2001 TOYOTA SEQUOIA trouble shooting

A23661
Vehicle Speed
(64 km/h and 113 km/h)Between
40 mph and 70 mph
Idling
Ignition Switch OFF
10 minutes
Time Warm up
(Note: Even if vehicle stops during driving pattern, test can be resumed)NOTICE:
This test will not be completed
if the vehicle is driven under
absolutely constant speed
conditions such as with cruise
control activated. (h)
(g)
MISFIRE MON ..................... AVAILREADINESS TESTS
CAT EVAL ......................... INCMPL
HTD CAT EVAL ...................... N/A
EVAP EVAL ....................... INCMPL
2nd AIR EVAL .......................... N/A
A/C EVAL ................................ N/A
O2S EVAL ........................ INCMPL
O2S HTR EVAL .................. INCMPL
EGR EVAL ...............................N/A COMP MON ........................ AVAIL FUEL SYS MON ................... AVAIL
A76855
A23660
DI±154
± DIAGNOSTICSENGINE
348 Author: Date:
2005 SEQUOIA (RM1146U)
CONFIRMATION DRIVING PATTER
HINT:

This confirmation driving pattern is used in steps 5, 8 and 11 of the following diagnostic troubleshooting
procedure when using either a hand±held tester.

Performing this confirmation pattern will activate the Heated Oxygen (HO2) sensor monitor. (The cata-
lyst monitor is performed simultaneously.) This is very useful for verifying the completion of a repair.
(a) Connect a hand±held tester to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the tester or scan tool ON.
(d) Clear DTCs (where set) (see page DI±43).
(e) If using a hand±held tester, select the following menu
items: DIAGNOSIS / CARB OBD II / READINESS
TESTS.
(f) Check that O2S EVAL is INCMPL (incomplete).
(g) Start the engine and warm it up.
(h) Drive the vehicle at between 40 mph and 70 mph (64 km/h
and 113 km/h) for at least 10 minutes.
(i) Note the state of the Readiness Tests items. Those items
will change to COMPL (complete) as O2S EVAL monitor
operates.
(j) On the tester, select the following menu items: DIAGNO-
SIS / ENHANCED OBD II / DTC INFO / PENDING
CODES and check if any DTCs (any pending DTCs) are
set.
HINT:
If O2S EVAL does not change to COMPL, and any pending
DTCs fail to set, extend the driving time.

+25 %
±12.5 %
More than 0.5 V
Less than 0.4 V
Case 1
Case 2
Case 3
Case 4
Output voltage of A/F sensor
(sensor 1: front sensor)
Injection volume
Output voltage
Output voltage of heated oxygen
sensor (sensor 2: rear sensor)Mainly suspected
trouble area
OK
+25 %
±12.5 %
More than 0.5 V
Less than 0.4 V
Injection volume
Output voltage
+25 %
±12.5 %
More than 0.5 V
Less than 0.4 V
Injection volume
Output voltage
Sensor 1: front sensor
(sensor 1, heater, sensor 1
circuit)
+25 %
±12.5 %
More than 0.5 V
Less than 0.4 V
Injection volume
Output voltage
+25 %
±12.5 %
Injection volume
Output voltage
NG
+25 %
±12.5 %
Injection volume
Output voltage
NG
+25 %
±12.5 %
Injection volume
Output voltage
NG
+25 %
±12.5 %
Injection volume
Output voltage
NGExtremely rich or lean actual
air±fuel ratio
(Injector, fuel pressure, gas
leakage in exhaust system,
etc.) OK
OK
OK
Almost
no reaction
'
Sensor 2: rear sensor
(sensor 2, heater, sensor 2
circuit)
Almost
no reactionAlmost
no reactionAlmost
no reaction
DI±156
± DIAGNOSTICSENGINE
350 Author: Date:
2005 SEQUOIA (RM1146U)
The following A/F CONTROL procedure enables the technician to check and graph the voltage output of
the heated oxygen sensors.
For displaying the graph indication, first enter ºACTIVE TEST / A/F CONTROL / USER DATA,º then select
ºA/F B1,2S1and O2S B1,2S2º by pressing ºYESº button, and push ºENTERº button before pressing ºF4º
button.
HINT:

If different DTCs that are related to different system are output simultaneously while terminal E2 is used
as a ground terminal, terminal E2 may be open.

