2001 TOYOTA SEQUOIA battery

I28701
Wire Harness Side:
Lumbar Support Control Switch
L4
I28702
Lumbar Support Control Motor
Clockwise
Counter-
clockwise
Driving AxisL3
± DIAGNOSTICSPOWER SEAT CONTROL SYSTEM (w/ Driving Position
Memory)DI±1523
1717 Author: Date:
2005 SEQUOIA (RM1146U)
3 Check harness and connector (Power source).
CHECK:
Measure the voltage of each terminal of the wire harness side
connectors.
OK:
Tester ConnectionConditionSpecified Condition
L4±3 ± Body groundAlways10 to 14 V
CHECK:
Measure the resistance of each terminal, as shown in the il-
lustration and table.
OK:
Tester ConnectionConditionSpecified Condition
L4±2 ± Body groundAlwaysBelow 1 W
L4±5 ± Body groundAlwaysBelow 1 W
NG Repair or replace harness or connector.
OK
4 Inspect lumbar support control motor.
PREPARATION:
Remove the lumbar support control motor (See page BO±112).
CHECK:
Check that the motor rotates smoothly when the battery is con-
nected to the lumbar support control motor connector terminals.
OK:
Measurement ConditionOperational Direction
Battery positive (+) "1
Battery negative (±) " 2Clockwise
Battery positive (+) " 2
Battery negative (±) " 1Counterclockwise
NG Replace lumbar support control motor
(See page BO±112).
OK

I07253
1 21 2
DI±1526± DIAGNOSTICSPOWER SEAT CONTROL SYSTEM (w/ Driving Position
Memory)
1720 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION PROCEDURE
1 Inspect power seat motor assy.
PREPARATION:
Remove the power seat motor (See page BO±112).
CHECK:
Check that the motor rotates smoothly when the battery is con-
nected to the connector terminal.
OK:
Tester ConnectionSpecified Condition
Battery positive voltage ± 1
Battery negative voltage ± 2Counterclockwise
Battery positive voltage ± 2
Battery negative voltage ± 1Clockwise
NG Replace power seat motor (See page BO±112).
OK

I28451
BatteryJ/C
I18
Ignition SW
1
2
AM1IG1
5W BF10
FL Block
ALT
81L 1CInstrument Panel J/B
7 J52 J51
21AM1
6
1C4
1 78 L±Y1
MPX1 M6 WW
C5 C53430 Combination MeterPosition Control
ECU & Switch
P
L±Y
L±R
L±R CCPL RB 62 P1
Park/Neutral
Position Switch
B±Y
W±LGAUGEIPOIG49 BEAN
1D DI±1528
± DIAGNOSTICSPOWER SEAT CONTROL SYSTEM (w/ Driving Position
Memory)
1722 Author: Date:
2005 SEQUOIA (RM1146U)
Park/neutral position switch circuit
CIRCUIT DESCRIPTION
The power seat memory system operates only when the ignition switch is in the ON position and the park/
neutral position is in the P (park) position.
The position control ECU & switch assy detects the P position, via multiplex communication, through the
park/neutral position switch.
WIRING DIAGRAM
DIDEC±01

I28707
Wire Harness Side:
Park/Neutral Position Switch
P1
PL
I27704
Combination Meter Wire Harness View:
C5±34C5
I28707
Wire Harness Side:
Park/Neutral Position Switch
P1RB
± DIAGNOSTICSPOWER SEAT CONTROL SYSTEM (w/ Driving Position
Memory)DI±1531
1725 Author: Date:
2005 SEQUOIA (RM1146U)
4 Check harness and connector (Combination meter ± park/neutral position switch
assy).
CHECK:
Measure the resistance of each terminal of the wire harness
side connectors.
OK:
Tester Connection
(Symbols)ConditionSpecified Condition
C5±34 ± P1±6 (PL)AlwaysBelow 1 W
C5±34 ± Body groundAlways10 kW or higher
NG Repair or replace harness or connector.
OK
5 Check harness and connector (Park/neutral position switch assy ± battery).
CHECK:
Measure the voltage of each terminal of the wire harness side
connectors.
OK:
Tester Connection
(Symbols)ConditionSpecified Condition
P1±2 (RB) ± Body groundIgnition switch ON10 to 14 V
NG Repair or replace harness or connector.
OK

DIDEX±01
DI±1536
± DIAGNOSTICSCRUISE CONTROL SYSTEM
1730 Author: Date:
2005 SEQUOIA (RM1146U)
CRUISE CONTROL SYSTEM
PRECAUTION
NOTICE:
When disconnecting the battery terminal, initialize the following system after the terminal is recon-
nected.
System NameSee Page
Back Door Power Window Control SystemBE±77

