2001 TOYOTA SEQUOIA battery

± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
DI±1349
1543 Author: Date:
2005 SEQUOIA (RM1146U)
2 Replace occupant classification ECU.
(a) Turn the ignition switch to the LOCK position.
(b) Disconnect the negative (±) terminal cable from the battery, and wait for at least 90 seconds.
(c) Replace the occupant classification ECU (see page RS±111).
HINT:
Perform the inspection using parts from a normal vehicle if possible.
NEXT
3 Perform zero point calibration.
(a) Connect the negative (±) terminal cable to the battery.
(b) Connect the hand±held tester to the DLC3.
(c) Turn the ignition switch to the ON position.
(d) Using the hand±held tester, perform ºZero point calibrationº (see page DI±1128).
OK:
The ºCOMPLETEDº is displayed.
NEXT
4 Perform sensitivity check.
Using the hand±held tester, perform ºSensitivity checkº (see page DI±1128).
OK:
Standard value: 27 to 33 kg (59.52 to 72.75 lb)
NEXT
END

± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
DI±1351
1545 Author: Date:
2005 SEQUOIA (RM1146U)
2 Replace occupant classification ECU.
(a) Turn the ignition switch to the LOCK position.
(b) Disconnect the negative (±) terminal cable from the battery, and wait for at least 90 seconds.
(c) Replace the occupant classification ECU (see page RS±111).
HINT:
Perform the inspection using parts from a normal vehicle if possible.
NEXT
3 Perform zero point calibration.
(a) Connect the negative (±) terminal cable to the battery.
(b) Connect the hand±held tester to the DLC3.
(c) Turn the ignition switch to the ON position.
(d) Using the hand±held tester, perform ºZero point calibrationº (see page DI±1128).
OK:
The ºCOMPLETEDº is displayed.
NEXT
4 Perform sensitivity check.
Using the hand±held tester, perform ºSensitivity checkº (see page DI±1128).
OK:
Standard value: 27 to 33 kg (59.52 to 72.75 lb)
NEXT
END

DI±1354
± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
1548 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION PROCEDURE
CAUTION:
Be sure to perform the following procedures before troubleshooting to avoid unexpected airbag de-
ployment.
(a) Turn the ignition switch to the LOCK position.
(b) Disconnect the negative (±) terminal cable from the battery, and wait for at least 90 seconds.
(c) Disconnect the connectors from the airbag sensor assembly.
(d) Disconnect the connectors from the steering wheel pad.
(e) Disconnect the connectors from the front passenger airbag assembly.
(f) w/ Side and curtain shield airbag:
Disconnect the connectors from the side airbag assembly LH and RH.
(g) w/ Side and curtain shield airbag:
Disconnect the connectors from the curtain shield airbag assembly LH and RH.
(h) Disconnect the connectors from the front seat outer belt LH and RH.
1 Check DTC.
CHECK:
Proceed to each step according to how to read DTC.
(1) If using the hand±held tester (read the 5±digit of DTC):
Using the hand±held tester, check the DTCs (see page DI±1147).
RESULT:
DTC B1800 is output.A
DTC B1801 is output.B
DTC B1802 is output.C
DTC B1803 is output.D
(2) If not using the hand±held tester (read the 2±digit of DTC):
Check the DTCs (see page DI±1147).
RESULT:
DTC 51 is output.E
HINT:
Codes other than DTC B1800, B1801, B1802, B1803 and DTC 51 may be output at this time, but they are
not related to this check.
B Go to step 4.
C Go to step 5.
D Go to step 6.
E Go to step 7.
A

H23795H23974
H01001H23987
D+
D±
Color: Orange
D Squib
Spiral
CableA
B C D E FAirbag
Sensor
Assembly
± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
DI±1357
1551 Author: Date:
2005 SEQUOIA (RM1146U)
6 Check D squib (short to B+).
PREPARATION:
Connect the negative (±) terminal cable to the battery, and wait
for at least 2 seconds.
CHECK:
(a) Turn the ignition switch to the ON position.
(b) Measure the voltage according to the value(s) in the table
below.
OK:
Tester ConnectionConditionSpecified Condition
D+ ± Body groundIgnition switch ONBelow 1 V
D± ± Body groundIgnition switch ONBelow 1 V
NG Go to step 19.
OK
Go to step 11.
7 Check connector.
CHECK:
Check that the spiral cable connectors (on the steering wheel pad side) are not damaged.
OK:
The lock button is not disengaged, or the claw of the lock is not deformed or damaged.
NG Replace spiral cable (see page RS±21).
OK