Read freeze frame data using the hand-held tester. Freeze frame data records the engine conditions
when a malfunction is detected. When troubleshooting, it is useful for determining whether the vehicle
was running or stopped, the engine was warmed up or not, the air±fuel ratio was lean or rich, etc. when
a malfunction occurred.

DI±170
± DIAGNOSTICSENGINE
364 Author: Date:
2005 SEQUOIA (RM1146U)
HINT:

Read freeze frame data using a hand±held tester. Freeze frame data record the engine condition when
malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle
was moving or stationary, if the engine was warmed up or not, if the air±fuel ratio was lean or rich, and
other data, from the time the malfunction occurred.

A low A/F sensor voltage could be caused by a rich air±fuel mixture. Check for conditions that would
cause the engine to run rich.

A high A/F sensor voltage could be caused by a lean air±fuel mixture. Check for conditions that would
cause the engine to run lean.
1 Check any other DTCs output (in addition to DTC P0171, P0172, P0174 or P0175).
PREPARATION:
(a) Connect a hand±held tester to the DLC3.
(b) Turn the ignition switch to ON and turn the tester ON.
(c) Select the following menu items: DIAGNOSIS / ENHANCED OBD II / DTC INFO / CURRENT CODES.
CHECK:
(a) Read DTCs.
Result:
Display (DTC Output)Proceed To
P0171, P0172, P0174 or P0175A
P0171, P0172, P0174 or P0175 and other DTCsB
HINT:
If any DTCs other than P0171, P0172, P0174 or P0175 are output, troubleshoot those DTCs first.
B Go to DTC chart (See page DI±58).
A
2 Check connection of PCV piping.
OK:
PCV hose is connected correctly and is not damaged.
NG Repair or replace PCV piping.
OK

B17411
E6E1
FPR
A21024
DI±182
± DIAGNOSTICSENGINE
376 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION PROCEDURE
HINT:
Read freeze frame data using the hand-held tester. Freeze frame data records the engine conditions when
a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was
running or stopped, if the engine was warmed up or not, if the air±fuel ratio was lean or rich, as well as other
data from the time when a malfunction occurred.
1 Check voltage between terminal FPR and E1 of ECM.
CHECK:
Measure the voltage between terminals of E6 and E6 ECM con-
nectors.
OK:
Tester ConnectionConditionSpecified Condition
FPR (E6±30) ± E1 (E6±1)STA signal ON9 to 14 V
FPR (E6±30) ± E1 (E6±1)STA signal OFF0 to 3 V
OK Replace ECM (See page SF±80).
NG
2 Check fuel pump relay.
PREPARATION:
Remove the fuel pump relay from the engine room R/B.
CHECK:
Inspect the fuel pump relay.
OK:
Terminal No.ConditionSpecified Condition
3 ± 4Apply B+ between
terminals 1 and 210 KW or higher
3 ± 4AlwaysBelow 1 W
3 ± 5Always10 KW or higher
3 ± 5Apply B+ between
terminals 1 and 2Below 1 W
NG Replace fuel pump relay.
OK

DI±192
± DIAGNOSTICSENGINE
386 Author: Date:
2005 SEQUOIA (RM1146U)
1 Are there any other codes (besides DTC P0300, P0301, P0302, P0303, P0304
P0305, P0306, P0307 or P0308) being output?
PREPARATION:
(a) Connect the hand±held tester to the DLC3.
(b) Turn the ignition switch ON and push the hand±held tester main switch ON.
(c) When using hand±held tester, enter the following menu: DIAGNOSIS / ENHANCED OBD II / DTC
INFO / CURRENT CODES.
CHECK:
Read the DTCs using hand±held tester.
RESULT:
Display (DTC Output)Proceed to
ºP0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307 and/or
P0308ºA
ºP0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307 or
P0308º and other DTCsB
HINT:
If any other codes besides ºP0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307 or P0308º are
output, perform the troubleshooting for those DTCs.
B Go to relevant DTC chart (See page DI±58).
A
2 Check wire harness, connector and vacuum hose in engine room.
CHECK:
(a) Check the connection conditions of the wire harness and connector.
(b) Check for the disconnection, piping and brake of the vacuum hose.
NG Repair or replace, then confirm that there is no
misfire (See confirmation driving pattern).
OK