A08841
Hand±held Tester
DLC3
DIDEZ±01
A04550
DLC3 1 2345678
9
10 11 12 1314 15 16
± DIAGNOSTICSCRUISE CONTROL SYSTEM
DI±1543
1737 Author: Date:
2005 SEQUOIA (RM1146U)
DIAGNOSIS SYSTEM
1. DESCRIPTION
The ECM controls the cruise control system of the vehicle. The
data and DTCs relating to the cruise control system can be read
from the DLC3 of the vehicle. If no DTCs are output when
checking for DTCs, there may be a problem with the combina-
tion meter or the multiplex communication system.
Use the hand±held tester or SST to check and solve the prob-
lem.
SST 09843±18040
2. CHECK THE DLC3
The vehicle's ECM uses ISO 9141±2 for communication. The
terminal arrangement of the DLC3 complies with SAE J1962
and matches the ISO 9141±2 format.
Symbols (Terminals No.)Terminal DescriptionConditionSpecified Condition
SIL(7) ± SG(5)Bus º+º lineDuring transmissionPulse generation
CG(4) ± Body groundChassis groundAlwaysBelow 1 W
SG(5) ± Body groundSignal groundAlwaysBelow 1 W
BAT(16) ± Body groundBattery positiveAlways11 to 14 V
HINT:
If the display shows ºUNABLE TO CONNECT TO VEHICLEº af-
ter connecting the hand±held tester to the DLC3, turning the
ignition switch to the ON position and operating the tester, there
is a problem on either the vehicle side or the tool side.

If communication is normal when the tool is connected to
another vehicle, inspect the DLC3 on the original vehicle.

If communication is still impossible when the tool is con-
nected to another vehicle, the problem is probably in the
tool itself, so consult the Service Department listed in the
tool's instruction manual.

DIDF0±01
A04550
TC CG
1 2345678
9
10 11 12 1314 15 16
I11929
CRUISE Main
Indicator Light
I28693
Normal System Code:
ON
OFF
Code 52
Code 21 0.25 sec.
0.25 sec.
ON
OFFDiagnostic Trouble Code:
4.5 sec. 2.5 sec. 1.5 sec. 0.5 sec.
0.5 sec.
± DIAGNOSTICSCRUISE CONTROL SYSTEM
DI±1545
1739 Author: Date:
2005 SEQUOIA (RM1146U)
DTC CHECK / CLEAR
1. DTC CHECK (USING SST CHECK WIRE)
(a) Using SST check wire, connect terminals TC and CG
of
the DLC3.
SST 09843±18040
(b) Turn the ignition switch to the ON position.
(c) Read and record DTCs from the CRUISE main indicator
light on the combination meter. As examples, refer to the
chart below for the blinking patterns of the normal system
code, and diagnostic trouble codes 21 and 52.
(d) Refer to the Diagnostic Trouble Code Chart (see page
DI±1549) for DTC information.
2. DTC CLEAR (USING SST CHECK WIRE)
Remove the EFI No.1 and ETCS fuses from the engine room
J/B for more than 60 seconds, or disconnect the battery termi-
nal for more than 60 seconds.

I24840
Battery 117
1E
AM2
1 2W±RI18
Ignition SW
B±R
IG2
85E4ECM
ST1± 1
STOP16
5 S14
Stop Light SW
7G±Y
3
6E4STP
1C B±O
3
F10 FL Block
ALT IGN1
B B
W
1F 1L1
2D 2C15
W±RAM2
ST2
1C2
1J 2
4A2 B±OW4
2G±Y
Instrument Panel J/B
Sub J/B No. 4
Engine Room J/B
Instrument Panel J/B4L±B Sub J/B No. 4
4D1
1
4A4E DI±1552
± DIAGNOSTICSCRUISE CONTROL SYSTEM
1746 Author: Date:
2005 SEQUOIA (RM1146U)
DTC P0571/52 Stop light switch circuit malfunction
CIRCUIT DESCRIPTION
When the brake pedal is depressed, the stop light switch assy sends a signal to the ECM. When the ECM
receives this signal, it cancels the cruise control.
Fail±safe function operates to enable normal driving even if there is a malfunction in the stop light signal
circuit.
The cancel condition occurs when positive battery voltage is applied to terminal STP.
When the brake is applied, battery positive voltage is normally applied to terminal STP of the ECM through
the STOP fuse and the stop light switch assy, and the ECM turns the cruise control off.
DTC No.DTC Detection ConditionTrouble Area
P0571/52Stop light switch does not turn off even once the vehicle is
driven
Stop light switch assy

Stop light switch assy circuit

ECM
WIRING DIAGRAM
DIAB6±05