2001 TOYOTA SEQUOIA shield

C91384H01010G27652H23575
Curtain Shield
Airbag Sensor
Assembly LH
Floor Wire No. 2
Airbag
Sensor
Assembly
VUCL
ESCL
A
B C D
VUCL ESCLSST
A19S26
DI±1200
± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
1394 Author: Date:
2005 SEQUOIA (RM1146U)
2 Check connection of connectors.
PREPARATION:
(a) Turn the ignition switch to the LOCK position.
(b) Disconnect the negative (±) terminal cable from the battery, and wait for at least 90 seconds.
CHECK:
Check that the connectors are properly connected to the airbag sensor assembly and the curtain shield air-
bag sensor assembly LH.
OK:
The connectors are connected securely.
NG Connect connectors, then go to step 1.
OK
3 Check floor wire No. 2 (open).
PREPARATION:
(a) Disconnect the connectors from the airbag sensor as-
sembly and the curtain shield airbag sensor assembly LH.
(b) Using SST, connect S26±2 (VUCL) and S26±1 (ESCL) of
connector ºCº.
SST 09843±18040
CHECK:
Measure the resistance according to the value(s) in the table
below.
OK:
Tester ConnectionConditionSpecified Condition
A19±20 (VUCL) ±
A19±22 (ESCL)AlwaysBelow 1 W
NG Repair or replace floor wire No. 2.
OK

C91384H01010G27652H23572
Curtain Shield
Airbag Sensor
Assembly LH
Floor Wire No. 2
Airbag
Sensor
Assembly
VUCL ESCL
A
B
C D
A19
C91384H01010G27652H23572
Curtain Shield
Airbag Sensor
Assembly LH
Floor Wire No. 2
Airbag
Sensor
Assembly
VUCL ESCL
A
B
C D
A19
± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
DI±1201
1395 Author: Date:
2005 SEQUOIA (RM1146U)
4 Check floor wire No. 2 (short).
PREPARATION:
Disconnect the SST from connector ºCº.
CHECK:
Measure the resistance according to the value(s) in the table
below.
OK:
Tester ConnectionConditionSpecified Condition
A19±20 (VUCL) ±
A19±22 (ESCL)Always1 MW or higher
NG Repair or replace floor wire No. 2.
OK
5 Check floor wire No. 2 (short to B+).
PREPARATION:
(a) Connect the negative (±) terminal cable to the battery,
and wait for at least 2 seconds.
CHECK:
(a) Turn the ignition switch to the ON position.
(b) Measure the voltage according to the value(s) in the table
below.
OK:
Tester ConnectionConditionSpecified Condition
A19±20 (VUCL) ±
Body groundIgnition switch ONBelow 1 V
A19±22 (ESCL) ±
Body groundIgnition switch ONBelow 1 V
NG Repair or replace floor wire No. 2.
OK

C91384H01010G27652H23572
Curtain Shield
Airbag Sensor
Assembly LH
Floor Wire No. 2
Airbag
Sensor
Assembly
VUCL ESCL
A
B
C D
A19
DI±1202
± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
1396 Author: Date:
2005 SEQUOIA (RM1146U)
6 Check floor wire No. 2 (short to ground).
PREPARATION:
(a) Turn the ignition switch to the LOCK position.
(b) Disconnect the negative (±) terminal cable from the bat-
tery, and wait for at least 90 seconds.
CHECK:
Measure the resistance according to the value(s) in the table
below.
OK:
Tester ConnectionConditionSpecified Condition
A19±20 (VUCL) ±
Body groundAlways1 MW or higher
A19±22 (ESCL) ±
Body groundAlways1 MW or higher
NG Repair or replace floor wire No. 2.
OK

H01007
H10600H42066H40997H23576
CG
TCDTC B1630/23
DLC3
Curtain Shield Airbag
Sensor Assembly RH
DTC B1635/24 Airbag
Sensor
Assembly
± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
DI±1203
1397 Author: Date:
2005 SEQUOIA (RM1146U)
7 Check curtain shield airbag sensor assembly LH.
PREPARATION:
(a) Connect the connectors to the airbag sensor assembly.
(b) Interchange the curtain shield airbag sensor assembly
RH with LH and connect the connectors to them.
(c) Connect the negative (±) terminal cable to the battery,
and wait for at least 2 seconds.
CHECK:
(a) Turn the ignition switch to the ON position, and wait for at
least 60 seconds.
(b) Clear the DTCs stored in memory (see page DI±1147).
(c) Turn the ignition switch to the LOCK position.
(d) Turn the ignition switch to the ON position, and wait for at
least 60 seconds.
(e) Check the DTCs (see page DI±1147).
OK:
DTC B1635/24 is output.A
DTC B1630/23 is output.B
DTC B1630/23 and B1635/24 are not
output.C
HINT:
Codes than other DTC B1630/23 and B1635/24 may be output
at this time, but they are not related to this check.
A Replace airbag sensor assembly
(see page RS±82).
B Replace curtain shield airbag sensor assembly
LH (see page RS±97).
C
From the results of the above inspection, the malfunctioning part can now be considered normal.
To make sure of this, use the simulation method to check (see page DI±1137).

