intake manifold tuning valve
Intake control VSVIntake manifold tuning solenoid valve
AFSAir fuel ratio sensor
O2 sensorHeater oxygen sensor
Oxygen sensor pumping current circuitOxygen sensor output signal
Oxygen sensor reference ground circuitOxygen sensor signal ground
Accel position sensorAccelerator pedal position sensor
Throttle actuator control motor, Actuator control motor, Elec-
tronic throttle motor, Throttle control motorElectronic throttle actuator
Electronic throttle control system, Throttle actuator control
systemElectronic throttle control system
Throttle/pedal position sensor, Throttle/pedal position switch,
Throttle position sensor/switchThrottle position sensor
Turbo press sensorTurbocharger pressure sensor
Turbo VSVTurbocharger pressure control solenoid valve
P/S pressure switchPower±steering pressure switch
VSV for ACMActive control engine mount

A23651
20 msec./DIV 5 V/DIV
(a)
(b)
Ground
Ground
A23652
10 msec./DIV 1 V/DIV
Ground
A23653
1 msec./DIV 5 V/DIV
Ground
A23654
1 msec./DIV 5 V/DIV
Ground
A23655
(a)
(b)
20 msec./DIV 2 V/DIV
Ground
Ground
DI±38
± DIAGNOSTICSENGINE
232 Author: Date:
2005 SEQUOIA (RM1146U)
WAVEFORM 5
(a) Camshaft position sensor
(b) Crankshaft position sensor
ECM Terminal Name(a) Between G2+ and G2±
(b) Between NE+ and NE±
Tester Range5 V/DIV, 20 msec./DIV
ConditionIdle after engine warmed±up
HINT:
The wavelength becomes shorter as the engine rpm increases.
WAVEFORM 6
Vehicle speed signal
ECM Terminal NameBetween SP2+ and SP2±
Tester Range5 V/DIV, 10 msec./DIV
ConditionDriving by 40 km/h (25 mph)
HINT:
The wavelength becomes shorter as vehicle speed increases.
WAVEFORM 7
Throttle actuator positive terminal
ECM Terminal NameBetween M+ and ME01
Tester Range5 V/DIV, 1 msec./DIV
ConditionIdle after engine warmed±up
HINT:
The duty ratio varies depending on the throttle opening opera-
tion.
WAVEFORM 8
Throttle actuator negative terminal
ECM Terminal NameBetween M± and ME01
Tester Range5 V/DIV, 1 msec./DIV
ConditionIdle after engine warmed±up
HINT:
The duty ratio varies depending on the throttle opening opera-
tion.
WAVEFORM 9
(a) Igniter IGT signal (from ECM to igniter)
(b) Igniter IGF signal (from igniter to ECM)
ECM Terminal Name(a) Between IGT1 (to IGT8) and E1
(b) Between IGF1 (IGF2) and E1
Tester Range2 V/DIV, 20 msec./DIV
ConditionIdling
HINT:
The wavelength becomes shorter as vehicle speed increases.