H23795H23974
H01001H23987
D+
D±
Color: Orange
D Squib
Spiral
CableA
B C D E FAirbag
Sensor
Assembly
DI±1358
± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
1552 Author: Date:
2005 SEQUOIA (RM1146U)
8 Check D squib circuit.
PREPARATION:
Connect the negative (±) terminal cable to the battery, and wait
for at least 2 seconds.
CHECK:
(a) Turn the ignition switch to the ON position.
(b) Measure the voltage according to the value(s) in the table
below.
OK:
Tester ConnectionConditionSpecified Condition
D+ ± Body groundIgnition switch ONBelow 1 V
D± ± Body groundIgnition switch ONBelow 1 V
PREPARATION:
(a) Turn the ignition switch to the LOCK position.
(b) Disconnect the negative (±) terminal cable from the bat-
tery, and wait for at least 90 seconds.
CHECK:
Measure the resistance according to the value(s) in the table
below.
OK:
Tester ConnectionConditionSpecified Condition
D+ ± D±AlwaysBelow 1 W
D+ ± Body groundAlways1 MW or higher
D± ± Body groundAlways1 MW or higher
PREPARATION:
Release the activation prevention mechanism built into the con-
nector ºBº (see page DI±1137).
CHECK:
Measure the resistance according to the value(s) in the table
below.
OK:
Tester ConnectionConditionSpecified Condition
D+ ± D±Always1 MW or higher
NG Go to step 21.
OK

H01003H10600H01075H23352
D Squib
Spiral
CableAirbag
Sensor
Assembly
DTC 51
DLC3
TC CG
FEDC
± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
DI±1359
1553 Author: Date:
2005 SEQUOIA (RM1146U)
9 Replace steering wheel pad (D squib).
PREPARATION:
(a) Replace the steering wheel pad (see page RS±21).
HINT:
Perform the inspection using parts from a normal vehicle if pos-
sible.
(b) Connect the connectors to the airbag sensor assembly.
(c) Connect the negative (±) terminal cable to the battery,
and wait for at least 2 seconds.
CHECK:
(a) Turn the ignition switch to the ON position, and wait for at
least 60 seconds.
(b) Clear the DTCs stored in memory (see page DI±1147).
(c) Turn the ignition switch to the LOCK position.
(d) Turn the ignition switch to the ON position, and wait for at
least 60 seconds.
(e) Check the DTCs (see page DI±1147).
OK:
DTC 51 is not output.
HINT:
Codes other than DTC 51 may be output at this time, but they
are not related to this check.
NG Replace airbag sensor assembly
(see page RS±82).
OK
END

H01002H23349
D Squib
Spiral
CableAirbag
Sensor
Assembly
C D
E F
DI±1360
± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
1554 Author: Date:
2005 SEQUOIA (RM1146U)
10 Check airbag sensor assembly.
PREPARATION:
(a) Connect the connectors to the airbag sensor assembly.
(b) Connect the negative (±) terminal cable to the battery,
and wait for at least 2 seconds.
CHECK:
(a) Turn the ignition switch to the ON position, and wait for at
least 60 seconds.
(b) Clear the DTCs stored in memory (see page DI±1147).
(c) Turn the ignition switch to the LOCK position.
(d) Turn the ignition switch to the ON position, and wait for at
least 60 seconds.
(e) Check the DTCs (see page DI±1147).
OK:
DTC B1800 is not output.
HINT:
Codes other than DTC B1800 may be output at this time, but
they are not related to this check.
NG Replace airbag sensor assembly
(see page DI±1137).
OK
Go to step 12.

H23975H01002H23988
D Squib
D+ D±
Spiral
Cable
Color: Orange Service Wire
C D
E F
Airbag
Sensor
Assembly
± DIAGNOSTICSSUPPLEMENTAL RESTRAINT SYSTEM
DI±1361
1555 Author: Date:
2005 SEQUOIA (RM1146U)
11 Check airbag sensor assembly.
PREPARATION:
(a) From the step 6:
Turn the ignition switch to the LOCK position.
(b) From the step 6:
Disconnect the negative (±) terminal cable from the bat-
tery, and wait for at least 90 seconds.
(c) Connect the connectors to the airbag sensor assembly.
(d) Using a service wire, connect D+ and D± of the connector
ºEº.
NOTICE:

Twist the end of the service wire in order to insert it
into the connector.

Do not forcibly insert the twisted service wire into the
terminals of the connector when connecting.
(e) Connect the negative (±) terminal cable to the battery,
and wait for at least 2 seconds.
CHECK:
(a) Turn the ignition switch to the ON position, and wait for at
least 60 seconds.
(b) Clear the DTCs stored in memory (see page DI±1147).
(c) Turn the ignition switch to the LOCK position.
(d) Turn the ignition switch to the ON position, and wait for at
least 60 seconds.
(e) Check the DTCs (see page DI±1147).
OK:
DTC B1801, B1802 or B1803 is not output.
HINT:
Codes other than DTC B1801, B1802 and B1803 may be out-
put at this time, but they are not related to this check.
NG Replace airbag sensor assembly
(see page RS±82).
OK