DI±1206
± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
1400 Author: Date:
2005 SEQUOIA (RM1146U)
3 Check connection of connectors.
PREPARATION:
(a) Turn the ignition switch to the LOCK position.
(b) Disconnect the negative (±) terminal cable from the battery, and wait for at least 90 seconds.
CHECK:
Check that the connectors are properly connected to the airbag sensor assembly and the occupant classifi-
cation ECU.
OK:
The connectors are connected securely.
NG Connect connectors, then go to step 1.
OK
4 Prepare for inspection.
CAUTION:
Be sure to perform the following procedures before troubleshooting to avoid unexpected airbag de-
ployment.
(a) Disconnect the connectors from the airbag sensor assembly.
(b) Disconnect the connectors from the steering wheel pad.
(c) Disconnect the connectors from the front passenger airbag assembly.
(d) w/ Side and curtain shield airbag:
Disconnect the connectors from the side airbag assembly LH and RH.
(e) w/ Side and curtain shield airbag:
Disconnect the connectors from the curtain shield airbag assembly LH and RH.
(f) Disconnect the connectors from the front seat outer belt LH and RH.
NEXT

H10600H01007H43920H23364
DLC3
CG TCDTC B1653/35
Seat
Position
Airbag
Sensor
AssemblyAirbag
Sensor
Assembly
DI±1214
± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
1408 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION PROCEDURE
CAUTION:
Be sure to perform the following procedures before troubleshooting to avoid unexpected airbag de-
ployment.
(a) Turn the ignition switch to the LOCK position.
(b) Disconnect the negative (±) terminal cable from the battery, and wait for at least 90 seconds.
(c) Disconnect the connectors from the airbag sensor assembly.
(d) Disconnect the connectors from the steering wheel pad.
(e) Disconnect the connectors from the front passenger airbag assembly.
(f) w/ Side and curtain shield airbag:
Disconnect the connectors from the side airbag assembly LH and RH.
(g) w/ Side and curtain shield airbag:
Disconnect the connectors from the curtain shield airbag assembly LH and RH.
(h) Disconnect the connectors from the front seat outer belt LH and RH.
1 Check DTC.
PREPARATION:
(a) Connect the connectors to the airbag sensor assembly.
(b) Connect the negative (±) terminal cable to the battery,
and wait for at least 2 seconds.
CHECK:
(a) Turn the ignition switch to the ON position, and wait for at
least 60 seconds.
(b) Clear the DTCs stored in memory (see page DI±1147).
(c) Turn the ignition switch to the LOCK position.
(d) Turn the ignition switch to the ON position, and wait for at
least 60 seconds.
(e) Check the DTCs (see page DI±1147).
OK:
DTC B1653/35 is not output.
HINT:
Codes other than DTC B1653/35 may be output at this time, but
they are not related to this check.
NG Go to step 2.
OK
From the results of the above inspection, the malfunctioning part can now be considered normal.
To make sure of this, use the simulation method to check (see page DI±1137).

C84216
H10600C92968H24657
CG
TCDTC B1656/38
DLC3Airbag
Sensor
Assembly Front Seat
Inner Belt LH
± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
DI±1221
1415 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION PROCEDURE
CAUTION:
Be sure to perform the following procedures before troubleshooting to avoid unexpected airbag de-
ployment.
(a) Turn the ignition switch to the LOCK position.
(b) Disconnect the negative (±) terminal cable from the battery, and wait for at least 90 seconds.
(c) Disconnect the connectors from the airbag sensor assembly.
(d) Disconnect the connectors from the steering wheel pad.
(e) Disconnect the connectors from the front passenger airbag assembly.
(f) w/ Side and curtain shield airbag:
Disconnect the connectors from the side airbag assembly LH and RH.
(g) w/ Side and curtain shield airbag:
Disconnect the connectors from the curtain shield airbag assembly LH and RH.
(h) Disconnect the connectors from the front seat outer belt LH and RH.
1 Check DTC.
PREPARATION:
(a) Connect the connectors to the airbag sensor assembly.
(b) Connect the negative (±) terminal cable to the battery,
and wait for at least 2 seconds.
CHECK:
(a) Turn the ignition switch to the ON position, and wait for at
least 60 seconds.
(b) Clear the DTCs stored in memory (see page DI±1147).
(c) Turn the ignition switch to the LOCK position.
(d) Turn the ignition switch to the ON position, and wait for at
least 60 seconds.
(e) Check the DTCs (see page DI±1147).
OK:
DTC B1656/38 is not output.
HINT:
Codes other than DTC B1656/38 may be output at this time, but
they are not related to this check.
NG Go to step 2.
OK
From the results of the above inspection, the malfunctioning part can now be considered normal.
To make sure of this, use the simulation method to check (see page DI±1137).

H24023
DI±1230
± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
1424 Author: Date:
2005 SEQUOIA (RM1146U)
2 Check integration control and panel (passenger airbag ON/OFF indicator).
PREPARATION:
(a) Turn the ignition switch to the LOCK position.
(b) Disconnect the negative (±) terminal cable from the bat-
tery, and wait for at least 90 seconds.
(c) Disconnect the connectors from the airbag sensor as-
sembly.
(d) Connect the negative (±) terminal cable to the battery,
and wait for at least 2 seconds.
CHECK:
(a) Turn the ignition switch to the ON position.
(b) Check the passenger airbag ON/OFF indicator operation.
OK:
Neither the ºONº nor ºOFFº passenger airbag ON/
OFF indicators come on.
NG Go to step 3.
OK
Replace airbag sensor assembly (see page RS±82).
3 Prepare for inspection.
PREPARATION:
CAUTION:
Be sure to perform the following procedures before troubleshooting to avoid unexpected airbag de-
ployment.
(a) Turn the ignition switch to the LOCK position.
(b) Disconnect the negative (±) terminal cable from the battery, and wait for at least 90 seconds.
(c) Disconnect the connectors from the airbag sensor assembly.
(d) Disconnect the connectors from the steering wheel pad.
(e) Disconnect the connectors from the front passenger airbag assembly.
(f) w/ Side and curtain shield airbag:
Disconnect the connectors from the side airbag assembly LH and RH.
(g) w/ Side and curtain shield airbag:
Disconnect the connectors from the curtain shield airbag assembly LH and RH.
(h) Disconnect the connectors from the front seat outer belt LH and RH.
NEXT