A23549
ECU
KNK1 21
E7
B GR
4 K1
Knock Sensor 1
(Bank 1)B 8
1 K2
Knock Sensor 2
(Bank 2)
1
20KNK2
E7
BR7
2
EB4 EB4
23
EB
EC 1
BR BR
BR
E (Shielded)
BR (Shielded)
EB4 EB4
EB4(Shielded)
(Shielded)
2G
RWW
G
REKN2
EKNK
E1 E6 E7
E7 29
28
BRE D
DJ42
J/C J42
J/C DI±206
± DIAGNOSTICSENGINE
400 Author: Date:
2005 SEQUOIA (RM1146U)
TYPICAL MALFUNCTION THRESHOLDS
Detection CriteriaThreshold
Knock sensor range check (Chattering) P0325, P0330:
Knock sensor voltageLess than 0.5 V, or more than 4.5 V
Knock sensor range check (Low voltage) P0327, P0332:
Knock sensor voltageLess than 0.5 V
Knock sensor range check (High voltage) P0328, P0333:
Knock sensor voltageMore than 4.5 V
WIRING DIAGRAM
INSPECTION PROCEDURE
HINT:

DTC P0325, P0327 and P0328 are for the bank 1 knock sensor circuit.

DTC P0330, P0332 and P0333 are for the bank 2 knock sensor circuit.

Read freeze frame data using the hand±held tester. Freeze frame data records the engine conditions
when a malfunction is detected. When troubleshooting, freeze frame data can help determine if the
vehicle was running or stopped, if the engine was warmed up or not, if the air±fuel ratio was lean or
rich, and other data from the time the malfunction occurred.

A21026
Component Side
C2
Crankshaft Position Sensor
± DIAGNOSTICSENGINE
DI±213
407 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION PROCEDURE
HINT:

Read freeze frame data using the hand±held tester. Freeze frame records the engine conditions when
a malfunction is detected. When troubleshooting it is useful for determining whether the vehicle was
running or stopped. the engine was warmed up or not, the air±fuel ratio lean or rich, etc. at the time
of the malfunction.

READ VALUE ON HAND±HELD TESTER
(a) Connect the hand±held tester to the DLC3.
(b) Start the engine and push the hand±held tester tool main switch ON.
(c) When using hand±held tester, enter the following menu: ºDIAGNOSIS / ENHANCED OBD II / DATA
LIST / ALL / ENGINE SPDº.

The engine speed can be confirmed in DATA LIST using the hand±held tester. If there are no NE sig-
nals from the crankshaft position sensor despite the engine revolving, the engine speed will be indi-
cated as zero. If voltage output of the crankshaft position sensor is insufficient, the engine speed will
be indicated as lower RPM (than the actual RPM).
1 Check resistance of crankshaft position sensor.
PREPARATION:
Disconnect the C2 crankshaft position sensor connector.
CHECK:
Measure the resistance between terminals 1 and 2.
OK:
Standard:
Tester ConnectionSpecified Condition
1 ± 2985 to 1,600 W at cold
1 ± 21,265 to 1,890 W at hot
NOTICE:
º Coldº and ºHotº shown above mean the temperature of
the coils themselves. ºColdº is form ±10°C (14°F) to 50°C
(122°F) and ºHotº is from 50°C (122°F) to 100°C (212°F).
NG Replace crankshaft position sensor.
OK

DI±218
± DIAGNOSTICSENGINE
412 Author: Date:
2005 SEQUOIA (RM1146U)
TYPICAL MALFUNCTION THRESHOLDS
Detection CriteriaThreshold
P0340, P0345 Case 1:
VVT sensor signalNo signal
P0340, P0345 Case 2:
VVT sensor signalNo signal
P0341, P0346:
VVT sensor count12 or more / 720CA (= Engine 2 revolutions)
COMPONENT OPERATING RANGE
ParameterStandard Value
VVT sensor signal input during every 720CA3
WIRING DIAGRAM
Refer to DTC P0335 on page DI±210.
INSPECTION PROCEDURE
HINT:
Read freeze frame data using the hand-held tester. Freeze frame data records the engine conditions when
a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was
running or stopped, if the engine was warmed up or not, if the air±fuel ratio was lean or rich, as well as other
data from the time when a malfunction occurred.
1 Check resistance of camshaft position sensor (See page SF±76).
NG Repair or replace harness or connector.
OK